tochiro

Hi, Can the M20D be controlled with an Android tablet via wifi? Cheers

Yes radatats, I did what you suggested and it's working well enough for my needs. Thank you for your help!

@radatats Good idea! I tried it but there's a problem because if I set the screamer (number 2) ON and I set its output to 0 then there's no sound. @TheRealZap I cannot because my HD500X is in F5-F8 mode.

I noticed that the problem happens after the M20D has been on for a few hours.

Hi, I programmed a preset with various pedals and use 3 different types of sounds with it: 1 - a clean sound with no pedals 2 - a dirt sound by engaging 2 pedals 3 - a metal sound by disengaging the previous 2 pedals and engaging 2 others I press on a footswitch for number 2, then I have to quickly press on it again to turn it off and press on another footswitch for number 3. This is difficult because there's no time between sounds 2 and 3. Is it possible to avoid that and when I press for sound 3 it engages pedals for number 3 and disengage pedals of number 2 at the same time? Thank you for your help. Cheers

I'm in France and we are on tour now until late August. I will then bring the M20D to the music shop where I bought it.

Hi, I noticed that sometimes the lower right corner of the display seems faulty because the icons appear "broken". It's not the hardware, it's the way the screen is displayed. I have to change screen (from Monitor to Perform for instance) to update the display and it's back to normal, until next time... It happens a few times per concert. I have the latest firmware. Any ideas? Cheers

We had a gig yesterday evening and I noticed the problem happens randomly. I recalled a setup and scene I created at home but this time the Doubler level was very high in the monitors although I'm sure it was at 0 when I saved the scene/setup. So it seems the 4 FXs have that problem. Please L6 could you correct the bug quickly now?

Yes me too I have to recall the setup and the scene every time after switching on the M20D to avoid the problem. But it should not be like that.

On a side note, that's a mistake IMO. My acoustic guitar is direct and I have a big feedback problem. I had to change preset.

I plug in to 5 and 6 inputs using TRSs and I finally found a stereo preset I tweaked to my liking.

I finally applied another stereo preset with FBS and tweaked it. I couldn't find the previously saved preset for my acoustic (Deep Tweak preset).

Ok I've found the stereo mic and applied it but there's no FBS. I also wanted to recall the preset I previously saved for my acoustic (Deep Tweak preset) but can't find it when I click on Load Preset...

Hi, My acoustic guitar uses 2 inputs of the M20D because I apply a stereo effect on it with a pedal. I'd like to use a stereo preset to group those 2 inputs but need the FBS because the guitar is prone to feedback. I cannot find any such preset in the M20D... What can I do? Thank you for your help. Cheers

The thing I really don't like on the POD is the ODs and distortions. I did the same comparison with my amps and pedals and the pedals sound much better for OD and distortion.

I've used an HD500 on stage for 2 years and there's just one thing I don't quite like with it - The OD and distortion FXs.

I've just updated my 2 L3m through my M20D. It's a long process (about 20 minutes) but everything went well. I did not notice any change in the sound but that's normal as far as I understand it.

Is the update also applicable to the L3m?

Yes exactly.

The HD500X does not sound good into a Vox AC15C1 either. Even without amp sim and no pedals at all, it colors the sound of the Vox (more treble, less mid).

No and this is the point of the thread. Monitor levels are not recalled but setups. Also I don't see why you would need to change a scene during a song... That seems to me quite secondary compared to the advantage of having a single action to do to save/recall ALL the parameters.

It's confusing to have 2 saving procedures. One with both Scene and Setup is enough since you can name it and have as many as you need.

That should be more simple. And that means every time I switch the M20D on I have to recall the last opened scene. What have Setups AND Scenes? One of them is enough to call all the parameters.

Many M20Ds have the same bug.

What is Line6 waiting to correct that bug?