Jump to content


Photo

Line 6 Ux 1 Suddenly Doesnt Work

ux 1 pod farm

  • Please log in to reply
6 replies to this topic

#1 pitowilson

pitowilson

    Just Startin'

  • Members
  • Pip
  • 4 posts

Posted 09 June 2013 - 11:28 AM

Hello !

First of: sorry for my english !!! But I hope you will understand my problem :)

 

I have recorded through Nuendo (used ux 1 as sound card without any simulation) when suddenly everything froze. I rebooted computer a turned pod farm on again a there was no input signal and no output sound. LED was green everything seems allright but no I/O signal.

I tried reboot more time and plug to other usb but still lollipop. Can you help with that?

thanx 


  • 0

#2 Triryche

Triryche

    Uber Guru

  • Line 6 Expert
  • 5067 posts

Posted 10 June 2013 - 05:04 AM

Run the Monkey and make sure you have green ticks for drivers/flash mem, ect...

 

Also, make sure you are selecting Line6 ASIO as your device in Nuendo.

 

Do you have an older red-faced Toneport or a newer black-faced POD Studio?


  • 0

#3 pitowilson

pitowilson

    Just Startin'

  • Members
  • Pip
  • 4 posts

Posted 10 June 2013 - 09:45 AM

Hi, I have the newer versiom, I ran the monkey the pod farm 2 wasn´t in green but I updated it , but still no sound.

I was in the middle of recording session in nuendo so the I/O in ASIO was set good. Its no sound or input signal just trough the UX.


  • 0

#4 pitowilson

pitowilson

    Just Startin'

  • Members
  • Pip
  • 4 posts

Posted 15 June 2013 - 10:36 AM

Run the Monkey and make sure you have green ticks for drivers/flash mem, ect...

 

Also, make sure you are selecting Line6 ASIO as your device in Nuendo.

 

Do you have an older red-faced Toneport or a newer black-faced POD Studio?

Hi, I have the newer versiom, I ran the monkey the pod farm 2 wasn´t in green but I updated it , but still no sound.

I was in the middle of recording session in nuendo so the I/O in ASIO was set good. Its no sound or input signal just trough the UX.


  • 0

#5 silverhead

silverhead

    Uber Guru

  • Line 6 Expert
  • 11444 posts
  • LocationOttawa, Ontario, Canada

Posted 15 June 2013 - 02:53 PM

I would run Line 6 monkey and reinstall the UX1 driver and firmware.


  • 0

Life is what happens to you while you're busy making other plans.
.... John Lennon

 

 


#6 pitowilson

pitowilson

    Just Startin'

  • Members
  • Pip
  • 4 posts

Posted 15 June 2013 - 11:51 PM

I would run Line 6 monkey and reinstall the UX1 driver and firmware.

I already did it but its still same. I tried install it on 3 different PC but stil no sound


  • 0

#7 silverhead

silverhead

    Uber Guru

  • Line 6 Expert
  • 11444 posts
  • LocationOttawa, Ontario, Canada

Posted 16 June 2013 - 04:42 AM

I suggest you open a support ticket to work directly with Line 6 tech support.

 

http://line6.com/sup...ickets/add.html


  • 0

Life is what happens to you while you're busy making other plans.
.... John Lennon

 

 






Also tagged with one or more of these keywords: ux 1, pod farm

0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users