Community : Document List - Relay Digital Wireless

Switching between RF1 and RF2 modes

support@line6.com — Mon, 26 Nov 2012 22:10:50 GMT

Klicken Sie bitte den folgenden Link um dieses Document in Deutsch zu öffnen. ( Frequenzmodus wechseln)

Pour consulter ce document en français s'il vous plaît cliquer sur le lien ci-dessous. ( Changement mode)

Line 6 Wireless Modes RF2 & RF1

The new V75, 55 and 35 default to RF2 mode, but include the ability to be switched into RF1 mode. You cannot use RF2 mode in the presence of any older Line 6 2.4G wireless (including Relay) in the same venue. If you try you will likely get failures in both the old and new units. Just say no! You can check using the RF scan feature included in XD-V75 receivers.

You must either flash older models to the newer V2.0 firmware (and you must have access to a V75 receiver and do this via Monkey) or you can shift the newer models (or any that have been flashed with V2.0) into RF1 mode.

If an XD-V75 unit is being added to a setup that already includes any devices running in RF1 mode, the XD-V75 can be used to update the older devices to run RF2 mode by using an internet-connected computer attached to the XD-V75’s USB port. See the Firmware Updating Procedure section for more information. Alternatively, the XD-V75 transmitters can be set up to operate in RF1 mode if it is necessary to use the transmitters with older Line 6 receivers.

Note: Relay G30 and G50 Receivers that have been updated to V2.0 firmware will *follow* the RF Mode that the corresponding G30 or G50 Transmitter is set to.

To Set The THH12 Or TBP12 Transmitters (Including Relay G50/90):

Enter Setup mode to display the current channel
While holding down the SELECT button, press and release the ON/MUTE button on the THH12 or VALUE button on the TBP12, then release the SELECT button. The display will briefly show [XD-V75 RF1] or [XD-V75 RF2] to indicate whether it is operating in the old or new mode, respectively. This setting is retained when powering off, so as a reminder the display will also show this indication [RF1 or RF2] each time power is turned on. The XD-V75 receiver will display a [To] on the far right of the display to indicate while communicating with a RF1 software transmitter. [Tx] indicates units operating in RF2 mode. They must ALL be the same.

The XD-V35 system ships set to the new dual frequency RF2 mode. To use an XD-V35 version transmitter with an earlier generation XD-V30 receiver (RF1 mode), you must change the transmitter from RF2 mode to RF1 mode. The method differs slightly between the handheld and beltpack.

Setting THH06 And TBP06 Transmitters (Including G30): THH06 HandheldTransmitter

Turn the transmitter off.
Press and hold the channel SELECT button.
While holding the SELECT button, press and hold the power ON button.
The blue LED over channel 1 will flash three times to indicate that the transmitter is in the RF1 mode.
To revert to the RF2 mode, repeat the above steps; the blue LED over channel 2 will flash three times when the transmitter is in this mode.

TBP06 BeltpackTransmitter

With transmitter off, set the Channel Select slide switch to channel 6.
Turn on the transmitter.
Immediately slide the Channel Select switch completely left to channel 1.
Quickly slide the Channel Select switch completely right to channel 6.
Quickly slide the Channel Select switch completely left to channel 1.
This process must be completed within three seconds of turning on the transmitter.
The blue LED will flash once to indicate that the transmitter is now in the 4-frequency transmission mode. To revert to RF2 transmission mode, repeat the above steps; the blue LED will flash twice when the transmitter is in this mode.

Note: It is IMPORTANT to note that once you shift (in either direction) the transmitters will only remember the change if you power cycle the transmitter. Just turn it off with the power switch and then back on. If you were to pop a battery before doing this then it will revert back to the last "saved" mode. ----------------------------------------------------------------------------------------------------------------------------------------------

Line 6 Wireless RF1 und RF2: Frequenzmodus wechseln Line 6 Wireless Modus RF2 & RF1 Die neuen Line 6 Wireless Sender V75, 55 und 35 werden im RF2-Modus ausgeliefert, sie können aber auch in den RF1-Modus umgeschaltet werden. Der RF2-Modus kann nicht benutzt werden, wenn ältere Line 6 2.4G Wireless-Geräte (inklusive Relay) am gleichen Ort verwendet werden, weil das zu Störungen bei beiden Gerätetypen führen kann. Welcher Modus gerade eingeschaltet ist, können Sie herausfinden, indem Sie die eingebaute Frequenzen-Scan-Funktion Ihres XD-V75-Empfängers benutzen.Um das Problem zu beheben, müssen sie entweder die neuere V2.0-Firmware auf ihre älteren Geräte aufspielen (dazu brauchen Sie Zugang zu einem V75-Empfänger und Monkey), oder sie schalten die neueren Modelle (beziehungsweise jedes Modell, auf dem die V2.0-Firmware läuft) in den RF1-Modus um.Wenn ein XD-V75-Gerät zu einem Setup hinzugefügt wird, das schon Geräte enthält, die im RF1-Modus laufen, kann das XD-V75 benutzt werden, um die älteren Geräte zu aktualisieren. Dazu brauchen Sie einen Computer mit Internetverbindung, der an den USB-Port des XD-V75 angeschlossen wird. Weitere Informationen dazu finden Sie in der Sektion über Firmware-Aktualisierung. Alternativ können Sie das Setup in den RF-1-Modus umschalten, um die Sender mit älteren Line-6-Empfängern zu verwenden.

Bitte beachten Sie: Relay G30- und G50-Empfänger, die auf die V2.0-Firmware aktualisiert wurden, „folgen“ automatisch derjenigen Frequenz, auf die der dazugehörige G30- oder G50-Empfänger eingestellt wurde.

Einstellen des THH12 oder TBP12 Senders (Inklusive Relay G50/90):

1. Gehen Sie in den Setup-Modus, um den aktuellen Kanal anzuzeigen
2. Halten Sie den SELECT-Knopf gedrückt, drücken Sie dann den ON/MUTE-Knopf (beim THH12) beziehungsweise den VALUE-Knopf (beim TBP12) und lassen Sie ihn wieder los. Das Display wird kurz [XD-V75 RF1] oder [XD-V75 RF2] anzeigen, so können Sie sehen, ob der Transmitter im alten oder neuen Modus läuft. Die Einstellung wird beibehalten, wenn Sie das Gerät ausschalten. Zur Erinnerung zeigt das Display den jeweiligen Modus [RF1 oder RF2] beim Einschalten des Geräts kurz an. Der XD-V75-Receiver zeigt an der äußersten rechten Seite [To] an, wenn das Gerät mit einem RF1-Transmitter kommuniziert. [Tx] bedeutet, dass die Geräte im RF2-Modus arbeiten. Damit die verschiedenen Sender- Empfänger Generationen zusammen störungsfrei arbeiten müssen ALLE Geräte im gleichen Modus arbeiten.

Bedeutet das Vorhandensein eines Senders im RF1 modus.Bedeutet das Vorhandensein eines Senders im RF2 modus. Das XD-V35-System ist bei der Auslieferung auf den neuen Dual-Frequenz-Modus RF2 eingestellt. Um einen XD-V35-Sender mit einem XD-V30-Empfänger der früheren Generation (RF1-Modus) zu verwenden, müssen Sie den Sender von RF2 auf RF1 umschalten. Die Vorgehensweise ist etwas unterschiedlich, je nachdem, ob Sie das Mikrofon- oder das Beltpack-Gerät verwenden.

Einstellen des THH06 und TBP06 Transmitters (Inklusive G30): THH06 Handheld-Transmitter

1. Schalten Sie den Transmitter aus.

2. Halten Sie den Kanal-Select-Knopf gedrückt.

3. Während Sie den Select-Knopf gedrückt halten, drücken Sie den Power/Ein-Knopf und halten Sie diesen ebenfalls gedrückt.

4. Die blaue LED über Kanal 1 leuchtet dreimal kurz auf, um anzuzeigen, dass der Transmitter jetzt im RF1-Modus ist.

5. Um in den RF2-Modus zurückzukehren, wiederholen Sie die oben genannten Schritte; die blaue LED über Kanal 2 leuchtet dreimal kurz auf, um anzuzeigen, dass der Transmitter im RF2-Modus ist.

TBP06 Beltpack-Transmitter

1. Bei ausgeschaltetem Transmitter den Schieberegler zur Kanalauswahl auf Kanal 6 stellen.

2. Transmitter einschalten.

3. Den Schieberegler sofort nach dem Einschalten auf Kanal 1 stellen, zurück auf 6 und wieder auf Kanal 1 schieben.

4. Dieser Prozess muss nach Anschalten des Senders innerhalb von drei Sekunden geschehen.

5. Die blaue LED blinkt einmal, um anzuzeigen, dass der Sender jetzt im 4-Frequenzen-Übertragungsmodus ist. Um in den RF2-Übertragungsmodus zurückzukehren, wiederholen Sie die oben genannten Schritte. Die blaue LED blinkt dann zweimal auf, wenn der Sender im RF2-Modus ist.

Wichtig: Bitte beachten Sie, dass das Gerät den soeben eingestellten Modus (egal in welche Richtung) nur beibehält, wenn Sie das Gerät nach dem Wechsel kurz aus- und wieder einschalten. Dadurch wird der aktuell eingestellte Modus gespeichert. Wenn sie vorher eine Batterie eingelegt haben, springt das Gerät zurück zum zuletzt gespeicherten Modus.-------------------------------------------------------------------------------------------------------------------------------

Line 6 sans fil RF1 et RF2: Changement de modes Les modes de transmission RF2&RF1 Line6
Les nouveaux systèmes sans fil V75, 55 et 35 utilisent le nouveau mode de transmission RF2 par défaut, mais possèdent la possibilité de changer en mode RF1.Il n’est pas possible d’utiliser des appareils qui utilisent le mode RF2 s’il y a des anciens appareils RF1(V70 our Relay) sur la même scène ou dans le même bâtimentSi vous l’essayez, vous allez très probablement voir des erreurs de communication sur les anciens et nouveaux systèmes. Il suffit de ne pas les combiner ! Vous pouvez vérifier la présence d’émetteurs RF1 /FR2 en utilisant la fonction « CHANNEL SCAN » RF dans les récepteurs XD-V75. Vous devez soit mettre a jour les anciens modèles vers la version 2.0 ou vous pouvez changer les modèles déjà équipés de la version 2.0 en RF mode 1.
Pour mettre à jour un ancien modèle, vous avez besoin d’un récepteur XDV75, un ordinateur et le logiciel Monkey. Si une XD-V75 est ajouté à une installation qui comprend déjà des appareils fonctionnant en mode RF1, le XD-V75 peut être utilisé pour mettre à jour les appareils plus anciens vers RF2 mode.Pour mettre à jour les modèles précédents, vous devrez avoir accès à l'Internet et une connexion USB entre le XD-V75 à l'ordinateur Voir la section Mise à jour ‘’Firmware Procedure’’ pour de plus amples renseignements. Alternativement, les émetteurs XD-V75 peut être configuré en mode de RF1 s'il est nécessaire d'utiliser des émetteurs avec les anciens Line 6 récepteurs.

Remarque : Les récepteurs Relay G30 et G50 qui ont été mis à jour avec le firmware V2.0 suivent automatiquement le mode RF de l’émetteur correspondant.

Pour changer le mode RF des émetteurs THH12TBP12et G50/90:
1. Entrez en mode de configuration pour afficher le canal actuel
2. Maintenez le bouton SELECT et pressez et relâchez le bouton ON / MUTE ou la touche VALUE sur le TBP12. L'écran indiqué brièvement [XD-V75 RF1] ou [XD-V75 RF2] pour vous indiquer le mode actif. Également quand vous mettez l’émetteur en marche.Ce réglage est conservé lorsque vous éteignez l’émetteur. Le mode actif [RF1 ou RF2] s’indique chaque fois que l'appareil est allumé. Le récepteur XD-V75 affichera une Icône ( To) à la droite de l'écran pour indiquer le mode RF2, ( Tx)s’indique que l récepteur est en communication avec un émetteur dans mode RF1. Ils doivent tous être les mêmes.montre la présence d’un émetteur RF1montre la présence d’un émetteur RF2

Le système XD-V35 est déjà réglé à la nouvelle fréquence RF2.Pour utiliser un émetteur XD-V35 avec un récepteurXD-V30 d’ancienne génération RF1 vous devez changer l'émetteur de RF2 mode RF1. La méthode diffère légèrement entre le modèle micro THH06 et le modèle ceinture TBP06 (et G30).

Pour changer le mode RF des émetteurs THH06TBP06et G30: THH06 émetteur micro :

1/ éteignez l'émetteur.
2/ appuyez et maintenez enfoncé le bouton SELECT canal.
3/ tout en maintenant la touche SELECT, appuyez et maintenez le bouton d'alimentation.
4/ Le LED bleu sur le canal 1 clignote trois fois pour indiquer que l'émetteur est en mode RF1.
5/ pour revenir en mode RF2, répétez les étapes ci-dessus, le LED bleu sur le canal 2 clignote trois fois lorsque l'émetteur est dans ce mode.

TBP06 émetteur ceinture :

1/ éteignez l'émetteur.

2/ mettez le sélecteur de canal sur 6.
3/ allumez l'émetteur et changez immédiatement le canal vers 1, vers 6 et vers 1.

4/ ce processus doit être achevé dans les trois secondes après la mise sous tension de l'émetteur.
5/ le LED bleu clignote une fois pour indiquer que l'émetteur est maintenant dans le mode de transmission RF1. Pour revenir en mode RF2, répétez les étapes ci-dessus le LED bleu clignote deux fois lorsque l'émetteur est dans ce mode.

Remarque: Pour sauvegarder le changement de mode RF dans l’émetteur, il vous suffit de l’éteindre et de le rallumer avec avec le commutateur ON/OFF.Si vous enlevez les piles, l’émetteur se met dans le dernier mode RF saufgardé.

Line 6 ワイヤレス・モードRF2とRF1について
新しいXD-V75、V55、V35の初期設定はRF2モードですが、RF1モードへ切り替えることも可能になっています。従来のLine 6 2.4 GHzワイヤレス (Relayを含む) と同じ会場内で、同時にRF2モードを使うことはできません。もし行なった場合は両方のユニットで問題が起こる可能性がありますので、絶対に行わないようにしてください。どのモードが使われているかは、XD-V75のレシーバーに搭載されたRFスキャン機能を使ってチェックすることが可能です。
問題を解決するには、従来のモデルを新しいV2.0ファームウェアに書き換えるか (Monkeyを使って書き換えを行うにはXD-V75レシーバーを使う必要があります)、新しいモデル (あるいはV2.0へアップデートされたモデル) をRF1モードにシフトします。
RF1モードのディバイスを含むセットアップへXD-V75ユニットを追加した場合、そのXD-V75を使って以前のディバイスをアップデートできます。その際はXD-V75のUSBポートへ、インターネット接続したコンピューターを接続して行います。ファームウェア・アップデートの方法は、XD-V75の製品ページのリソースタブに用意されているPDFファイルをご覧ください。なお、XD-V75のトランスミッターを以前のLine 6レシーバーで使用する必要がある場合は、そのトランスミッターをRF1に設定することもできます。
注意: V2.0ファームウェアにアップデートされたRelay G30やG50のレシーバーは、対応するG30やG50のトランスミッターで設定されたRFモードに従います。
THH12、TBP12トランスミッターの設定方法 (Relay G50/90を含む):

Setupモードに入って現在のチャンネルを表示します。

SELECTボタンを押しながら、THH12のON/MUTEボタン、もしくはTBP12のVALUEボタンを一度押して、離します。新旧どちらのモードで動作しているかがディスプレイ上に [XD-V75 RF1] または [XD-V75 RF2] の形で表示されます。同じことを繰り返すと別のモードに切り替わります。この設定は電源オフ時にも維持され、電源投入時に [RF1] または [RF2] と表示されます。XD-V75レシーバーでチャンネル・スキャンを行うと、RF1ソフトウェアのトランスミッターとコミュニケーションしている際にはディスプレイ内のチャンネル番号の上に [To] が表示されます。RF2モードで動作しているユニットの場合は [Tx] が表示されます。複数のユニットを使用している場合は、どちらか一方に全ユニットを統一する必要があります。

XD-V35システムは新しい2周波数 (デュアルフリケンシー) 方式のRF2モードに設定された状態で出荷されています。XD-V35のトランスミッターを前世代のXD-V30レシーバー (RF1モード) で使用する場合には、トランスミッターをRF2モードからRF1モードへ切り替える必要があります。その方法はハンドヘルドとベルトパックで少し異なっています。THH06、TBP06トランスミッターの設定方法 (G30を含む):
THH06ハンドヘルド・トランスミッター

トランスミッターの電源を切ります。
チャンネルのSELECTボタンを押したままにします。
そのままの状態で、電源のONボタンを押し続けます。
チャンネル1の上にある青いLEDが3回点滅して、トランスミッターがRF1モードになったことを示します。
RF2モードに戻すには、同じプロセスを繰り返します。モードが変わると、チャンネル2の上にある青いLEDが3回点滅します。

TBP06ベルトパック・トランスミッター

トランスミッターがオフの状態で、Channel Selectスライド・スイッチをチャンネル6に設定します。
トランスミッターの電源を入れます。
Channel Selectスイッチを左端のチャンネル1まで素早くスライドします。
Channel Selectスイッチを右端のチャンネル6まで素早くスライドします。
以上のプロセスを、電源投入後3秒以内に終わらせる必要があります。
青いLEDが1回点滅して、トランスミッターがRF1 (4周波数伝送モード) であることを示します。RF2伝送モードへ戻すには、同じステップを繰り返します。青いLEDが2回点滅します。

注意: トランスミッターのモードを変更した場合、その変更は電源を入れ直すことで記憶されます。一度電源スイッチを切ってから、再度オンにしてください。この作業を行う前に電池を抜いてしまうと、以前のモードに戻ってしまいます。

Relay G55 FAQ

support@line6.com — Tue, 02 Oct 2012 23:20:03 GMT

Q: What is the cable tone on my Relay G55 and what does it do?
A: The cable tone button simulates the slight change in tone that happens when using cables of varying length. The cable tone length that the Relay 55 uses is a 25 foot length guitar cable. At shorter lengths this change in tone is hard to recognize, but as length gets up to 100 feet and beyond, the extreme high end of your tone "rolls off" and loses volume. A cable length of 25 feet will not affect your audio below aproximately 15kHz.

Q: Can I use my Relay G55 transmitter or receiver with other Line 6 wireless?
A: Yes, all Line 6 wireless devices are compatible to work with one another. So, if you have a Line 6 XDV receiver, any transmitter from a Relay system will work with it, and vice versa. However, it is important to realize that Line 6 wireless systems in RF2 mode will not work with coresponding units in RF1 mode - regardless of the system they are from. You cannot use RF2 mode in the presence of any older Line 6 2.4G wireless (including Relay) in the same venue. If you try you will likely get failures in both the old and new units. So it is important to know if you are using RF1 or RF2 mode.

If an XD-V75 unit is being added to a setup that already includes any devices running in RF1 mode, the XD-V75 can be used to update the older devices to run RF2 mode by using an internet-connected computer attached to the XD-V75’s USB port. See the Firmware Updating Procedure section for more information. Alternatively, the XD-V75 transmitters can be setup to operate in RF1 mode if it is necessary to use the transmitters with older Line 6 receivers.

Q: How do I switch between RF2 mode and RF1 mode?
A: Relay G55 systems can be used in RF1 or RF2 mode.

To Set TBP12 Transmitters (Relay G50/55/90): Enter Setup mode by holding the select button, and you will know you are in setup mode when the current channel is displayed flashing. Continue holding the select button. Then press the value button. RF2 will display showing that you are now in RF2 mode. Press and hold select to exit setup mode. Repeat this process to switch between RF1 and RF2 mode.

Q: How can I avoid wi-fi interference?

A: Below are suggested channels settings to avoid interfering with wi-fi

Wi-FI Channel Number	Line 6 Channel Number
1	1, 12
6	2,6
11	5,8,9

Relay G30/G50/G90 Device Firmware 2.0 Update

support@line6.com — Wed, 21 Mar 2012 17:14:57 GMT

Klicken Sie bitte den folgenden Link um dieses Document in Deutsch zu öffnen. ( Firmware V2.0 aktualisierung)

Pour consulter ce document en français s'il vous plaît cliquer sur le lien ci-dessous. ( Mis à jour version 2.0)

Relay G30/G50/G90 Device Firmware 2.0 Update Release Notes

This release is recommended for all G30/G50/G90 system owners who desire compatibility with Line 6's RF2 mode products. The benefits of RF2 mode on the G30/G50/G90 are as follows:

Less impact on other devices operating in 2.4GHz space
Compatibility with other RF2 devices such as the XD-V75, XD-V55 and XD-V35

NOTE: An XD-V75 Receiver is required in order to perform this upgrade. If you cannot access an XD-V75 Receiver via a friend or retailer, please contact Line 6 Customer Service for assistance. TBP12 transmitters must currently be loaded with firmware v1.03 or greater to upgrade via Monkey. If your TBP12 has an earlier version firmware installed, it will need to be returned to Line 6 for upgrading.

How to determine the currently installed firmware version:

Relay G30 Bodypack
- Slide the Channel Switch to channel 1, then turn on the Relay G30 Bodypack.
- Wait for the LEDs to settle, then immediately switch the Channel Switch from 1 to 6, then back to 1 three times (1->6->1->6->1->6->1).
- The AUDIO LED will blink the version number - Green for the major number, and Red for the minor number, i.e. 1 green blink, 2 red blinks indicate v1.02).

Instructions for updating the Relay G30/G50/G90 Receivers:

Obtain an XD-V75 Receiver
Connect the XD-V75 Receiver to your PC or Mac using a USB cable
Disconnect, then reconnect the DC power plug for the XD-V75. "Loader Enabled" should be displayed.
Connect the XD-V75 Receiver to the G30/G50/G90 Receiver by using a cable with TRS to TRS (stereo) 1/4 inch phone plugs on either end. The cable should plug into the 1/4 inch audio output of both the XD-V75 and the G30/G50/G90 Receivers
Launch Line 6 Monkey, then Log In, then select "Relay G30/G50/G90 Receiver" as your device and follow the on screen instructions

Instructions for updating the Relay G30/G50/G90 Transmitters:

Obtain an XD-V75 Receiver
Connect the XD-V75 Receiver to your PC or Mac using a USB cable
Disconnect, then reconnect the DC power plug for the XD-V75. "Loader Enabled" should be displayed.
Launch Line 6 Monkey, then Log In, then select "Relay G30 Transmitter (1.0)" as your device and follow the on screen instructions.
If Line 6 Monkey is not able to connect to the Transmitter, select "Relay G30 (or G50/G90 depending on your system) Transmitter" as your device and follow the on screen instructions.
NOTE: G30 Transmitter owners with firmware version 1.0 should select "Relay G30 Transmitter (1.0)" in Line 6 Monkey in order to connect to the transmitter. G30 Transmitters with firmware 1.01 or later should select "Relay G30 Transmitter" in Line 6 Monkey.

***Transmitter Updaters: please use this Device Positioning document for visual reference on how to place the Transmitter to the XD-V75 Receiver for optimal data communication.

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Relay G30/G50/G90 Firmware V2.0 aktualisierung

Die neue Firmware V2.0 wird allen Nutzern empfohlen die eine Kompatibilität zwischen G30/G50/G90-Systemen und RF2-Modus-Produkten von Line 6 gewährleisten wollen. Die Vorteile des RF2-Modus sind folgende:

Weniger Einfluss auf andere Geräte, die im 2,4 GHz-Bereich arbeiten
Kompatibilität mit anderen RF2-Geräten wie XD-V75, XD-V55 und XD-V35

Bitte beachten Sie:

Für diese Aktualisierung brauchen Sie einen XD-V75 Empfänger. Wenn Sie keinen Zugriff auf einen XD-V75 Empfänger über einen Händler oder Bekannten haben dann nehmen Sie Verbindung mit dem Line6 Kundendienst auf. TBP12-Sender müssen zur Zeit mindestens die Firmware V1.03 aufgespielt haben, damit sie über Monkey aktualisiert werden können. Wenn Ihr TBP12 eine frühere Firmwareversion hat, müssen Sie es zur Aktualisierung an Line 6 schicken.

Anleitung zur Aktualisierung des Relay G30/G50/G90- Empfängers:

Besorgen Sie sich einen XD-V75- Empfänger
Verbinden Sie den XD-V75- Empfänger per USB-Kabel mit ihrem PC oder Mac
Verwenden Sie ein Kabel dass Stereo-Klinken-Stecker auf beiden Seiten des Kabels aufweist um den XD-V75- Empfänger mit dem G30/G50/G90-Empfänger zu verbinden.
Schalten Sie beide Geräte ein.
Trennen Sie den Netzstecker vom XD-V75 und verbinden Sie Ihn wieder.
Auf dem Display des XD-V75 erscheint ‚‘‘ Loader enabled‘‘.
Starten Sie Line 6 Monkey und verbinden sich mit Ihren Benutzerdaten und wählen
"Relay G30/G50/G90-Receiver" als Gerät aus.
Trennen Sie nun den Netzstecker vom G30/G50/G90 Empfänger und klicken auf ‚‘‘OK‘‘ in Monkey.
Die Nachricht ‚‘‘ Preparing Receiver erscheint auf dem Bildschirm.
Auf dem Display des XD-V75 erscheint ‚‘‘ Programming MCU‘‘
Das nächste Fenster fordert Sie auf den Netzstecker wieder mit dem G30/G50G90 zu verbinden.
Im Aktualiesierungsfenster von Monkey das nun erscheint wählen Sie ‚‘‘ FLASH MEMORY‘‘ und klicken auf ‚‘‘ UPDATE SELECTION‘‘.
Akzeptieren Sie die Lizenzbedingungen und klicken auf ‚‘‘ OK‘‘.
Das nächste Fenster weist Sie darauf hin dass die Aktualisierung vorgenommen wird, klicken Sie auf ‚‘‘ YES‘‘.
Der Fortschritt der Aktualisierung wird im Dispaly des XD-V75 angezeigt und kann einige Minuten dauern.
Wenn die Aktualisierung abgeschlossen ist bekommen Sie die Meldung von Monkey ‚‘‘Receiver update successful‘‘.
Trennen Sie nun den Netzstecker vom G30/G50G90 und verbinden Sie Ihn wieder und schalten den Empfänger ein.
Trennen Sie den Netzstecker vom XD-V75.

Anleitung zur Aktualisierung des Relay G30/G50/G90-Senders:

Besorgen Sie sich einen XD-V75-Empfänger
Verbinden Sie den XD-V75-Empfänger per USB-Kabel mit ihrem PC oder Mac
Verbinden Sie eine einzelne Antenne mit dem Antennenausgang B OUT.
Trennen Sie den Netzstecker vom XD-V75 und verbinden Sie Ihn wieder.
Auf dem Display des XD-V75 erscheint ‚‘‘ Loader enabled‘‘.
Positionieren Sie Ihren eingeschalteten Sender ( RELAY) wie unter folgendem link ( *** ) aufgezeigt über der Antenne.
Starten Sie Line 6 Monkey und verbinden sich mit Ihren Benutzerdaten.
Wählen Sie Ihr Bodypack "Relay G30/G50/G90 Bodypack" als Gerät aus.
Drücken und halten Sie den ‚‘‘ VALUE ‚‘‘ Schalter und schieben den ‚‘‘ON/OFF‘‘ Schalter in die OFF Position.
Während Sie den ‚‘VALUE‘‘ Schalter gedrückt halten drücken Sie die ‚‘‘ SELECT‘‘ Taste 8 mal bis das Zeichen ‚‘‘ LOADER‘‘ auf dem Display erscheint.
Klicken Sie auf ‚‘‘OK‘‘ in Monkey.
Eine Verbindung zum Bodypack wird aufgebaut, sollte die Verbindung nicht zustandekommen wird ein Fenster geöffnet dass Sie darauf hinweist.

( In diesem Fall einfach das Bodypack repositionieren bis sich die Nachricht von alleine schliesst)

Wählen Sie ‚‘‘ FLASH MEMORY‘‘ und klicken auf ‚‘‘ INSTALL UPDATE‘‘.
Akzeptieren Sie die Lizenzbedingungen und klicken auf ‚‘‘ OK‘‘.
Um die Aktualiesierung zu starten klicken Sie auf ‚‘‘ YES‘‘ im folgenden Fenster.
Auf dem Display des XD-V75 erscheint ‚‘‘ Programming MCU‘‘.
Die Aktualiesierung kann einige Minuten dauern.
Nachdem die Aktualisierung abgeschlossen ist schalten Sie den Bodypack ein währen Sie die ‚‘‘SELECT‘‘ Taste gedrückt halten, das Display zeigt Ihnen nun die neue Versionsnummer an.
Trennen Sie den Netzstecker vom XD-V75.

### Wenn Line 6 Monkey sich nicht mit dem Sender verbinden kann, wählen Sie „Relay G30 Transmitter“ (oder G50/G90 je nachdem, welches System Sie benutzen) als Gerät aus.

HINWEIS: Wenn Sie einen G30-Sender mit der Firmware-Version 1.0 benutzen, wählen Sie im Line 6 Monkey „Relay G30-Transmitter (1.0)“ als Gerät aus, um Monkey mit dem Sender zu verbinden. Bei G30 Sendern mit der Firmware-Version 1.01 oder höher wählen stattdessen „Relay G30-Transmitter“.

***Wenn Sie einen Sender aktualisieren:

Bitte nutzen Sie diesen Link Visuelle Referenz ,

in dem visuell dargestellt wird, wie Sie Sender und Empfänger platzieren müssen, um eine optimale Datenübertragung zu gewährleisten.

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Relay G30/G50/G90 mis à jour version 2.0

Cette mise à jour est recommandé pour tous les propriétaires de systèmes G30/G50/G90 qui désirent la compatibilité avec les produits Line 6 qui fonctionnent en mode RF2.

Voici les avantages de RF2 mode sur le G30/G50/G90 :

- Moins d'impact sur d'autres appareils fonctionnant dans le réseau 2,4 GHz
- Compatibilité avec les autres appareils RF2 comme les XD-V75,V55 et XD-XD-35

REMARQUE: Un récepteur XD-V75 est requis pour effectuer cette mise à jour.

Si vous ne pouvez pas accéder à un récepteur XD-V75 par un ami ou revendeur, veuillez contacter le Service clientèle de Line 6 pour vous assister.

Les émetteurs TBP12 doivent avoir le firmware v1.03 ou plus pour pouvoir les mettre à jour avec le logiciel Line6 monkey.

Si votre TBP12 est muni d'une version du firmware antérieure à 1.03 , l'appareil doit être retourné chez Line 6 pour la mise à jour,

veuillez alors contacter le Service clientèle de Line 6.

Instructions pour la mise à jour des Récepteurs RELAY G30/G50/G90 :

Procurez-vous un récepteur XD-V75.
Connectez le récepteur XD-V75 à votre PC ou Mac à l'aide d'un câble USB.
Branchez le récepteur XD-V75 au récepteur G30/G50/G90 en utilisant un câble jack TRS vers TRS (stéréo).Le câble jack stéréo doit être branché entre les sorties jack audio du XD-V75 et du récepteur G30/G50/G90.
Allumez les récepteurs
Débranchez, puis rebranchez le câble d'alimentation du récepteur XD-V75.
Le message ‘’ LOADER ENABLED’’apparaît sur l'affichage du XD-V75.
Lancez Line 6 Monkey, puis connectez-vous avec votre nom d'utilisateur et mot de passe, sélectionnez votre récepteur "Relay G30/G50/G90 Receiver" comme dans l’image ci-dessous.
Déconnectez le câble d'alimentation du récepteur G30/G50/G90.
Cliquez sur OK .
Le message ‘’ Preparing Receiver’’ apparaît sur l'ecran.
Sur l'écran du XD-V75, vous verrez le message ‘’ Programming MCU’’
Le message suivant vous indique de rebranchez le câble d'alimentation du récepteur G30/G50/G90.
Accepter le contrat de licence et cliquez sur ‘’OK’’
Cliquez sur ‘’ Yes’’ dans la fenêtre suivante.
L'état d'avancement de la mise à jour peut être vu sur l'écran du XD-V75 et peut prendre quelques minutes.
Le message ‘’ Receiver update successful’’ sera affiché lorsque la mise à jour est terminée.
Débranchez, puis rebranchez le câble d'alimentation du récepteur G30/G50/G90.
Débranchez le câble d'alimentation du récepteur XD-V75.
La mise à jour et complet.

Instructions pour la mise à jour des transmetteurs RELAY G30/G50/G90 :

Procurez-vous un récepteur XD-V75.
Connectez le récepteur XD-V75 à votre PC ou Mac à l'aide d'un câble USB.
Connectez une seule antenne à la sortie B OUT
Débranchez, puis rebranchez le câble d'alimentation du récepteur XD-V75
Le message ‘’ LOADER ENABLED’’apparaît sur l'affichage du XD-V75.
Positionnez votre transmetteur RELAY comme indiqué dans le lien suivant (***).
Lancez Line 6 Monkey, puis connectez-vous avec votre nom d'utilisateur et mot de passé.
Sélectionnez votre émetteur "Relay G30/G50/G90 Bodypack ".
Tout en cliquant et en maintenant le commutateur ‘’VALUE’’ déplacer le commutateur ‘’ON/OFF’’ à la position ‘’OFF’’ et cliquer 8 fois sur le bouton ‘’ SELECT’’.
Vous devriez maintenant voir le message ‘’LOADER’’ sur l'écran du émetteur.
Cliquez sur OK dans Monkey.
Une connexion avec l'

(Si vous recevez un message sur l'écran que la connexion a échoué, il suffit de repositionner le émetteur jusqu'à ce message disparait).

Choisissez Flash memory et cliquez "Update Selection" pour démarrer la mise à jour.
Accepter le contrat de licence et cliquez sur ‘’OK’’
Cliquez sur ‘’ Yes’’ dans la fenêtre suivante.
L'état d'avancement de la mise à jour peut être vu sur l'écran du XD-V75 et peut prendre quelques minutes.
Allumez le emetteur tout en maintenant ‘’SELECT’’après la mise à jour est terminée, l'écran vous montrera le nouveau numéro de version
Déconnectez le câble d'alimentation du récepteur XD-V75.

REMARQUE: Si votre émetteur G30 n’est pas reconnu par Monkey,

essayez s.v.p. de choisir « Relay G30 Bodypack (1.0) » (firmware 1.0) dans Line 6 Monkey afin de vous connecter à l'émetteur. Pour vous connecter aux transmetteurs avec le firmware 1.01 ou ultérieurs, vous devez sélectionner « Relay G30 Bodypack » dans Line 6 Monkey.

***Si vous mettez à niveau un émetteur: S'il vous plaît utilisez le lien Référence visuelle pour une référence visuelle sur la façon de placer l'émetteur au récepteur XD-V75 pour une communication de données optimale.

Digital Wireless Audio Troubleshooting

support@line6.com — Tue, 13 Dec 2011 00:41:20 GMT

As the environment is the biggest factor in wireless audio performance, there is a chance that certain environments and circumstances will not allow for satisfactory performance. This can be verified by successful performance in a different environment.

Pre-Qualification: First Things To Rule Out

Use the factory power supply
Try fresh alkaline batteries (a couple of times if it’s a battery problem), not rechargables
Try on more than one channel
Try in more than one place/venue
Check the transmitter LEDs during drops/interference. RF dropouts result in the green LEDs going completely off. Even one green LED means the signal is present and something other than the wireless system is causing the problem. If you see full red LEDs followed by quickly shifting back to green, it means that the system has re-synced (normal if the dropout is too long). The red LEDs come on only if the intended signal from a Line 6 transmitter is not present. In this case, they are showing RF competing for the same space.

Interference

Symptoms

Reduction of RF LEDs on the front panel that indicate usable RF signal strength
Audio signal muting

Possible causes

Trying to function at too great a distance
Having unintentional transmitters, such as walkie talkies or in-ear monitors, too close to a receiver
Significant amount of close-by RF signals within the same 2.4GHz range (Wi-Fi, microwave ovens, etc.)

Suggestion

"Walk test" your system in advance of an event over the entire desired range to verify that sufficient RF signal is available to avoid mutes from occurring
With transmitter off and receiver turned on, scroll through the channels. Red LEDs indicate stray RF on that channel. Choose channels that exhibit the least red LEDs. Note: Line 6 wireless WILL still operate but at reduced range.

Decreased Range

Symptoms

Reduction in range in general
Reduced range indoors vs. outdoors

Possible causes

Blocked "Line of Sight" between the receiver’s antennas and the transmitter’s antennas
Barriers such as walls or air-curtains can impede the path of radio waves
Transmitter strength reduced if it must pass through walls
Transmitting through earth (receiver in basement)
Human bodies absorbing RF energy
Cupping the bottom of the handheld mic (covering the antenna)
Beltpack transmitter is used in pocket or next to skin
Receiver antennas for the XD-V systems are very close to other intentional radiators in the same frequency band such as Wi-Fi wireless access points
Incorrect cables on paddle antennas (requires low-loss 50-ohm cables; e.g. LMR-195)

Suggestions

Improve “Line of Sight”
Use the XD-V70/G90 with remote paddle antennas and separate the antennas by several feet.
G90 Users: Make certain that you have the proper antenna jacks selected in the setup window. C&D are the front antennas and A&B are the rear. The units may work even if you have it set incorrectly, but the range may be only 10-20 feet. There is also a position for "both" as the G90 can be used with 4 antennas for increased reliability.

Weak Audio (thin audio output compared to other wireless systems)

Symptom

Weak and/or noisy audio output

Possible causes

Gain/trim settings on mixer need adjustment
Plugging into a "line level" input
Plugging into a channel with pads engaged
Using a TRS plug in the ¼” unbalanced output
The "Environment Filter" may not operate correctly if signal is too weak, especially when using lav mics

Suggestions

Adjust gain/trim as if using a wired microphone
Connect the XLR output (G90 only) on the receiver to an XLR input on the mixer
Use a mono plug in the ¼” unbalanced output, never a TRS plug
Turn “Environment Filter” off

Dropouts (“Audio” vs “RF” dropout: different paths to correct)

Symptoms

Audio signal interrupted

Possible causes

Transmitter on “low” power to save battery life and reduce RF interference to other devices
Local conditions in one or more venues, e.g. a large Wi-Fi installation in close proximity, metal walls/roof
Instruments or amps being used are faulty
Signal chain issue
Blocked “Line of Sight” between the receiver’s antennas and the transmitter’s antennas
Transmitter is muted
Loose antennas
Antennas straight up and down or too close to walls
Other XD-Vs/Relays operating on the same channel
Unused transmitter too close to receiver
Receiver’s antennas near any transmitters such as walkie-talkies, In-Ear Monitors, etc
Using a substitute power supply
Batteries dying or unseated

Suggestions

Switch transmitter to “high” power
Try a different venue to reproduce problem
Try multiple instruments/amps to reproduce problem
Trace signal through chain one component at a time. “Audio” LED lights when signal is received.
Improve “Line of Sight” by moving receiver or taking transmitter out of pocket
Unmute transmitter. On the G50/G90/V70 transmitter, the LCD screen remains lit when in mute mode.
Raise antennas to 6-8 feet high while avoiding obstacles such as metal posts, walls, etc.
Ensure antennas are connected firmly and splayed at 90 degrees with nothing touching them
Ensure each system has its own unique channel to operate on
Move intended transmitter closer to receiver than unintended transmitter to eliminate “near/far” issue. Switch closer transmitter to “low” power when possible.
Provide ample distance between the XD-V receiver and other transmitters. The distance will depend on the strength of the transmitter and the gain of the transmitting antenna.
Use the factory power supply or one that can supply the required 9v DC current: XD-V - 350 ma, G30 – 200mA, G50 – 300 mA. If you are using a pedalboard supply, it must be able to supply this amount of power to the receiver in addition to whatever else you have plugged into it.
Reinstall batteries or replace them. If using rechargables, try with standard alkaline to test.

References for working with wireless systems

http://en.wikipedia.org/wiki/Non-line-of-sight_propagation

http://www.bartlettmics.com/newsletter/newsletter%2012-10.pdf

http://www.djsociety.org/Wireless.htm

Relay Digital Wireless: What/How do I plug in?

support@line6.com — Thu, 14 Jul 2011 23:30:35 GMT

What instruments and pickups can I plug into my Relay transmitter?

Relay digital wireless systems basically just replace your instrument cable so basically you can plug anything into the transmitter that you could have plugged into your amp (as long as you don't exceed an input level of 6V p-p at the input).

Examples:

Instrument with piezo pickup - If you are currently happy with the sound you get from plugging from your instrument into your amp, then your rig will work just fine substituting Relay for your cable. The input of the Relay transmitter has a very high input impedance (1.3 Mohm) so as not to load down your instrument. This is equal to or even higher than most preamps specifically intended for piezo pickups.

Stereo pickups with Y-Cord - Could also be standard pickups combined with a bridge saddle pickup. Again, if you are happy with the sound you get using this configuration then Relay will not get in the way of your sound. Or you could run each pickup to it's own individual Relay system which could then be split into stereo.

Active instruments w/ preamps - If your instrument has an active preamp and is powered with a single 9v battery you will have no problems using Relay. If you have a double 9v preamp it is theoritically possible to clip the input of the transmitter but unlikely in the real world. Should this actually happen you can remedy it by backing off a bit on the master volume control, adding a pad to the cable or removing one of the batteries. The extra headroom offered by these systems is only a benefit if it fits in with the system gain structure (unless you are using it to purposly clip the input of your amp). Remember, unused headroom is wasted.

Where should I plug Relay into my chain?

Relay replaces the cable from your instrument to wherever the other end of that cable was plugged into. Plug your instrument into the transmitter and plug the output from the receiver into wherever that cable was before. Generally speaking, you are un-tethering yourself from the first piece in your chain. You don't have to worry about gain or level matching as Relay is a "unity" device. That means you get the same level (voltage) at the output jack of the receiver as you are getting from the output of your instrument. Nothing changes ... Relay's output level is neither louder nor softer than the original.

The output from the "tuner" out is exactly the same as the main output in level and impedance. Only difference is the pressing the "mute" button on a G50/90 transmitter shuts off the main out but leaves the tuner output active. The XLR and 1/4" outputs on the G90 are also identical and are provided to give the user more versitility in connecting to other gear.

What IS different?

Depending on how you've set the cable modeling, you could be sending a lot more "highs" into your system than ever before. This could result in more apparent noise or hiss. It would be the same as if you had connected your instrument into your system with a 1-foot cable (which is pretty difficult to do unless you are a contortionist guitarist!). Adjusting to the proper cable model should remedy this situation. On the other hand, if you are using an acoustic guitar leaving the model off will sound like the freshest set of strings you've ever played.

2.4G Wireless FAQ

support@line6.com — Wed, 30 Jun 2010 22:00:30 GMT

Q: Why is the battery meter higher when I restart than when I shut off the transmitter?

A: Line 6 2.4G wireless transmitters have a circuit that measures the actual real-time voltage of the installed batteries and transmits that data to the battery meters in the receivers. The battery meters are very accurate when they have been running continuously since new batteries were installed in the transmitter and the transmitter power has not been cycled on and off. However due to the chemical nature of Alkaline batteries, when they have been shut off, the voltage begins to “rebound “ and the voltage actually increases compared to its value at shutoff. Unfortunately it does not last long and it reverts to true self over twenty minutes or so. For this reason when you first turn on a Transmitter that has been run but allowed to rest the meter will give a high reading that quickly falls over the first few minutes and continues to fall quickly for the first few minutes. This is normal behavior for Alkaline batteries.

Q: Why does my wi-fi slow down when I get my transmitter near my computer?

A: Because wi-fi and Line 6 2.4G wireless products share the same bandwidth some users may experience a slowing down of their wi-fi capabilities when using microphone or instrument transmitters near computers. This is an example of a near/far interference problem and it is heightened because consumer grade wi-fi has very low power. If your Line 6 transmitter gets within 6 feet of your laptop you may witness this situation especially if your wi-fi access point is some distance away. Typically simply moving your Line 6 transmitter farther away from your computer will remedy the situation. Users of Line 6 twelve channel systems should switch their transmitters to the “low power” setting as this will mitigate the problem as well.

Suggested channels settings to avoid interfering with wi-fi

Wi-FI Channel Number	Line 6 Channel Number
1	1, 12
6	2,6
11	5,8,9

Q: What does the Near/Far spec mean to me?

A: The Near/Far interference problem is common to most radio systems and happens when a strong signal captures a receiver making it difficult or impossible for the receiver to decode the weaker signal.

Imagine having a conversation in a quiet room with a person 20 feet away from you. It is likely that you can carry on a conversation with normal voice levels. Now if you move to a noisy environment, with lots of other voices right around your ears it may be very difficult for the conversation to continue with your long distance friend without the both of you shouting.

A similar circumstance occurs with radios and since the long distance transmitter is incapable of increasing its power output it is very likely a very near transmitter may interrupt it.

In the real world this is rarely an unmanageable problem. You should avoid being closer than 3 feet to a receiver that is not on your channel if the intended transmitter is more than 50 feet from this receiver. If this is a regular requirement you will need to remote your antennas (G50, G90 XD-V70).

Relay G50/G90 Series FAQs

support@line6.com — Fri, 23 Apr 2010 23:56:59 GMT

Q: Can I use multiple transmitters with 1 receiver?

A: Yes, you can use multiple transmitters with 1 receiver, however not at the same time on the same channel. The best practice for that type of usage is to have Transmitter A on channel 1 and Transmitter B on channel 2. Then switching the channel on your receiver from channel 1 to channel 2 will toggle which transmitter you will be hearing. You can do this with as many receivers as you have channels, provided each transmitter is on a different channel and you change the channel on your receiver accordingly. You can also set multiple transmitters to one channel, and turn them all off except for the one you'd be using. This way, when you switch instruments, you'd turn off transmitter A on the first instrument, then pick up the next instrument and turn on transmitter B. Just be sure that no one else using a Line 6 wireless system is using the same channel.

Q: Are all Line 6 wireless transmitters and receivers interchangable?

A: Yes, any Line 6 brand wireless transmitter or microphone will work with any Line 6 receiver. It does not matter if they are XD-V or Relay systems, you can mix and match receivers with transmitters and they will work as long as the transmitter and receiver correspond to the same channel.

Q: Is the Relay G5/G90 transmitter compatible with the X2 receiver (or vice versa)?

A: Both systems run in completely different frequency ranges, so they are not interchangeable. However, the X2 and Relay units can be used on the same stage (along with any other analog wireless systems) with no problems.

Q: Where do I get a Relay G50/G90 Series Wireless System?

A: The Relay G50/G90 wireless units are available at all authorized Line 6 dealers. To locate a dealer near you, please see the Line 6 Dealer Finder:

Line 6 Dealer Finder

Q: Where can I purchase replacement Relay G50 transmitters (TBP12) or receivers (RXS12)?

A: Individual transmitters and receivers can be ordered from any Line 6 dealer.

Q: What are the specs on the provided Relay G50 Series power supply?

A: 9V DC, 500mA, center pin negative (2.1mm). See the following link for more power supply FAQs:

Power Supply and Amp Power F.A.Q.

Q: How is the Relay G90 receiver powered?

A: The Relay G90 uses a standard IEC power cable.

Q: Can I use a Voodoo Lab Pedal Power Plus 2 to power the Relay G50 receiver?

A: Yes, but you will need to use the Voodoo lab "current doubler" cable and you will need to use outputs 5 & 6 of the Pedal Power Plus in "normal" position. VooDoo model PPAP.

Q: What type of cable do I need between my guitar & Relay TBP12 transmitter?

A: The Relay G50/G90 Transmitter (TBP12) uses a TA4f to ¼” cable.

Q: What is the pinout for wiring to a TA4F connector?

A: Pin 1 - Gnd

Pin 2 - V+

Pin 3 - Signal

Pin 4 - Z (leave open for instrument)(short to pin 3 for mic)

Q: How many channels does the G50/G90 have? Do they share channels with the G30 system?

A: The G50/G90 have 12 channels, which share the first 6 channels with the G30.

Q: Can I use the TBP12 from a G50 to transmit to a G90 or G30 (or vice versa?)

A: Yes. All 2.4gHz Line 6 transmitters work with all Line 6 2.4gHz receivers to the lowest limitation, channel count, features, etc.

Q: What type of antennas work with the G50 and G90?

G50: ¼ wave antennas, BNC-type connectors; detachable.

G90: ½ wave antennas. The antennas can be detached but RG58-50 ohm radio wire connection is required. Be sure the antennas are not inside a metal case or touching any metal and get your antennas as high as possible.

Q: How long does the pair of AA batteries in the transmitter typically last?

A: 8 hours on high power & 11 hours on low power. If you leave the transmitter cable plugged but turn the power off on the transmitter, there is no battery draw.

Q: How does the battery meter work?

A: The battery meter displays 20 minute increments. Be aware of "alkaline rebound" when turning off the unit and turning it back on, as it may look like it has more power than it really has.

Q: Can I use rechargeable batteries?

A: Yes, but the hours and minutes are calibrated to alkaline batteries so the power reading may be inaccurate. Some rechargables while labeled AA are not true AA size and will not work.

Q: What is the difference between the main output and the tuner output?

A: The only difference is the tuner output still works when the transmitter is muted.

Q: What is different about the Relay G50/G90 system compared to the X2 series?

A: The Relay system works on a higher frequency (2.4 Ghz) and operates on 12 channels rather than 5.

Q: Can the RXR12 Receiver antennas be linked together?

A: Up to 6 receivers can be daisy-chained together. The last unit in the chain should be "terminated" when linking receivers together.

Q: I'm a harmonica player and would like to use the G30 with a bullet microphone (high impedance and high output). Its output peaks at approximately 3V to 4V. Will there be clipping or distortion of the output?

A: No problem with either impedance or input level. The Relay transmitters (TBP06 and TBP12) will handle 6V inputs.

Q: How do I register my Relay G50/G90 System?

Line 6 Product Registration F.A.Q.

Q: What do the different colors states mean on the TBP12 transmitter?

TBP12 LED States:

Blue LED = full

Solid red LED = Low

Flashing red LED = Very Low / Change batteries

Audio LED - Green LED = Audio Signal

Relay G30 Wireless FAQ

support@line6.com — Wed, 29 Jul 2009 16:40:11 GMT

Q: Where do I get a Relay G30 Series Wireless System for use in the US?

A: The Relay G30 is available at all authorized Line 6 dealers. To locate a dealer near you, please see our Dealer Finder.

Q: Where can I purchase replacement Relay G30 transmitters (TBP06) or receivers (RXS06)?

A: You can order them from any authorized dealer.

Q: What are the specs on the provided Relay G30 Series power supply (DC-1G)?

A: 9.6V DC, 500mA, pin center negative. See the following link for more power supply FAQs:

Power Supply and Amp Power F.A.Q.

Q: Can I use a Voodoo Lab Pedal Power Plus 2 to power the Relay G30 receiver?

A: Yes, but you will need to use the Voodoo lab "doubler" cable and you will need to use any two outputs of the Pedal Power Plus set to the "normal" position. See the following link for more information on the "doubler" cable available from Voodoo Lab:

Voodoo Lab cables

Q: What type of cable do I need between my guitar & Relay G30 (TBP06) transmitter?

A: Any mono (tip-sleeve) instrument cable will work for both the instrument to the transmitter and the receiver output. We do not recommend using TRS ("stereo") instrument cables.

Q: If you leave the transmitter cable plugged but turn the power off on the transmitter, does the cable still use up battery life even if the transmitter is powered off? Similar to some analog stomp boxes?

A: When the power is switched off, the audio input has no bearing on battery draw, cable in or out.

Q: Is the Relay G30 (TBP06) transmitter compatible with the X2 receiver (or vice versa)?

A: Both systems run in completely different frequency ranges so they are not compatible with each other, but X2 and Relay units can be used on the same stage (along with any other analog wireless systems) with no problems.

A: No problem with either impedance or input level. The Relay transmitters (TBP06 and TBP12) will handle 6V inputs.

Q: What is the output impedance of the RXS06 Receiver ?

A: The output impedance of the RXS06 Receiver is 200 ohms.

Q: How do I register my Relay G30 System?

A: You can register on your account:

Gear Registration

LED States:

TBP06

BATT:

Blue: On

Red: Low battery

Purple: On channel change

AUDIO:

Green: Signal at input

Orange: On power / channel change.

RXS06

POWER:

Blue: On

AUDIO:

Green: Signal at receiver input

Transmitter Status:

Top: Signal Strength

Bot: Tx Battery Life