There are some less pretty ways that I can get around this, like making multiple presets of the same effect or to make a dummy preset that is called between calling the same preset again, but these all ruin the flux by changing the settings instantly.

My wishes/suggestions:

• That the HX One will ignore the PC command if the currently loaded preset is called again and nothing is changed.
• If something has changed: Reload the preset.
• The ability to actively change the flux setting to high or low instead of just toggling.

Another question:

How long does it take to load a preset? I tried making a series of commands to my amp and the HX One where the preset will be loaded and flux being toggled immediately afterwards. I didn't get it to work when doing it as a series of commands, but I could select the preset and then toggle flux.

i have a GigRig G3s controlling 3 midi pedals: channel 1 is an H9, channel 2 is a Jackson audio golden boy, and channel 3 is my new HX one. They are daisy chained G3>HX1>H9>Gb purely due to cables and pedal board layout.

i have changed the global settings of the HX1 to be channel 3 and midi thru obvs. 
 

All midi commands (pc and cc) work as intended to the H9 and GB meaning the cabling works,  and the HX1 is sending midi commands onwards via midi thru.

I have set a patch up to toggle the HX1 on/off using a cc command on channel 3 which also works fine.

Here is the thing- I can’t figure out why the pc commands don’t work on the HX1 because they do on the other pedals. This is where I am at.

I have hx user presets saved at 000 and 001 in the HX1 and when I load the G3 preset (call it number 1) which contains the midi pc command 00, it fails to load 000. In fact, nothing happens on the HX1 but the other pedals respond. (The G3 can send up to 20 midi messages per G3 preset so effectively you just program in as many as you need). On the adjacent G3 preset (call that G3 number 2), I check and the toggle on off works. I go back to the G3 preset number 1, again, th epic message does work. Next I go into the midi menu in G3 preset 1 and I change the pc from 000 to 001. And then when I exit the menu, it executes the pc message and the HXone switches to 001. I then play about a bit more (change the HX one sound and go to totally different G3 preset) and when I go back to G3 preset 1 which now contains  HX1 preset 001, it is unresponsive. I then repeat the exercise, amend the midi message back to pc 00 and on exit from the midi menu, it triggers the HX One again which accepts the pc change back to preset 000

So it appears I have narrowed it down to either:

1. Fault on the G3 which appears to be sending the midi message on exit of the menu only but I rule that out as the other pedals work as intended with pc messages

2. Fault on the HX one which fails to recognise the pc change

3. User error and set up issue

the HX one is brand new and updated to 3.81

Belp very much appreciated!

Video: https://streamable.com/cwj2kv

I am using two external buttons to scroll up and down through the presets.

For the sake of argument, let's imagine I am only using one effect type, PolyPitch.

I can have several presets with various settings saved, but for all of them the display will simply show "PolyPitch" and not my custom Preset Name.

All the different sounds are indistingushable when labeled that way and the only way to navigate is to try them by ear.

This is catastrophic and renders the unit useless for me...

(I realize, that the list view is the intended way to do it, but with external footswitches it practically doubles the amount of clicks needed to operate the unit).

It gets worse! To see the Preset Name at all I have to enter the list view by pressing both footswitches.

Both footswitches are also needed to access the tuner. It is very easy for one footswitch to slip while holding both of them in order to access the tuner - the pedal will then either enter the list mode or activate a preset.

I also wish there was a way to cue the presets with external footswitches from the single effect view.

External footswitches would scrool through presets and the built-in ON footswitch would activate it.

Those behaviours are native to other Helix products and as a seasoned HX Stomp user I can't wrap my head around this not being implemented in HX ONE, especially because of the small form factor.

Best,

Janko

I have a CIOKS DC5 and was thinking of pairing the 300+100ma outputs to feed the HX One with 400ma.

According the FAQs that should work but I feel like it's on the edge.. Any gotchas like pitch shifting actually requires more than 400ma?

I have a Vox AC15 without an effects loop, so my entire pedal chain goes straight into the amp’s input. Ever since I added the Line 6 HX One, my guitar volume has dropped dramatically—even when no effect is selected and it’s bypassed.

I’ve tried tweaking input/output levels and impedance settings, but nothing helps; the signal stays way too quiet compared to before. Any ideas on what to check or fix? Thanks!

I just got a HX-one and am using it in 4-cable method. I've noticed that when using it in this configuration, the tuner mute seems to only mute the final output of the HX (i.e. the signal is still output to the "loop" even when in tuner mute mode, despite the manual stating that when tuner audio setting is selected to "mute" that "all output is muted").

Is there a way around this? And/or could the next firmware update include a fix or option here so that all output (final output and the loop) is muted when tuner mute is active?

For context - I'm using it in an FX chain with multiple DI/signal takeoff points within the chain, and would appreciate if hte tuner muted everything (at the moment, if I have a DI in the loop then this signal won't be muted when I step on the tuner).

Thanks :)

I remember that on my Helix, holding down the third encoder during power-up would show the serial number.

Is there anything similar for the HX One?

Thanks so much for your help!

I have observed the following behaviour for some time and only just now been able to replicate the issue consistently.

Scenario 1: When moving from a PolyWham effect preset with the status ‘off’ to Feedbacker effect preset status ‘on’ or ‘off’ results in feedbacker effect not triggering. Toggling the HX One On/Off device footswitch while on the feedbacker preset in this scenario does not correct the feedbacker issue.

Scenario 2: When moving from PolyWham effect preset status ‘on’ to Feedbacker effect status ‘on’ or ‘off’ results in results in feedbacker effect working as expected. Toggling the HX One On/Off device footswitch while on the feedbacker preset in this scenario also works as expected.

This issue is occurring whether presets are navigated view Prev/Next midi command or by the in-built footswitch preset navigation.

The same observations occur when moving from the PolyCapo effect to Feedbacker so it may be related to moving from pitcher shifting effects?

This issue does not appear to occur if moving from another effect such as Dynamic Plate, Tube Comp 3 Note Generator to the Feedbacker effect.

It also appears that if scrolling past another effect between PolyWham  and Feedbacker resolves this issue e.g. if a had 3 presets in the sequential order PolyWham > Dynamic Plate > Feedbacker the issue is not observed when scrolling past between PolyWham to Feedbacker using the preset scroll function.

It seems like the pitch shifting (PolyWham/PolyCapo) effect preset status is being passed on the feedbacker effect when navigating directly between the two irrespective of the saved Feedbacker preset status.

Has anyone else had the same experience or can replicate this behaviour?

Hope some one can help - I have an HX one with latest firmware and when set to true bypass has absolutely no sound when disengaged. Fine on DSP bypass though.  Google suggests this could be expected behaviour but that doesn't sound right to me.  Any help would be appreciated!

Cheers

Paul

My board consists of an HX One connected to the input of my HX Stomp, with a Nano Cortex in the HXS fx loop, and a Pirate Midi Bridge 4 to switch presets in all three devices. When i switch presets in the HX One, there is an audible gap.

Have any of you noticed this too? I assume that there is no user solution to this, and that the only hope would be if Line 6 could fix it with a firmware update (which there hasn’t been in a long time).

Thoughts?

This is my first post and I've bought a 2nd hand HX One.

I'm unable to select effects. When the unit is turned on it displays the selected preset. If I push the Home button once it goes into the adjustments for that effect. Sometimes the effect I'm looking to select flashes in the screen for a fraction of a second.

Pushing and turning the Effect knob allows me to go to the category and effect I want but the original preset keeps returning to the display. Pushing the Effect knob to select just results in the preset returning.

It may be me I know but something doesn't seem right.

Peter

I'm running a GigRig G3 and it would be great to be able to assign a footswitch to "preset up/down"

The locked up rotary knobs are similar to the same-effect-loading-midi-issue described in the other thread.  

I have no hopes on anybody from Line 6 to actually fix this issue based on previous lack of response on issues related to HX One, but I wanted to describe the issue to the community.   I gather support of HX One is even less now that they released a bunch of new flagship products.  It's a great pedal with a good interface when it works.  

Maybe others have had similar problems to this?  

How feasible is this cabling, and is it even possible?

Guitar —> HX One In

HX One Send —> Comp —> OD —> Pod In

Pod Out —> HX One Return

HX One Out —> FRFR

Using the Post position, I get to use the HX One as the first effect in the chain. In Pre, I get to have the HX One running last (reverb, etc.). Am I understanding this right?

Thank you very much for your help.

just got a HX_One and I really like it, but there's one thing that bothers me: When I load a delay, I want the right switch as tap control. With not time based FX I want the Flux. I tried to save that within the preset, but it doesn't work. Do I miss something in the general settings or is it really not possible?

When I send PC message to hx one to change the preset, the knobs works it well.

However, if I send the same PC message again, the knobs become unresponsive and turning them has no change.

Are there someone who has same issue?

The thing with the EFX LE is the amount of taps out of the analog tap out and MTC is linked together with the options of 1 bar, 2 bars, Continuously (Persistent). I have to set it 1 or 2 bars as persistent is making the DIG crazy. The problem with that is the HX one tap blinks blue and with the correct BPM for 1 bar or 2 bars (4 taps or 8 taps) but then revert back to red blinks and reset to preset BPM. Is there a way for the HX one to keep the 4 or 8 taps it's getting and not revert back to preset/global BPM? It's seems that it only takes MTC when it's getting continuous MTC.

Any help would be much appreciated.

Thanks !  Joe

I have a Hx Effects on my pedalboard where I wanted to replace an older plastic volume pedal with a Mission Engineering Expression Pedal, the Mission Engineering EP1-L6-BK.

Did connect it but it‘s not really working, there is nothing between 0% or 100%. As soon as ai release a bit from 0% it goes to 100%. Did try different settings and also connected it directly to the Hx Effects. It‘s connected by an oridnary stereo cable.

Any advice ?

If I push and hold right foot switch, it turns into tap tempo mode and red led is blinking.
How can i get into flux mode?

But I cannot find that effect on my HX one.

Where can I find feedbacker effect?

Current connections:

-TRS going out of the Send of the Stomp.

-The split ends are then going (ring) into L/mono of the HX One, and the other (tip) is going into the R/return of the HX One.

-I'm taking one regular cable from each output of the HX One, back into the HX Stomp return/aux ins (L out to L return, R out to R return, etc.)

Relevant settings on the HX One (I've had to use these to even get close, changing any of these makes the rest of the things worse):

-I/O Config - Insert

-Insert Position - Pre

-Bypass Type - DSP

-Tuner Audio - Mute

There are a variety of issues I'm having but I'll try to outline a specific one here, and perhaps it might lead to other answers.

-I call up something like the Poly Capo on the HX One (a pitch shifting effect like this makes it easier to hear the problems described below...)

-I then go back to the Stomp and:

--(1) I use a Stereo FX L/R block at the start of the chain, but when I engage the HX One, I ALWAYS get an equal amount of dry signal, in addition to the shifted signal from the Poly Capo.  **BUT, when I engage the tuner on the HX One, it registers a signal for tuning...while constantly sending the dry tone (non-shifted) through as well (even with every setting everywhere telling the tuner to mute...)

--(2) same hookup as above.  This time I use a Mono FX Loop L block on the Stomp.  This will kill the dry signal I was getting from the previous attempt, so the Poly Capo then is behaving like it should...BUT when I engage the tuner on the HX One, it doesn't register any signal at all!

--(3) same hookup as above. This time I use a Mono FX Loop R block on the Stomp.  Now, it completely ignores the Poly Capo (on or off, it doesn't affect the tone) BUT it does register the signal for the tuner AND keeps it going so you can hear it when the tuner is engaged.

So, in this configuration, I can never have the Poly Capo effect work the way it's supposed to, while also having the tuner work (again, point (2) makes the effect work properly, but nothing ever makes the tuner work correctly...)

Then, I tried reversing the inputs (tip/ring) going into the HX One.  (This mostly made things worse)

--This time using FX Loop L, kills all signal completely whenever that block is on in the Stomp...but does register when the tuner is engaged (but still no signal coming through).

--Then, trying the FX Loop R, has no signal like above but this time the tuner doesn't register anything either...so this is the farthest away from working of all the attempts.

-If I turn OFF that block in the Stomp, effectively bypassing the FX Loop completely, I get signal coming back through the rest of the chain.

So, in summary, it does seem like the (ring) needs to go to the L/Mono input of the HX One, with the (tip) in the R/return, but as you can see from above, there's still something that isn't quite working.  Any help with this would be greatly appreciated!!!

With the dunlop Mini X, I have this problem: when i push on th dunlop i never reach the max position, it goes up when pushing and at the middle it goes down. I can't find solution on manuals. Is it incompatibility beetwen hx one and Mini X ? or do I miss a setting somewhere ?

Thanks

HX One is set to insert and It's cabled like so.

Gtr. ---->>  hx one  left/mono input
Right (return) input -----> >  iridium.        mono out
Left/mono out ---->>    iridium input
Right out(send) ------>>  to DAW

1)no effects from the hx one are heard. 2)No iridium sounds are heard

3) hx effects are heard if set to stereo

4) Iridium seems bypassed in all scenarios.

I am missing something but but I am not understanding what it is.

Thoughts?

I've been using Alexander Pedals (rewind and space force) that also have the possibility of transitioning between different settings of the same preset, which on the One is called flux.

But I can choose between momentary or latch on the Alexander pedals.

Is there a possibilty of setting it up that way on the One also? (I'm not talking about setting the flux time to zero, but actual momentary setting).

Also, it would be nice to have some longer flux transitioning times, for example 30 seconds, for ambient stuff that would be perfect.

Thanks for yoour time and cheerio!

Thanks.

Is there a MIDI CC+Val I'm missing that will select the preset from preset list? 

Thank you!

Very much enjoying my HX One, particularly the delay effects. However I'm having a problem with one of the biggest reasons I bought it - pitch and capo effects. Whenever I use any of the polypitch algorithms (but not , the pedal loses about 10-20 db in volume. I've tried tweaking the input impedence, and tried using the pedal in mono vs. stereo, and nothing seems to do it. I also turn the boost up (when available) by 6db and it still doesn't get back to unity/level it is with the pedal turned off or taken out of the chain.  I've tried using it in my pedal chain (isolated loop switcher) and on its own with just guitar into pedal and then onto amp, happens with both.

Any ideas what this could be?

I have an HX one and I recently upgraded to the new 3.71 firmware and my pedal started crashing. When I rotate thru the modulation effects and I get to an effect called 122 Rotary, it makes a weird noise and freezes and only a power cycle brings it back.  I tried everything including factory reset, but it keeps crashing. It seems that some other effects are also working weird, but I can't really tell. Any ideas what could this be?

Thanks!

LEo.