I have just seen that POD GOs appear good price on the SH market and wondering what people think about it in terms of how it sounds. I fully understand has less flexibility that Helix, less routing options but I think all of those options are above my level anyway.

Does anyone have experiences of the Wireless version also, is there any reduced quality level of the wireless signal for the inbuilt version compared to what I already have which is the external Relay G10s?     Thanks 

can you pleas give an answer to this question.

POD Go Edit 2.50 is designed for INTEL processors. When it will available for Apple chips?

Thank you.

Best regards

Michael

Please advise.

With the H2Midi Pro (which I thought was the solution I needed), I have tried connecting the Podgo to both the Usb-c (device) port, and the Usb-A host port. Connected to either one, I don't see activity lights when I change a preset. I'm guessing that's my problem, but then what do I connect to Podgo to, to get all this to work.

I want to send some midi signals to another pedal from the pod go. Is that possible ? I know midi in is possible but how about midi out to other devices ?

For instance : i have a pod go pedal and a big sky reverb pedal. Whenever i change presets (or snapshot) on the pod go, i'd like to send some midi signals to the big sky so that it loads a specific preset on it.
I don't want to hit some switch on the pod and then having to hit some switch on the big sky.

Is this possible?

Line 6 HX Stomp Multi-Effects Guitar Pedal

https://www.amazon.com/Line-Electric-Guitar-HX-Stomp/dp/B07J2LV1N

Line 6 POD Go Guitar Multi-Effects Pedal, Black
https://www.amazon.com/Line-POD-Go-Guitar-Multi-Effects/dp/B0835QQM1

But, at this point, I am unable to make a decision based on which one is better for me and require your expert advice.

As per my application, I require a robust multi-effects processor for my guitar recording sessions, practice, and occasional live performances. The product must offer good amp simulation, realistic tone generation, ease of editing, and consistent performance.

Which one do you recommend that I purchase?

Should I always be outputting at 0 db to reduce the hum?  (at a significant loss of volume)

Should I use a different IR?

Should each effect be limited to 0 dB?

Is my POD GO defective?

Of course, reducing the volume, reduces the hum  How do you keep the hum down without sacrificing volume? 

I have found a couple other topics on this but no resolution.

also. My signal was cutting in and out even after his guitar was put through the wired setting. 
 

is there a way for us both to use our wireless set ups in the same vicinity? 

image.jpgimage.jpg

I'm trying to use my POD Go as to re-amp.

I have installed the latest version of Pod go edit and the ASIO drivers 2.5 (i'm using win11), I have selected "input 3/4" in my patch on the pod;

I'm using reaper and connecting it using ASIO on the pod go in 44khz, 24bits; the pod go sound card seems to be up and running.

I'm am then sending one track to hardware output 3 and nothing happens.

I have 2 other tracks armed on inputs 1 and 3, hoping to see, the DI on 1 and the re-amped signal on 3, but nothing, no sound.

I have no idea what i'm doing wrong, i have installed and reinstalled the drivers multiple times, i dont know what else to do ?

Thanks,

I have the Pod go and i have a surface Pro with windows 11. When i conect the pod go i have the message "no divice connected" in the Pod go edit software.

I check in the Administrator drives control from windows and show me that there is a problem with the drivers of the Pod go

I've tried to change the cable, reintall the drivers.... nothing is working.

Waiting for an anwser

Thank you

I have been interested in the possibility of sending my guitar signal through my Pod Go and to separate, external bass and guitar cabinets. I know the Pod Go doesn't have the ability to split the signal. Could I utilize a separate signal splitting pedal, or could I use the stereo outputs on the Pod Go to send the signal to two cabs simultaneously? Thanks!

So I've had my line 6 Pod Go for about 4 days now and liking it. However when I try and connect it to PODgo Edit all I get is "no device connected". Even though my computer happily picks it up as a sound card and I've already done 2 recordings with it using my DAW and all works fine. But it just won't connect to the Edit program!!!

I'm trying to use V1.11, I've uninstalled it about 10 times , downloaded the installer again and re installed it but everytime is still the same. I've tried every USB slot my computer has and makes no difference, I just don't get it. 

All drivers are installed and working perfectly, I'm using it as my permeant interface now, but I can not connect to pod edit! Which really will hinder my device in the future as I won't be able to do firmware updates or load IRs! 

Makes no sense that the computer finds it fine and it's being used as my audio interface and to record with! Using windows 10. Any help would be greatly appreciated. 

Thank You. 

I am trying to get a good acoustic sound on the pod go, but I do not currently own a preamp. I am running an LR Baggs M1A active acoustic pickup straight into the pod go and don't want to have to crank the pickup's volume to the max. Every preamp I've tried so far on the pod go distorts the sound at the volume I want. Is there any way to get a clean sound, or do I have to get an acoustic preamp?

wenn ich meinen Pod Go Wireless über USB an den PC anschließe, kann ich am Editor arbeiten und die Sounds verändern. Allerdings höre ich nichts über die angeschlossenen Lautsprecher (auch keine Youtube Videos oder andere Audiofiles). Kann mir jemand helfen?

Gruß, Klaus.

Guitar in to Pro input. Fx out to Ed Sheeran Looper X (instrument level) input. Looper Amp out to Pro Fx Return. Main Pro outs to twin Marshall full stacks via the front instrument in.

I put the FX Mono loop right before the amp on the Pro chain. (Speaker box off).

On the looper X. I also have a keyboard input into a ¼ in. Looper input. (As well as two mics.)

My problems are two fold. When I put the Fx Icon in front of the amp icon, I seem to loose some level of the other enabled effects, before it, in the chain. Also, the keyboard has some “added” unwanted effects, like reverb and/or delay! Any recommendations? Thx. In advance, Dan,

I’ve been wondering for a while, why doesn’t the POD Go have the feedbacker block?

I imagine the reason might be DSP limitations.

I wonder if a lighter version has been taken into consideration.

A mini feedbacker with fewer controls, without the Trigger and Re-trigger options to give one example.

It would be better than nothing, that’s for sure!

I totally understand that portability comes with trade-offs, but I feel like a feedbacker would be a great addition, it really helps create that fuller “amp in a box” experience.

Thanks,
Lando

merci pour vos réponses

Looking for some advice for the Pod Go.

What I've been hearing is that if you use a Pod Go with an amp, you need to turn off your amp and IR in the patches, otherwise, if you don't, the two will clash and not give you a good sound.

So, when I do perform live, we have no amps on stage, go direct to the mix and use in ear monitors. And the unit sounds good. But ... when I'm at home setting up presets and trying out tones, the sound never come out the way I want, and I just take my chance it'll sound good live.

Currently I have a Spider V 20 in the practice room (all the other amps I had I gave away when I moved as we couldn't take everything with us)

So, the long story short ... some have suggested using powered speakers or on stage monitors or a PA system for setting up presets and hearing what you've created without the muddling of an amp.

Can anyone recommend one of the three over an amp, or an amp with super clean sound that won't compete with the Pod.

Thanks for any responses

Anyway, I just got the Pod Express Bass and I'm having a blast playing with it -- it will definitely join my live rig shortly.

I'm hoping the folks here are pretty familiar with it and can help me with some questions:

1. Is there any way to stop the effects from resetting every time I start up the machine?  For example, in the Mutant synth, I will probably never want it in Band Pass mode, only Low Pass.  So, I change it to Low Pass in the app, and that's great, but if I leave and come back, it's set to band pass again.
2. Other than Studio and Punch, the rest of the built-in Amps are pretty distorted, like they have a distortion effect on.  I can reduce the gain the get rid of some of that, but then when I go back to that amp, I have to adjust the gain again.  Am I just doing something wrong?
3. In the Android app, let's say I'm on preset 12 and I start fiddling with the sound, and I find another great sound, but I don't want to save it over preset 12, I want to put it on a new preset.  Is there any way to do that from within the app, or do I have to press down the Amp knob, rotate it somewhere, and press again to save?
4. Is there a difference between the Channel Volume setting and the little thumb wheel, when thumb wheel is set to control all volumes?  That is, are they independent volume controls?
5. When setting the Gain, Bass, etc., is there a technique to use where I can adjust that without also modifying the effect on that knob when I let go of the Alt key?
6. Is the noise gate part of a preset?  When does it get reset?
7. Has anyone put together a cheat sheet that has all the button shortcuts?  For example, Alt-Tap-Comp to set the gate level, etc.?

Thanks! I may have more questions -- I've only had this since Saturday...

After a factory reset, the built-in expression pedal does not work. 

What I tried: Global settings/Exp 1 + 2: Position = Global. 

Any suggestions?

I was messing with some of the presets looking for tones and I hit something and the only thing the A,B,C,D buttons due is turn effects off and on. I am assuming that I am in snapshot mode. So I hit the two up and down buttons at the same time to hopefully exit the snapshot mode, but it seems I can't get out of snapshot mode....My patches are in my user and I can no longer access my patche A, B,C, D. Any help would be appreciated.

I wanted to share my global EQ settings and would be interested in hearing your brutally honest, but not unkind, feedback.

Currently I use the PodGo through the front of a Deluxe Reverb or through the effects return of the 1st generation Catalyst 60 in manual mode.  The PodGO output is set to Line in the global settings for the Catalyst.

As I struggle getting tones that I like with the amp models, my goal is to use the PodGo strictly as a effects when I want, without useing any amp models or cabs.

I did the "jailbreak" on some patches to remove the amp and cab blocks which opened up blocks to add more effects blocks (within available DSP).

I am by no means an advanced user and have used up my patience trying to dial in tones on amps and cabs.  Anyway....let me know what you all think (if you care to try my global EQ settings).

Cheers,

Alfred

Low Cut: 53 Hz

High Cut: 2.5kHz

Low Peak

Freq:  83 Hz

Q:  0.1

Gain:  +8.4dB

Mid Peak

Freq:  305 Hz

Q:  0.6

Gain:  -7.1dB

High Peak

Freq:  2.0 k Hz

Q:  0.7

Gain:  +9.5dB

My name is Rob and I have a developmental disability which makes it difficult for me to learn from video tutorials. I just purchased a pod go and I'm having a really hard time understanding how it works. Would anyone be willing to spend a few minutes with me by Zoom or Google Meet just to walk me through the basics. I'm more than willing to pay using Venmo or PayPal for your time. I contacted Line 6 Customer Service, and they referred me to more videos, and told me they don't do any on-line tutoring. Any help will be greatly appreciated. 

When switching between presets 1-7, the indicator shows the correct position, but in red. It really should be white since that's the color used for presets 1-7 when in preset mode (not FX mode). To me, this is a pretty good indication that something is going wrong under the hood.

Additionally, the LED ring doesn't update at all for presets 8-21. It gets stuck in the position of the last preset, and the color remains red. So, if I move up from preset 7 -> 8, the LED stays red in position 7. If I move down from preset 1 -> 21, it stays red in position 1. If I press the switches enough times to get back to 1-7, the LED starts updating again.

When I have it connected to POD Express Edit on my computer, I can see the presets changing as I press FS3/4 all the way from 1-21, so I know the switches are working despite the LED not updating properly.

I was wondering if there's some kind of FX that is like the kind of electronic violin swell (I know it's a Midi guitar, but one can try to approximate) that sometimes Allan uses on his leads

Even how to achieve an auto swell would be interesting (without using the expression pedal)

Do you guys have any idea?

Or at least an fx which I should try to exploit?

Thanks

Now, in green letters at the bottom of the PodGo Edit screen it says "Updates Available" so I thought I'd try that. A window does appear but it says"the following updates are available for" PodGo Edit 2.0 and for Pod Go Firmware 2.1.

Again, I'm trying to load Edit and Firmware for 2.5.

Never had an issue before. What's wrong?

I have a problems with Line6 POD GO updates.

I am trying to update the latest firmware for it, but there is at the moment showing only starting screen (red edges with black center) in normal startup.

The red edges with black screen is the same figure which is showing first always when you start the POD Go by normally.

But now it is stuck in this screen.

So, I have tried to manually update it with Line6 Updater and Line 6 Central in offline mode.

Also tried with online mode, but always the update stops for error message.

Original firmware is 1.30.0 and I have tried to update it for 1.10, 1.40, 2.01 and 2.50 but always the same error message which tells that update fails.

Tried factory reset with key combination C and D pushed down when powering on but nothing happened.

So, what can I try to do that I can fix this problem ?

Just wondering if it is possible to change the name of the preset lists?

I don't need the factory presets and would like to change the name of the list ... not a major issue at all, but can't really figure out if this is possible.

Thanks!

Having issues with the bottom part of the display ( photos ).

Any ideas for solving this?

Thanks. -

I use Pod Go for two ways. The first is when I connect an external expression pedal to EXP2 for volume control and use the built-in pedal for wah. The second is to use simply Pod Go only, in which case I do not use wah. This varies depending on the gig.
My external expression pedal is an Ernie Ball VP Junior. This pedal is technically a volume pedal, but it can be used as an expression pedal by connecting a cable to the OUT jack.
The issue is that this pedal uses an “A-curve pot (logarithmic),” so if the volume curve setting on the effect edit page is set to logarithmic, the volume changes become too sudden (logarithmic x logarithmic!). Setting the volume curve to linear resolves the issue, but when not using an external pedal this is undesirable as the built-in volume pedal's curve is “B-curve (linear)”
 

If there were a function to specify the volume curve of an external expression pedal in the global settings, the issue would be completely resolved. There is a function called EXP1/2 Polarity, and this new EXP2 Curve function can be placed near the Polarity function.  
Adding this function would expand the choices for external pedals.

thanks.

Fiddling with the dial on the left side of the POD Express doesn't balance the volume when the pedal is Off with when it is On. When the pedal is on, it's got plenty of volume. When the pedal is switched Off, it's way too quiet.

Thanks,

TimC