Q: How do I access the tuner?
Spider Tuner FAQs
Q: How do I save the Artist/Song presets from the Spider III/IV into the user banks so I can access those presets from my FBV series controller?
A: Hold the desired Channel button (A B C D) for two seconds, then use the four-way arrow selector to choose the bank (number) and location (A, B, C or D) where you want to save the preset to. Select the channel button again, and you will see a rapid flash on the channel light to show the preset has been saved.
Q: How do I operate the "boost" on the Spider series amplifier?
Spider I, II, and III: The Spider Distortion Boost is activated by holding down the “tap tempo” button while rotating the “drive” control above the 12 o'clock position. The B light will illuminate to indicate that the boost is active.
Spider IV: The boost feature can be edited by pressing the presets encoder, then using the right/left function on the four-way arrow selector to select “boost”. You can then activate the feature, increase or decrease the amount of boost (up to 8 db), and select “pre” and/or “post”. This can be activated from the FBV Shortboard MK II by the “fucntion 1” button, and the Effect Loop button the FBV Shortboard (Mk I).
Q: How do I operate the Noise Gate on the Spider series amplifier?
Spider III: Press and hold Tap as you turn the Reverb knob up past twelve o’clock, and you turn on a built-in Noise Gate, which helps to cut down on hiss and noise. When you do this, the Channel D LED comes on to indicate that the Gate is on.
Spider IV: The Noise Gate feature can be edited by pressing the “presets” encoder, then using the right/left function on the four-way arrow selector to select “gate”. You can then choose from “Off”, “Gate”, “Noise Reduction”, or “Gate + Noise Reduction”. Use the up/down arrows to select Threshold and Decay, which are adjustable with the Presets encoder.
Q: Is there a way to control the amount of effect mix repeats the delay effect makes?
Spider I, II, and III: we decided to remove some of the editing capabilities and make it as simple as possible. In addition, we wanted to make it as affordable as possible, and removing some of the edit features was one of the ways that we were able to keep the cost lower. This being the case, you cannot change the delay feedback rate on the Spider.
Spider IV: The delay repeats (feedback) can be edited by pressing the presets encoder, turning to “FX3”, the using the up/down arrows to “FdBk”. You can then increase or decrease the amount of feedback by turning the preset encoder, as well as the delay time and mix.
Q: Every time I switch to a certain amp model the delay comes on - how can I stop this?
Spider I, II, and III: When you select an Amp Model, the Spider automatically sets its tone controls and effects to match that Amp Model. You can disable the auto-FX selection (but not tone control auto-selection), by powering up Spider with the Channel D/Insane button held. Be aware that the auto-selection is re-enabled next time you power up. If you absolutely never want to hear a particular effect (such as delay), you can turn the SmartFX knob to 'Off', then press and hold a channel button until it blinks, and you've saved a new version of the sound, without any effects.
Spider IV: The Auto effect feature can be enabled by pressing the presets encoder, then using the right/left function on the four-way arrow selector to select “autoFX”. You can then activate the feature, as well as turn the tap light on/off and set the timer for the display backlight.
Q: Why does the tap tempo light always blink? Can I turn the tap tempo light off?
Spider I, II, and III 75-150: The tap tempo light shows the tempo of the delay, even if the delay is not active. There is no way to disable the tap tempo light on the Spider I, II, or III Series amplifiers.
Spider IV 75-150: The tap tempo light is assignable to the modulation and delay effects, and shows the tempo of the assigned effect. The tap feature can be enabled by pressing the presets encoder, then using the right/left function on the four-way arrow selector to select your effect, then using the up/down arrow to locate “tap”. The tap feature can be enabled or disabled by turning the “presets” encoder, then using the right/left function on the four-way arrow selector to select”setup”. You can then use the up/down arrows to locate “Taplite”, and de-activate the tap light feature by turning the preset encoder.
Q: Can I connect my Spider series combo amp (i.e. 15, 30, 75, 120) to an external speaker cabinet?
A: No, as there is no external speaker jack to power an external cabinet. The Spider series 150 combo amplifier does have two 8 ohm external speaker outputs that will mute the internal speakers when engaged. See the following link for more cabinet connection information:
Line 6 Head and Cabinet Connections
Q: How can I record direct the Spider series amp signal directly into a computer?
A: You can use the headphone jack as a direct line out to record your Spider series amplifier into any line input on your computer's sound card or audio interface. For sound card connection, you will need a cable with one male stereo 1/4" jack on one end-to plug into the headphone jack of the Spider, and a male 1/8" stereo mini jack-like (the kind on Ipod type headphones) to plug into the sound card. This will work for most computer sound cards, as they often have 1/8" stereo mini inputs and outputs. If you have an audio interface or a professional sound card that have multiple 1/4" inputs, you will need a cable with one male 1/4" TRS (stereo) jack on one end, and two male 1/4" mono jacks on the other end (commonly known as an “insert cable”) to create a stereo image.
Take care in setting the output level on your amp: adjust the master volume to get the cleanest and most noise-free sound when the volume control on the toolbar of your computer is on full, with the volume control on your computer speakers set to normal, reasonable listening levels. If you set the output level on your amp too high, the sound will be undesirably distorted. Set it too low and the sound will be noisy. All you need then is some sort of recording software, of which there are many options available.
Q: Is there a way to use the POD-Style Out (headphone) jack without disabling the speakers?
A: There is no supported way to run both the speakers and the headphone jack at the same time.
Q: Can I use an external effects pedal or processor with a Spider series amplifier?
A: Effects pedals will almost always work well in front of the Spider series amplifiers. Just be certain that the output level of the external effect is not set too high as it could overload the input of the Spider. Most rack-mount processors are designed for line level use and often don't sound quite right when connected to the front of an amplifier.
Q: Can I use a MIDI controller with a Spider amp?
A: The Spider series amplifiers do not have MIDI In or Out connections, but the Spider Valve Mark II does have MIDI jacks. We recommend that you use the correct Line 6 controller with your Spider series amplifier.
Q: Do any of the Spider Series amplifiers have an effects loop?
A: The Spider series (I, II, III, IV) amplifiers are not equipped with an effects loop, but the Spider Valve (I or II) series does have an effect loop.
Q: Can I edit/backup my Spider sounds on my computer?
A: The Spider IV series amplifier can be edited with the Spider IV Edit Software. The previous Spider series (I, II, III) tone editing must be done on the face of the unit, as there is no computer editor for the earlier Spider series. See the following link for more information on the Spider Edit software:
Spider IV Edit (v1.02) FAQs
Q: Which controller will work with my Spider series amp?
Q: Where can I get replacement knobs/speakers/logos for my Spider amplifier?