Search the Community
Showing results for tags 'frozen'.
Found 6 results
Flashing Tone lights, Amplifi Frozen
pianojunky posted a topic in AMPLIFiWas updating the firmware last night when my iPad suddenly crashed, went to the boot screen with the apple logo and restarted. Since then my amplifi has been a complete brick. When I turn it on all 4 tone lights flash continuously. If I try to restore the amp to factory settings, the lights all light up solid. I can't use anything, Bluetooth won't work, volume knob won't work, guitar won't work. Anyone have any suggestions?! Desperate here because I am supposed to record all day tomorrow.
rakerley25 posted a topic in AMPLIFiSo, I bought this new Amplify 75 amp and upon trying to update the firmware, it appears I put the unit in Return-to-Sender mode. I have not been able to get this unit to respond. I tried everything mentioned in the support forum. I even went out and bought a USB cable. I even tried three different devices in an effort to update the amp. No luck. I just keep getting blinking lights on the amp. So, my question is, who in the world thought this was a good idea to manufacture something this finicky? This thing is going back to Amazon in the morning. I dont have time or patience to deal with something that should be so simple. Insert cord, attached guitar and play some music. Simple as that. I guess simplicity totally by passed the folks at Line6 because this is a freaking nightmare.
Line6Tony posted a article in Firehawk FXQ: The ABCD lights are flashing and the unit does not function, even after a factory reset. A: This is recovery mode, meaning there was a failed update attempt. The unit will function again once the update is successfully completed. In the event of a failed update, power up while holding A/C and retry the update using the Line 6 Updater found at www.line6.com/software. If the update fails repeatedly, you likely need to try the process on a different computer. Q: I'm seeing the "Load error 21" error message OR the A/D lights are solid and the unit is non-responsive. A: These situations are likely caused by corrupt tones. If you find yourself in one of these "bad tone" situations, you should follow the steps below get to a fresh state: o Copy your User tones to My Tones (backed up in the cloud) or share them with the other options offered by the app so that they're backed up o Forget the Bluetooth connection o Reset the unit ( hold Master volume + tap while powering up) o (Re)install the v1.10 firmware, which resolved many patch and Bluetooth issues o Uninstall the app o Power cycle mobile device o Install latest version of app o Pair to Firehawk Load user patches one by one, testing each one along the way, to find the bad patch. It would be great if you can tell us if you find a bad patch you found on our cloud so we can test it and/or eliminate it. Q: What can I do if I am experiencing Bluetooth connectivity issues between my Bluetooth device and the FIREHAWK FX? A: Make sure you are using the latest firmware and app. For other troubleshooting steps about Bluetooth connectivity and usage, check out our Bluetooth Connectivity FAQ HERE. Q: What should I do If I am experiencing connection issues with the FIREHAWK FX Remote app when I switch back and forth between apps on my iOS device? A: An important thing to note about the FIREHAWK FX Remote app functionality is that in addition to the iOS Bluetooth connection between your FIREHAWK FX and your iOS device, there is a secondary 'sync' connection between the amp and the app. Each time you minimize/close the app, the connection between the FIREHAWK FX Remote app and the FIREHAWK FX will need to be re-established, even if your iOS device is reporting that the FIREHAWK FX is connected via 'Bluetooth'. In this case, re-opening the FIREHAWK FX Remote app will automatically re-establish the connection within a few seconds. Make sure to look at the main menu of the FIREHAWK FX Remote app and wait for it to indicate that your FIREHAWK FX is 'connected' before moving forward using the app. If it does not automatically re-connect, close the FIREHAWK FX Remote app by double-tapping your iOS home key, then sliding the FIREHAWK FX Remote app window up and off the screen. Relaunch the FIREHAWK FX Remote app and it should re-sync itself with the FIREHAWK FX. Android devices usually have a function that lists all open programs where you can slide the app left or right to close it. Relaunch the FIREHAWK FX Remote app and it should re-sync itself with the hardware.
Recovery from corrupt tones / A and D lights lock-up
Line6Tony posted a article in Firehawk FXWe've found that tones created while using the original 1.01 firmware can sometimes be corrupted, regardless if they are new or downloaded tones. This results in the device locking up, with a factory reset being needed for recovery (press and hold the Master Volume knob and the TAP button as you power up the unit). Firmwares at version 1.10 or later resolves this issue. Tones created in version 1.10 or later can no longer be corrupted like they would have under version 1.01. However, corrupted tones created in version 1.01 are still problematic when used in Firehawks updated to later firmware versions. We encourage those encountering this issue to update to the latest firmware via the Line 6 Updater software, then perform a factory reset. Please note that any tones not backed up to My Tones prior to a reset will be lost (corrupted tones cannot be uploaded because they crash the unit and thus can't be selected for uploading).
FX100 Upgrade Stuck (USB 3.0, no progress)
GutturalMan posted a topic in AMPLIFiHello! Upgrading my Amplifi fx100 to 2.10.00, first time (from 1.01.0). Installed Utility, plugged it in USB 3.0 port (Windows 7 64 bit). Launched in firmware update mode. Pressed Next in the update utility. Seeing "Update In Progress. Do not turn off or unplug your device at this time". Progress bar is empty and it's saying "Installing firmware update...". One hour passed with no changes. How to cancel/retry upgrade process without a risk of having entirely broken device?
Amp Head Frozen
closwrayth posted a topic in Vettahey i need some help in figuring out whats going on with my amp. i bought it recently from a pawn shop and i am determined in ressurecting it to full function. if oyu can shoot me a reply or email me @ email@example.com. here is a video of my problem: http://www.youtube.com/watch?v=kYB03I1zPxg