Please ensure Javascript is enabled for purposes of website accessibility Jump to content

nkrcompany

Members
  • Posts

    7
  • Joined

  • Last visited

Posts posted by nkrcompany

  1. On 2/13/2022 at 7:51 PM, lucilanga said:

    All right. So, yeah, I went back downgrading the FW,  it seems they "broke" CC51, CC52 .. etc behavior in 3.10. But looking at 3.10 release info I found this:

     

    
    Bank/Preset/Snapshot Up and Down messages how properly work via incoming FS1/FS7 emulation MIDI messages 

    and

    
    New MIDI message (Helix Floor/Rack/LT/HX Stomp XL): CC71 engages the MODE switch 

     

    So I guess the behavior is intentional. I suspect Board/Floor/LT are in the same boat.

    I wish they update the manual manual more often. Even on version F there is no mention of CC71, let alone the new 3.15 stuff CC77-81.

    I just tried using CC71 with my Helix Rack. I would like to report that my problem has been solved.

    After sending a CC71 with value 0, I can send CC49-58 to control footswitches bypass state.

    However CC71 values are completely missing from Helix manual, so here it is (from HX Stomp manual):

    CC71
    Values: 0-5
    Footswitch Mode (0=Stomp, 1=Scroll, 2=Preset, 3=Snapshot, 4=Next footswitch mode, 5=Previous footswitch mode)

    • Thanks 1
  2. On 2/13/2022 at 7:51 PM, lucilanga said:

    All right. So, yeah, I went back downgrading the FW,  it seems they "broke" CC51, CC52 .. etc behavior in 3.10. But looking at 3.10 release info I found this:

     

    
    Bank/Preset/Snapshot Up and Down messages how properly work via incoming FS1/FS7 emulation MIDI messages 

    and

    
    New MIDI message (Helix Floor/Rack/LT/HX Stomp XL): CC71 engages the MODE switch 

     

    So I guess the behavior is intentional. I suspect Board/Floor/LT are in the same boat.

    I wish they update the manual manual more often. Even on version F there is no mention of CC71, let alone the new 3.15 stuff CC77-81.

     

    Thanks, I'll check CC71 operation with my Helix Rack. Yeah, it would be great to get updated midi manual with version updates.

  3. I'm using a Helix rack, just updated to 3.15 firmware (and made a factory reset too).

    I'm using a midi controller and regularly use MIDI CC51, CC52, CC53, or CC54 messages to emulate footswitch operation. Unfortunately Helix Rack does not respond as expected. 

    I don't know what version made this bug, but it guess it was present since 3.0. That's sure this bug was present in the preceding 3.11

     

    In HX Edit I linked Footswitch 3-7 to turn on/off individual effects. So on the bypass/controller assign panel I made four setup for the individual blocks, setting parameter to Bypass, and Source the Footswitch 3-7. Now, when I send these CCs to Helix Rack sometimes it doesn't respond, sometimes it makes a preset change instead of turning on/off the individual effect blocks. Earlier this worked great and without problems.

     

    I really would like to use these footswitch CCs, can you please to help to resolve this issue?

  4. Thank you, I've found this earlier. However it's quite expensive and I'm in Europe. And the I really don't need a full bridge, as my saddles, block and electronics are in great condition. Only the knife edges have problems. It would be great if I could buy only the tremolo base plate. Have you got any info if it is possible the find only the base plate? Do you think that, Tylerguitars.com could help with james tyler bridge replacement parts?

  5. Hi All,

     

    I've a nice black JTV69, I bought it in 2011. Since then I use it almost every day. However I noticed that after some tremolo usage the guitar goes out of tune all the time. During the last string change I checked the tremolo bridge and I noticed that the knife edges seems to be really used. I took some pictures, please check them:

    https://drive.google.com/open?id=1AXxGWGxaZdf9hsxSTbhWW_76lOyLjxGO

    The problem is that, I really don't know what should I do now, because this type of bridge is very special and I cannot buy a new one in the local music stores. I found one on fullcompass but its quite expensive and I really don't need new saddles and tremolo block etc. Only the bridge plate with the kinfe edges.

    Have you got any idea how should I repair it? Have you got any experience about bad/used kinfe edges on JTV69 guitars?

     

    Thank you in advance!

    Norbert

  6. Hi All!

     

    I would like to integrate my Pod HD pro with an Eleven Rack similar to 4CM. I would like to make the best connection thats possible to leave the tone crystal clear.

    I would like to use the stereo FX loop and the balanced output of the POD.

    I bought a few TRS patch cable, but there is some problem with it as its noisy.

    I really need some technical information about the FX Loop specification to solve this problem.

    Are these FX loop jacks TRS balanced outputs/inputs, or TS jacks? I didn't find informations in the manual about this.

    Please help

    Thanks

    Norbert

×
×
  • Create New...