Categories See All →
- General FAQ
- Computer Based Recording
- Dream Rig
- Live Sound
- Mobile Products
- Legacy Products
- Japanese Support 日本語サポート
Post Flash Update Instructi...
aspiller - May 19 2014 06:12 PM
Spider III factory reset, Presets, and F.A.Q.spider amp reset preset bank artist mode cabinet speaker
Q: What are the presets on my Spider III amplifier?
A: The user presets and artist/song presets for the Spider III are listed as attachments at the bottom of this paragraph. The Spider III user presets are the 36 user-programmable presets. The artist/song presets location cannot be saved, but you can modify and/or store these setting in the 36 user-programmable presets. If you would like to return your unit to the original presets, please perform a factory reset.
spider iii patches.pdf 59.62KB 2152 downloads
Q: How are the Artist preset banks categorization and alphabetized?
A:When looking at the list of the banks in the unit, the banks seem to be broken into four different sections:
1. Albert Lee - Julien K
2. Ash - Volto
3. The Accident Experiment - Thursday
4. Songs 50's - Misc. Fun
Each of the first 3 sections (artist banks) is alphabetized. Is there a reason all the artist presets overall aren't alphabetized?
The artist banks are categorized by Clean, Dirty and Heavy:
1. Albert Lee - Julien K: Cleaner patches
2. Ash - Volto: Midgainy patches
3. The Accident Experiment - Thursday: Heavily overdriven patches
Q: How do I perform a factory reset on my Spider III?
<a href="http://line6.com/com...y/docs/DOC-4499" target="_blank" >Factory Reset Procedures</a>
Q: How do I use the compare mode (to find where the knobs were originally set)?
A: Press and hold the Tap button, then turn the Amp Models knob. This activates Spider III's "Compare mode". Now turn any knob other than Amp Model and Master Volume, and the channel lights
will tell you whether you need to turn that knob up (Channel A lights) or down (Channel D lights) to match the stored setting. The Channel B & C lights will be lit at the same time once the knob position matches the stored setting exactly.
Q: How do I connect the Spider III HD 150 to the Spider Cabinet?
A: The Spider III HD 150 is designed to see a load on *both * speaker outputs by connecting the left and the right inputs to the Spider cabinet with speaker cables. Running the Spider III HD 150 into a 4 ohm load may result in damage to the amplifier. Please see the following link for more information:
<a href="http://line6.com/com...y/docs/DOC-4410" target="_blank" >Cabinet Connection and Ohm F.A.Q</a>
Q: Can I use two Spider III cabinets with the Spider III HD 150?
A:The Spider III HD 150 was designed to power a single Spider III Stereo Cabinet with a stereo 8 ohm load. Using two Spider III cabs would require a modification to each cab so that they are each rewired to produce a 8 ohm mono load. This modification would preferably be done by an authorized Line 6 service center, which can be located from the Service Center link on the Support page.
Q: How do I connect external speakers to my Spider III 150 amplifier?
A: You will need to disconnect the internal speakers (covering the dry-solder clips with electrical tape) and connect both external speaker outputs to an 8 ohm (or higher) load. Do not connect just one side, as this may cause a power amp failure. Powering the internal speakers along with a external speakers may cause a power amp failure and is not supported.
Q: What type of speaker is used on the Spider III combo series?
Spider III 15: Custom 15 (4 ohm)
Spider III 30: Celestion G12E50 (4 ohm)
Spider III 75/150: Celestion G12P80 (8 ohm)
Spider III 120:(2) Celestion G10P80 (8 ohm)