52dmk

On 1/5/2023 at 1:26 PM, H1GHLVND3R said:

Yea, i do.

Maybe try a different 3.5mm to 6.3mm convertor, or a pair of headphones with a 6.3mm plug that won't need to be converted 

On 1/5/2023 at 12:54 PM, H1GHLVND3R said:

Did reset Global setting to factory, still no progress. Tried use old Heads, same problem

Are you using a 3.5mm to 6.3mm convertor for your headphones? I've had more than a few of these do strange things

Also finding same behaviour with 4-Voice Chorus

Bug in 3.5 FlexoVibe.

Rate parameter does not have option to change to note subdivision in HX edit, but can press knob on Helix floor to change Rate to note subdivision. This then breaks link between HX edit and Helix floor, with changes made to Rate on HX edit not affecting Rate on Helix floor, and changes made to Rate parameter not changing knob position in HX edit.

Pressing Rate knob on Helxi floor returns Rate to numbered speed and allows HX edit to control Rate parameter again.

Same behaviour occurs for mono and stereo versions.

Could due to that pedal model having 22k impedance. Try setting the impedance manually to 1M instead of auto

On 4/26/2022 at 3:58 PM, MayPRS said:

 

Thanks for the reply. Channel volume. Do you think I need to adjust the FX loop volumes?

You could try changing the loop level selector on AC30? What's it set at now?

Are you turning up the channel volume or master volume? 

If you're turning up the channel volume, you're increasing the signal that gets send out of the FX loop and probably distorting the HXFX return with a signal that's too hot.

If you're turning up the master, you're probably running out of clean headroom in the power amp section of the AC30 and clipping there.

Sounds like a ground loop.

I used to get the same using 4CM with a Marshall 6100.

Solved it buy buying an ebtech (also Morley?) hum eliminator and putting it between the Helix send and the amps input.

I had similar problems a while ago.

I use Logic X on MBPro, with Helix floor. I also use an RME babyface interface. In Logic my input device was Helix and output Babyface, as I just prefer using the volume control on the Babyface for monitors and headphones (the dim function is really useful).

I was having a similar issue as you, where initially everything would be great, then after an arbitrary amount of time, a huge amount of latency (2-3 seconds) would appear out of nowhere. Unplugging/rebooting either interface fixed the problem, but only temporarily.

The fix, for me anyway, was to create an aggregate device, with Helix in and Babyface out. Since using this, I've not had a single repeat of the problem!

Anyone noticed the Alpaca Rouge High Cut control works backwards?

The more high cut you dial in, the less is applied.

On 4/23/2020 at 5:55 PM, 52dmk said:

Just to add to the Tap Tempo issue;

There's also an issue with the bpm display on tap button showing the correct bpm.

 

In the video below, i'm connected to a helix floor with usb and running HX edit.

I tap in the tempo in HX edit (which is registered correctly and changes the bpm for fx using bpm), however this is not displayed in the tap scribble bpm until i touch the footswitch (touch, not press).

 

Tap video

 

Not sure if it helps debugging at all, or if it's a separate issue.

 

Sorry to say this still happens in 2.91.

Could someone else try to replicate this, please?

Go to Global Settings > Displays > Set Tempo BPM Display to Persistent

Tapped tempo bpm (on floor unit, or in HX edit) does not update the displayed bpm until you touch the tap switch (not press, just touch).

It does update FX using bpm fine now, just not the display.

Just to add to the Tap Tempo issue;

There's also an issue with the bpm display on tap button showing the correct bpm.

In the video below, i'm connected to a helix floor with usb and running HX edit.

I tap in the tempo in HX edit (which is registered correctly and changes the bpm for fx using bpm), however this is not displayed in the tap scribble bpm until i touch the footswitch (touch, not press).

Tap video

Not sure if it helps debugging at all, or if it's a separate issue.

1 minute ago, EdwinV said:

Not familiar with this drive, but I find it quite noisy. Tried it with the new Revv amp model. Am I doing something wrong?

Try it with something lower gain, it's got loads of gain all on its own. Maybe a edge of breakup ac30 or plexi style amp.

Absolutely blown away by this!

1 minute ago, SaschaFranck said:

How could such an obvious thing such as the tap tempo madness slip through in testing?

One wrong or missing character in code is all it would take.

9 minutes ago, pinetrax said:

Well, step temple seems to be working for some of you and not for some of you, Maybe the problem is the combination of different amps and affects along with the delays you have, try a new preset with just the delays and see if they don't work

Tried with a blank preset, a single simple delay, problem is still there.

I don't think problem is with delays, as they work fine when manually set, or if you manually set the bpm.

The issue is with the tap tempo being significantly out in its calculated bpm.

Tap tempo is definitely not working correctly.

If I tap along to a 135bpm metronome the tapped bpm is around 160bpm.

If I set helix bpm manually, it's fine.

1 hour ago, unperfectcircle said:

yes, exactly.

I need the LFO to start from the beginning of the sweep as soon as I activate the relative snapshot.

 

I tried with Native demo (I don’t own a HX Effects yet, I’m gathering this information to see if I can pull the trigger or not considering my needs), but I can’t find a way to achieve this easily.

 

Touching the tap tempo button or sending a CC from another machine are not viable options in my case.

Thanks a lot

I tried it last night; doesn't look like this has been implemented in Helix.

Might be a good one to suggest on ideascale?

You mean restart the LFO?

I've got a filter pro rack, and to restart the LFO you pressed the tap tempo button once (or the midi cc connected).

Not tried it on the helix, but this might be what you're after?