Search the Community
Showing results for tags 'g10'.
-
Hi, My g10 is no longer working. I have had a search but can't find any conclusive answers. When I try to charge, the base unit is just flashing a steady red ring. The transmitter is showing no signs of life at all. I have tried updating to all the latest firmware, but no improvment. Anything I can do? Cheers,
-
Lithium Ion (L-Ion) rechargeable batteries are a very common technology employed in many consumer electronics. The below suggested best practices and general information will help you achieve the maximum battery performance over the product’s expected lifetime. The typical estimated life of a L-Ion battery is 300-500 charge cycles (fully charged-fully discharged-fully recharged) or 2-3 years, whichever occurs first. L-Ion batteries will slowly discharge when not in use. Do not leave batteries unused for extended periods of time, neither in storage nor in the product. When a battery has been unused for 6 months, charge or dispose of the battery based on charge status. Rechargeable L-Ion batteries have a limited life and will irreversibly and gradually lose their capacity to hold a charge. Run time decreases as the battery loses capacity. Elevated temperatures can cause permanent loss capacity and negatively impacts the cycle life. Whenever possible, keep L-Ion batteries in cool conditions to preserve the capacity of the cells.
-
hey line 6, any news on new firmware to the g10 cuz after the update, all 3 of my g10 dont last more than 45 min in use... then it dies... before this update the battery life was easely more than 4 hours... any chance we get the old firmware at least ? so those of us that never had any problems with overheating or stuff like that can still use the g10, or is it time to throw it to tha garbage and get a boss wireless system?
-
Corrective Action required immediately for Relay G10, Relay G10S, and Relay G10T wireless products purchased prior to March 2020. Several instances of extreme overheating and a risk of fire presented by the Relay G10T wireless transmitter have been reported since the product was introduced in 2016. All instances of overheating reportedly occurred during charging. In March 2020, Line 6 issued a “recall-to-repair” with the U.S. Consumer Product Safety Commission. The recall to repair is designed to prevent overheating and the risk of fire, and simply requires users to install a firmware update. It takes about five minutes to complete this process. Many users have still not updated their units so this Safety Alert is intended to raise awareness of the issue and urge owners who have not yet done so to be sure they have the latest firmware version. The latest G10T firmware version is 1.06. Please be sure to update your transmitter if you are not on this latest version. Additionally, and not a safety matter, Line 6 has determined that certain Relay G10T units with the earlier versions of the firmware may not charge optimally within warm environments. The latest firmware version also corrects this issue. Units sold after March 2020 were already updated to the latest version and require no update. However, if you own a Relay G10 purchased before then, and have not updated the firmware, please immediately update your unit to prevent the risk of overheating. Step-by-step instructions are provided through the links below. INSTRUCTIONS FOR UPDATING G10 & G10S INSTRUCTIONS FOR UPDATING G10T VIA SPIDER V AMPS INSTRUCTIONS FOR UPDATING G10T VIA YAMAHA THR-II Additionally, the Line 6 Relay G10T USB Charging Cable (an optional accessory not included with Relay G10, Relay G10S, or Relay G10T), which may be used to connect a G10T transmitter to a powered USB port, can also contribute to extreme overheating in the transmitter. The Relay G10T USB Charging Cable cannot be repaired and the concern cannot be remedied by a firmware update to other Relay G10 products. If you purchased a Relay G10T USB Charging Cable, please discontinue using it. Owners of the cable who provide satisfactory proof of its destruction will receive a refund. INSTRUCTIONS FOR RECEIVING USB CABLE REFUND Please contact Customer Service if you require additional assistance: Online: https://line6.com/company/contact/ Phone: 877-865-4636 Text: 818-699-9480
-
Hi - I recently bought a Spider V60 mkii and am looking to get a wireless transmitter. I wondered if any other transmitters other than the GT10T will work with the internal transceiver built into the amp. I know that is the recommended one and supported one, but wondered whether others will also work
-
My Relay G10 had been working just fine with my Spider V 60 prior to updating the firmware but I decided I should update the firmware as the urgent notices was instructing me to do. So I did and now my Relay G10 will not charge! I trusted Line 6 and the firmware and now it has rendered my Relay useless. Not impressed. Anyone else experiencing this issue?
-
Desplázate hacia abajo para ver las instrucciones en español. Faites défiler la page vers le bas pour trouver des instructions en français. Anweisungen auf Deutsch finden Sie weiter unten. Per le istruzioni in Italiano scorrete verso il basso. Overview: For those who have access to a Spider V (MKI or MKII) amp and wish to update the G10T Transmitter, it must be done in the order shown below (first update the amp, then the G10). We strongly suggest updating the amp with the latest version of the Line 6 Updater from a desktop/laptop computer, even though it is possible to update the amp from a mobile device. Video Tutorial: Updating a Relay-Ready Spider V Amp and G10T Transmitter With a Mac Computer Video Tutorial: Updating a Relay-Ready Spider V Amp and G10T Transmitter With a Windows Computer I. Update the Spider V Amp Firmware With a Computer First, (for Windows users) download and install the Spider V drivers Go to Line6.com and click on "Support" Select "Downloads" and set the three pulldown windows under "Free Software Downloads" to: [Spider V 60], [Line 6 Drivers], [your PC OS] Click "GO" The page will update with the Line 6 drivers for the Spider V. Click 'GET DOWNLOAD' to download the driver installer to your computer. Log in to your free Line 6 User account (or create a new account) Click on 'ACCEPT AND DOWNLOAD' and follow the instructions to save the driver installer When the installer has been downloaded, double-click on it and follow the instructions to install it in your computer Next, download and install the Line 6 Updater for Spider V Go to Line6.com and click on "Support" Select "Downloads" and set the three pulldown windows under"Free Software Downloads" to: [spider V 30], [Line 6 Updater], [your Mac or PC OS] Click "GO" The page will update with the Line 6 Updater for the Spider V. Click 'GET DOWNLOAD' to download the updater program to your computer. Click on 'ACCEPT AND DOWNLOAD' and follow the instructions to save the updater installer When the program has been downloaded, double-click on it and follow the instructions to install it in your computer Lastly, update the Spider V amp Connect the Spider V’s USB port to your computer with a traditional USB cable Slide the "SELECT" switch to the USB port labeled Mac/PC Turn the amp on Open the Line 6 Updater application and sign in with your Line 6 User Account Click on the Spider V amp Click the “Update” button next to the latest firmware version at the top Follow the prompts to begin the update process Do not turn off or unplug your Spider V or computer during the update Watch for the update status to be completed on the Spider V LCD. Once completed, the amp will restart. Disconnect and reconnect the USB cable, then repeat the process for the G10T Transmitter Note: If you experience a failed update or your amp locks up during boot up, you can hold down the Amp and FX buttons to enter Update Mode. Once it's in Update Mode, attempt the update procedure again. II. Update the G10T Firmware with the Spider V Amp Make sure the Spider V amp is still connected to the computer, and that the computer is still connected to the internet Insert the G10T all the way into the Spider's Input jack Ensure that the "SELECT" switch is still engaged with the USB port labeled "Mac/PC". Turn on your Spider amp if it's off. Run the Line 6 Updater program. Sign in to your Line 6 User Account. Click on “Relay G10T” Click the “Update” button next to the latest firmware version. Follow the prompts to begin the update process. Important: Do not turn off or unplug your Spider V amp or computer during the update. The Updater will say the amp is resetting, but take note of the amp's display, as it will continue updating, ultimately showing "Part 1 of 1 100% Updating Transmttr". The amp will reset itself, ending the update process. Cómo actualizar el firmware del transmisor G10 mediante los amplificadores Spider V Descripción general: Aquellos usuarios que dispongan de un amplificador Spider V (MKI o MKII) y deseen actualizar el transmisor G10T, el proceso debe realizarse en el orden indicado a continuación (primero actualizar el amplificador y luego el G10). Recomendamos encarecidamente actualizar el amplificador con la última versión del Line 6 Updater desde un ordenador de sobremesa/portátil, aunque puede hacerse desde un dispositivo móvil. Tutorial en vídeo: Actualizar un transmisor G10T y un amplificador Spider V compatible con Relay con un ordenador Mac Tutorial en vídeo: Actualizar un transmisor G10T y un amplificador Spider V compatible con Relay con un ordenador Windows I. Actualizar el firmware del amplificador Spider V con un ordenador En primer lugar, (para usuarios de Windows) descarga e instala los controladores del Spider V Visita Line6.com y haz clic en [Soporte] Selecciona “Downloads” y, en las tres ventanas desplegables de “Free Software Downloads”, selecciona “Spider V 60”, “Line 6 Drivers”, “el sistema operativo de tu PC”. Haz clic en [GO]. La página se actualizará con los controladores de Line 6 para el Spider V. Haz clic en [GET DOWNLOAD] para descargar el instalador del controlador en tu ordenador. Inicia sesión en tu cuenta de usuario gratuita de Line 6 (o bien crea una cuenta nueva). Haz clic en [ACCEPT AND DOWNLOAD] y sigue las instrucciones para guardar el instalador del controlador. Una vez descargado el instalador, haz doble clic en él y sigue las instrucciones para instalarlo en tu ordenador. A continuación, descarga e instala el Line 6 Updater para Spider V Visita Line6.com y haz clic en [Soporte]. Selecciona “Downloads” y, en las tres ventanas desplegables de “Free Software Downloads”, selecciona “Spider V 30”, “Line 6 Updater”, “el sistema operativo de tu Mac o PC”. Haz clic en [GO]. La página se actualizará con el actualizador Line 6 para el Spider V. Haz clic en [GET DOWNLOAD] para descargar el programa del actualización en tu ordenador. Haz clic en [ACCEPT AND DOWNLOAD] y sigue las instrucciones para guardar el instalador del actualizador. Una vez descargado el programa, haz doble clic en él y sigue las instrucciones para instalarlo en tu ordenador. Por último, actualiza el amplificador Spider V Conecta el puerto USB del Spider V a tu ordenador con un cable USB tradicional. Desliza el conmutador SELECT hasta el puerto USB marcado como Mac/PC. Activa el amplificador. Abre la aplicación Line 6 Updater e inicia sesión con tu cuenta de usuario de Line 6. Haz clic en el amplificador Spider V. Haz clic en el botón [Update] situado junto a la última versión del firmware en la parte superior. Sigue las instrucciones para empezar el proceso de actualización. No desactives ni desconectes tu Spider V ni el ordenador durante la actualización. Consulta el estado de la actualización en la pantalla LCD de Spider V. Una vez completada, el amplificador se reiniciará. Desconecta y vuelve a conectar el cable USB; a continuación, repite el proceso para el transmisor G10T. Nota: Si falla la actualización o si tu amplificador se bloquea durante el arranque, puedes mantener pulsados los botones AMP y FX para entrar en el modo Update. Una vez en el modo Update, intenta realizar nuevamente el procedimiento de actualización. II. Actualizar el firmware del G10T con el amplificador Spider V Comprueba que el amplificador Spider V sigue conectado al ordenador y que éste sigue conectado a Internet. Inserta totalmente el G10T en el jack de entrada del Spider. Comprueba que el conmutador SELECT sigue conectado al puerto USB marcado como “Mac/PC”. Activa el amplificador Spider si está desactivado. Ejecuta el programa Line 6 Updater. Inicia sesión en tu cuenta de usuario de Line 6. Haz clic en [Relay G10T]. Haz clic en el botón [Update] situado junto a la última versión del firmware. Sigue las instrucciones para empezar el proceso de actualización. Importante: No desactives ni desconectes tu amplificador Spider V ni el ordenador durante la actualización. El Updater notificará que el amplificador se está reiniciando, pero observa la pantalla del amplificador, ya que continuará actualizándose y, al final, mostrará “Part 1 of 1 100% Updating Transmttr”. El amplificador se reiniciará, finalizando el proceso de actualización. Mise à jour du système de l’émetteur G10 via les amplis Spider V Aperçu: Si vous disposez d’un ampli Spider V (MKI ou MKII) et souhaitez mettre l’émetteur G10T à jour, suivez impérativement l’ordre indiqué ci-dessous (mise à jour de l’ampli avant celle du G10). Nous recommandons vivement de mettre l’ampli à jour avec la dernière version de l’application Line 6 Updater à partir d’un ordinateur fixe ou portable même s’il est possible de le faire à partir d’un dispositif mobile. Tutoriel vidéo: Mise à jour d’un ampli Spider V compatible Relay et d’un émetteur G10T avec un ordinateur Mac Tutoriel vidéo: Mise à jour d’un ampli Spider V compatible Relay et d’un émetteur G10T avec un ordinateur Windows I. Mise à jour du système de l’ampli Spider V avec un ordinateur (Pour utilisateurs Windows) Commencez par télécharger et installer les pilotes Spider V. Rendez-vous sur Line6.com et cliquez sur [Assistance]. Sélectionnez «Downloads» et réglez les trois menus déroulants sous «Free Software Downloads» sur «Spider V 60», «Line 6 Drivers», «le système de votre ordinateur». Cliquez sur [GO]. La page affiche les pilotes Line 6 pour le Spider V. Cliquez sur [GET DOWNLOAD] pour télécharger l’installeur de pilote sur votre ordinateur. Connectez-vous à votre compte utilisateur Line 6 gratuit (ou créez un compte). Cliquez sur [ACCEPT AND DOWNLOAD] et suivez les instructions pour sauvegarder l’installeur de pilote. Quand l’installeur est téléchargé, double-cliquez dessus et suivez les instructions pour l’installer sur votre ordinateur. Ensuite, téléchargez et installez l’application Line 6 Updater pour Spider V. Rendez-vous sur Line6.com et cliquez sur [Assistance]. Sélectionnez «Downloads» et réglez les trois menus déroulants sous «Free Software Downloads» sur «Spider V 30», «Line 6 Updater», «votre système Mac ou PC». Cliquez sur [GO]. La page affiche l’application Line 6 Updater pour le Spider V. Cliquez sur [GET DOWNLOAD] pour télécharger l’application de mise à jour sur votre ordinateur. Cliquez sur [ACCEPT AND DOWNLOAD] et suivez les instructions pour sauvegarder l’installeur de l’Updater. Quand le programme a été téléchargé, double-cliquez dessus et suivez les instructions pour l’installer sur votre ordinateur. Pour finir, mettez l’ampli Spider V à jour Branchez la prise USB du Spider V à votre ordinateur avec un câble USB conventionnel. Faites glisser le commutateur SELECT sur le port USB Mac/PC. Mettez l’ampli sous tension. Ouvrez l’application Line 6 Updater et identifiez-vous avec votre compte utilisateur Line 6. Cliquez sur l’ampli Spider V. Cliquez sur le bouton [Update] à côté de la version la plus récente du système en tête de liste. Suivez les instructions pour lancer la mise à jour. N’éteignez pas et ne débranchez pas le Spider V ou l’ordinateur durant la mise à jour. Surveillez l’évolution de la mise à jour sur l’écran LCD du Spider V. A la fin, l’ampli redémarre. Débranchez et rebranchez le câble USB puis recommencez l’opération pour l’émetteur G10T. Remarque: Si la mise à jour échoue ou si votre ampli se bloque durant le redémarrage, maintenez les boutons AMP et FX enfoncés pour passer en mode Update. Une fois en mode Update, recommencez la procédure de mise à jour. II. Mise à jour du système du G10T avec l’ampli Spider V Vérifiez que l’ampli Spider V est toujours connecté à l’ordinateur et que l’ordinateur est toujours connecté à internet. Insérez le G10T à fond dans la prise Input du Spider. Vérifiez que le commutateur SELECT est toujours réglé sur le port USB Mac/PC. Allumez l’ampli Spider s’il est éteint. Lancez l’application Line 6 Updater. Identifiez-vous avec votre compte utilisateur Line 6. Cliquez sur [Relay G10T]. Cliquez sur le bouton [Update] à côté de la version la plus récente du système. Suivez les instructions pour lancer la mise à jour. Important: N’éteignez pas et ne débranchez pas le Spider V ou l’ordinateur durant la mise à jour. L’Updater signale que l’ampli se réinitialise mais surveillez l’écran de l’ampli qui finira par afficher «Part 1 of 1 100% Updating Transmttr». L’ampli se réinitialise alors, concluant ainsi la mise à jour. Firmware-Aktualisierung des G10-Senders mit einem Spider V-Verstärker Vorweg: Wer Zugriff auf einen Spider V (MKI oder MKII) Verstärker hat und seinen G10T-Sender aktualisieren möchte, muss in der nachfolgend beschriebenen Reihenfolge vorgehen (erst der Amp, dann der G10). Wir möchten Ihnen ans Herz legen, den Verstärker mit der aktuellen Line 6 Updater-Version von einem Computer/Laptop aus zu aktualisieren, wenngleich dies auch mit einem Mobilgerät möglich ist. Video-Tutorial: Aktualisieren eines Relay-fähigen Spider V-Verstärkers und des G10T-Senders mit einem Mac-Computer Video-Tutorial: Aktualisieren eines Relay-fähigen Spider V-Verstärkers und des G10T-Senders mit einem Windows-Computer I. Aktualisieren der Spider V-Verstärker-Firmware mit einem Computer (Für Windows-Anwender:) Laden Sie sich die Spider V-Treiber herunter und installieren Sie sie Surfen Sie zu Line6.com und klicken Sie auf [Support]. Wählen Sie “Downloads” und mit den drei Listenfenstern unter “Free Software Downloads” zunächst “Spider V 60”, dann “Line 6 Drivers” und Ihr Computer-Betriebssystem. Klicken Sie auf [GO]. Jetzt werden die Line 6-Treiber für die Spider V-Amps angezeigt. Klicken Sie auf [GET DOWNLOAD], um sich den Treiber herunterzuladen. Loggen Sie sich in Ihr Line 6-Benutzerkonto ein (oder legen Sie sich ein Konto an). Klicken Sie auf [ACCEPT AND DOWNLOAD] und befolgen Sie die Hinweise zum Sichern des Installationsprogramms. Doppelklicken Sie auf das heruntergeladene Installationsprogramm und befolgen Sie die Hinweise für die Installation auf dem Rechner. Laden Sie sich jetzt den “Line 6 Updater” für den Spider V herunter Surfen Sie zu Line6.com und klicken Sie auf [Support]. Wählen Sie “Downloads” und mit den drei Listenfenstern unter “Free Software Downloads” zunächst “Spider V 30”, dann “Line 6 Updater” und Ihr Computer-Betriebssystem. Klicken Sie auf [GO]. Jetzt werden die Line 6 Updater-Treiber für die Spider V-Amps angezeigt. Klicken Sie auf [GET DOWNLOAD], um sich das Updater-Programm herunterzuladen. Klicken Sie auf [ACCEPT AND DOWNLOAD] und befolgen Sie die Hinweise zum Sichern des Updaters. Doppelklicken Sie auf das heruntergeladene Programm und befolgen Sie die Hinweise für die Installation auf dem Rechner. Aktualisieren Sie Ihren Spider V-Verstärker Schließen Sie den USB-Port des Spider V mit einem geeigneten Kabel an den Computer an. Schieben Sie den SELECT-Schalter zum USB-Port mit der Beschriftung “Mac/PC”. Schalten Sie den Verstärker ein. Öffnen Sie den “Line 6 Updater” und loggen Sie sich in Ihr Line 6-Konto ein. Klicken Sie auf [Spider V]. Klicken Sie auf den [Update]-Button neben der aktuellen Firmware-Version (ganz oben). Befolgen Sie die Anweisungen, um die Aktualisierung zu starten. Schalten Sie den Spider V bzw. Computer bei laufender Aktualisierung nicht aus und lösen Sie nie die Verbindung. Das LC-Display des Spider V informiert über den Fortgang der Aktualisierung. Am Ende des Vorgangs wird der Amp neu gestartet. Lösen Sie die USB-Verbindung und Wiederholen Sie den Vorgang für den G10T-Sender. Anmerkung: Wenn die Aktualisierung fehlschlägt oder der Verstärker beim Hochfahren hängen bleibt, können Sie den AMP- und FX-Taster gedrückt halten, um in den Update-Modus zu wechseln. Wiederholen Sie die Aktualisierung im Update-Modus noch einmal. II. Aktualisieren der G10T-Firmware mit dem Spider V-Verstärker Der Spider V-Verstärker muss noch mit dem Computer verbunden sein – und der Rechner muss einen Internetzugang haben. Schieben Sie den G10T komplett in die INPUT-Buchse des Spider. Schieben Sie den SELECT-Schalter zum USB-Port namens “Mac/PC”. Schalten Sie den Spider-Verstärker bei Bedarf ein. Starten Sie “Line 6 Updater”. Loggen Sie sich in Ihr Line 6-Benutzerkonto ein. Klicken Sie auf [Relay G10T]. Klicken Sie auf den [Update]-Button neben der aktuellen Firmware-Version. Befolgen Sie die Anweisungen, um die Aktualisierung zu starten. Wichtig: Schalten Sie den Spider V bzw. Computer bei laufender Aktualisierung nicht aus und lösen Sie nie die Verbindung. Der “Updater” zeigt an, dass der Verstärker zurückgestellt wird. Im Display des Amps wird der Fortgang der Aktualisierung angezeigt und wenig später “Part 1 of 1 100% Updating Transmttr”. Der Verstärker wird schließlich zurückgestellt – die Aktualisierung ist beendet. Come Aggiornare il Firmware del Trasmettitore G10 tramite Amplificatori Spider V Panoramica: Coloro che hanno a disposizione un ampli Spider V (MKI o MKII) e vogliono aggiornare il Trasmettitore G10T, dovranno farlo seguendo l’ordine indicato qui di seguito (prima aggiornare l’ampli, poi il G10) Sebbene sia possibile farlo anche da dispositivo mobile, vi consigliamo vivamente di aggiornare l’ampli con l’ultima versione del Line 6 Updater da un computer desktop/laptop. Tutorial Video: Aggiornare un Ampli Spider V Relay-Ready e un Trasmettitore G10T Con un Computer Mac Tutorial Video: Aggiornare un Ampli Spider V Relay-Ready e un Trasmettitore G10T Con un Computer Windows I. Aggiornare il firmware di un Ampli Spider V Con un Computer Prima di tutto, (per utenti Windows) scaricate e installate i driver dello Spider V Andate su Line6.com e cliccate su [Support] Scegliete “Downloads” e selezionate nei tre menu a discesa di “Free Software Downloads” “Spider V 60”, “Line 6 Drivers” e “sistema operativo del vostro PC”. Cliccate [GO]. La pagina si aggiornerà con i driver Line 6 per lo Spider V. Cliccate [GET DOWNLOAD] per scaricare sul vostro computer l’installer del driver. Loggatevi con il vostro account gratuito Line 6 (o create un nuovo account). Cliccate [ACCEPT AND DOWNLOAD] (Accetta e Scarica) e seguite le istruzioni per salvare l’installer del driver. Quando l’installer è stato scaricato, per installarlo sul vostro computer fate doppio click su di esso e seguite le istruzioni. Poi, scaricate e installate Line 6 Updater per lo Spider V Andate su Line6.com e cliccate su [Support]. Scegliete “Downloads” e selezionate nei tre menu a discesa di “Free Software Downloads” “Spider V 30”, “Line 6 Updater” e “sistema operativo Mac o PC”. Cliccate [GO]. La pagina si aggiornerà con l’Updater Line 6 per lo Spider V. Cliccate [GET DOWNLOAD] per scaricare sul vostro computer il programma di aggiornamento (Updater). Cliccate [ACCEPT AND DOWNLOAD] (Accetta e Scarica) e seguite le istruzioni per salvare l’installer dell’Updater. Quando il programma è stato scaricato, per installarlo sul vostro computer fate doppio click su di esso e seguite le istruzioni. Infine, aggiornate l’ampli Spider V Collegate la porta USB dello Spider V al computer con un normale cavo USB. Spostate il selettore SELECT sulla porta USB contrassegnata con Mac/PC. Accendete l’ampli. Aprite l’applicazione Line 6 Updater e registratevi con il vostro Account Line 6. Cliccate sull’ampli Spider V. Cliccate il pulsante [Update] in alto vicino all’ultima versione del firmware. Per iniziare l’aggiornamento seguite le istruzioni. Durante l’aggiornamento non spegnete né scollegate lo Spider V o il computer. Verificate sull’LCD dello Spider V che l’aggiornamento sia completato. Al termine, l’ampli si riavvierà. Scollegate e ricollegare il cavo USB, poi ripetete il procedimento per il Trasmettitore G10T. Nota: Se l’aggiornamento non va a buon fine o l’ampli si blocca all’accensione, tenete premuti i pulsanti AMP e FX per entrare in modalità Update. Una volta in modalità Update, eseguite di nuovo la procedura di aggiornamento. II. Aggiornare il firmware del G10T con l’Ampli Spider V Assicuratevi che l’ampli Spider V sia ancora collegato al computer e che il computer sia collegato ad internet. Inserite completamente il G10T nel jack di ingresso dello Spider. Assicuratevi che il selettore SELECT sia ancora posizionato sulla porta USB contrassegnata “Mac/PC”. Accendete il vostro Ampli Spider, se è spento. Lanciate il programma Line 6 Updater. Eseguite il login al vostro Account Line 6. Cliccate su [Relay G10T]. Cliccate il pulsante [Update] vicino all’ultima versione del firmware. Per iniziare l’aggiornamento seguite le istruzioni. Importante: Durante l’aggiornamento non spegnete né scollegate lo Spider V o il computer. L’Updater indicherà che l’ampli si sta resettando, ma voi guardate lo schermo dell’ampli, che continuerà l’aggiornamento, finché al termine scriverà “Part 1 of 1 100% Updating Transmttr”. L’ampli si resetterà, terminando il procedimento di aggiornamento.
-
Desplázate hacia abajo para ver las instrucciones en español. Faites défiler la page vers le bas pour trouver des instructions en français. Anweisungen auf Deutsch finden Sie weiter unten. Per le istruzioni in Italiano scorrete verso il basso. Updating Relay G10/G10S firmware from an internet-connected Mac or PC Video Tutorial: G10/G10S firmware update instructions for Windows users Video Tutorial: G10/G10S firmware update instructions for Mac users First, download the latest version of the Line 6 Updater for Relay G10/G10S: Go to www.Line6.com and click on "Support" Scroll down and select "Downloads" On the following page, set the three pulldown windows under "Free Software Downloads" to: [Relay G10 or Relay G10S], [Line 6 Updater], [your Mac or PC OS] Click "GO" The page will update with the latest Line 6 Updater version available. Click 'GET DOWNLOAD' to download the Updater program to your computer You will be prompted to either log in to your Line 6 User account or to create a new account Click on 'ACCEPT AND DOWNLOAD' and follow the on-screen instructions to save the Line 6 Updater installer file After the file has been completely downloaded, double-click on the downloaded file and follow the instructions to install it to your computer Mac Users: If you run into trouble with your Mac allowing you to install the download, please see this article. Next, update your Relay G10/G10S Receiver and Transmitter Insert the Transmitter all the way into the Receiver Connect the receiver’s USB port to your computer with the USB cable that was included in the box, or use a similar Micro-USB cable (Note: some Micro-USB cables only charge devices and do not pass data. Try multiple cables of you cannot get a connection) Run the Line 6 Updater program. Sign in to your Line 6 User Account. Click on “Relay G10/G10S Receiver” Click the “Update” button next to the latest firmware version. Follow the prompts to begin the update process. Important: Do not turn off or unplug your Relay receiver or computer during the update. After the update is complete, repeat the process for the Transmitter by disconnecting and reconnecting the USB cable, then clicking “Continue” in the Updater Please see this article if your computer does not detect your G10. Cómo actualizar el firmware del Relay G10/G10S Actualizar el firmware del Relay G10/G10S desde un Mac o PC conectado a Internet Tutorial en vídeo: Instrucciones de actualización del firmware del G10/G10S para usuarios de Windows Tutorial en vídeo: Instrucciones de actualización del firmware del G10/G10S para usuarios de Mac En primer lugar, descarga la última versión del actualizador de Line 6 para Relay G10/G10S: Visita www.Line6.com y haz clic en [Soporte]. Desplázate hacia abajo y selecciona “Downloads”. En la siguiente página, verás tres ventanas desplegables en “Free Software Downloads”; selecciona “Relay G10 o Relay G10S”, “Line 6 Updater”, “el sistema operativo de tu Mac o PC”. Haz clic en [GO]. La página se actualizará con la última versión de Line 6 Updater disponible. Haz clic en [GET DOWNLOAD] para descargar el programa del actualizador en tu ordenador. Se te pedirá que inicies sesión en tu cuenta de usuario de Line 6 o bien que crees una nueva cuenta. Haz clic en [ACCEPT AND DOWNLOAD] y sigue las instrucciones que aparecen en pantalla para guardar el archivo del instalador de Line 6 Updater. Una vez el archivo se haya descargado por completo, haz doble clic en el archivo descargado y sigue las instrucciones para instalarlo en tu ordenador. Usuarios de Mac: Si tienes problemas con tu Mac para instalar la descarga, por favor vea este artículo. A continuación, actualiza tu receptor y transmisor Relay G10/G10S Inserta totalmente el transmisor en el receptor Conecta el puerto USB del receptor a tu ordenador con el cable USB incluido en la caja o bien utiliza un cable Micro-USB similar (Nota: algunos cables Micro-USB solo permiten cargar dispositivos y no transmiten datos. Prueba con varios cables si no consigues conectarte) Ejecuta el programa Line 6 Updater. Inicia sesión en tu cuenta de usuario de Line 6. Haz clic en [Relay G10/G10S Receiver]. Haz clic en el botón [Update] situado junto a la última versión del firmware. Sigue las instrucciones para empezar el proceso de actualización. Importante: No desactives ni desconectes tu receptor Relay ni el ordenador durante la actualización. Una vez completada la actualización, repite el proceso para el transmisor desconectando y volviendo a conectar el cable USB; a continuación, haz clic en [Continue] en el Updater. Consulte este artículo si su computadora no detecta su G10. Mise à jour du système du Relay G10/G10S Mise à jour du système du Relay G10/G10S avec un Mac ou PC connecté à internet Tutoriel vidéo: Instructions pour la mise à jour du système du G10/G10S pour utilisateurs Windows Tutoriel vidéo: Instructions pour la mise à jour du système du G10/G10S pour utilisateurs Mac Téléchargez la version la plus récente de l’application Line 6 Updater pour Relay G10/G10S: Rendez-vous sur www.Line6.com et cliquez sur [Assistance]. Faites défiler la page vers le bas et sélectionnez «Downloads». A la page suivante, réglez les trois menus déroulants sous «Free Software Downloads» sur «Relay G10» ou «Relay G10S», «Line 6 Updater», «votre système Mac ou PC». Cliquez sur [GO]. La page affiche la version la plus récente de Line 6 Updater. Cliquez sur [GET DOWNLOAD] pour télécharger l’application de mise à jour sur votre ordinateur. Vous êtes invité(e) à vous connecter à votre compte utilisateur Line 6 gratuit ou à créer un compte. Cliquez sur [ACCEPT AND DOWNLOAD] et suivez les instructions pour sauvegarder le fichier installeur de l’appli Line 6 Updater. Une fois le fichier téléchargé, double-cliquez dessus et suivez les instructions pour l’installer sur votre ordinateur. Utilisateurs Mac: Si votre Mac ne vous autorise pas à installer l’appli téléchargée, lisez cet article. Mise à jour de votre récepteur et émetteur Relay G10/G10S Insérez l’émetteur à fond dans le récepteur. Reliez la prise USB du récepteur à l’ordinateur avec le câble USB fourni ou un câble micro-USB similaire. (Remarque: Certains câbles micro-USB se bornent à charger les dispositifs et ne transmettent pas de données. Essayez différents câbles si vous n’avez pas de connexion.) Lancez l’application Line 6 Updater. Identifiez-vous avec votre compte utilisateur Line 6. Cliquez sur [Relay G10/G10S Receiver]. Cliquez sur le bouton [Update] à côté de la version la plus récente du système. Suivez les instructions pour lancer la mise à jour. Important: N’éteignez pas et ne débranchez pas le récepteur Relay ou l’ordinateur durant la mise à jour. Après la mise à jour, recommencez la procédure pour l’émetteur en débranchant et rebranchant le câble USB, puis cliquez sur [Continue] dans l’Updater. Veuillez consulter cet article si votre ordinateur ne détecte pas votre G10. Aktualisieren der Relay G10/G10S-Firmware Aktualisieren der Relay G10/G10S-Firmware mit einem Mac bzw. PC mit Internetzugang Video-Tutorial: Anweisungen zum Aktualisieren der G10/G10S-Firmware (Windows) Video-Tutorial: Anweisungen zum Aktualisieren der G10/G10S-Firmware (Mac) Laden Sie sich die aktuelle “Line 6 Updater”-Version für den Relay G10/G10S herunter: Surfen Sie zu www.Line6.com und klicken Sie auf [Support]. Scrollen Sie nach unten und wählen Sie “Downloads”. Wählen Sie auf der nächsten Seite mit den drei Listenfenstern unter “Free Software Downloads” zunächst “Relay G10” oder “Relay G10S”, dann “Line 6 Updater” und Ihr Computer-Betriebssystem. Klicken Sie auf [GO]. Auf der jetzt erscheinenden Seite wird die aktuelle “Line 6 Updater”-Version ganz oben angezeigt. Klicken Sie auf [GET DOWNLOAD], um sich das Updater-Programm herunterzuladen. Loggen Sie sich in Ihr Line 6-Benutzerkonto ein (oder legen Sie sich ein Konto an). Klicken Sie auf [ACCEPT AND DOWNLOAD] und befolgen Sie die Hinweise zum Sichern des “Line 6 Updater”-Installationsprogramms. Nachdem die Datei komplett heruntergeladen wurde, doppelklicken Sie darauf und befolgen die Hinweise für die Installation auf Ihrem Computer. Mac-Anwender: Wenn Sie die heruntergeladene Datei nicht auf Ihrem Mac installieren dürfen, siehe diesen Beitrag. Aktualisieren des Relay G10/G10S-Empfängers und -Senders Schieben Sie den Sender komplett in den Empfänger. Verbinden Sie den USB-Port des Empfängers über das beiliegende (oder ein separat gekauftes) Micro-USB-Kabel mit dem Computer. (Anmerkung: Bestimmte Micro-USB-Kabel dienen nur zum Laden und übertragen keine Daten. Probieren Sie bei Bedarf mehrere Kabel aus.) Starten Sie “Line 6 Updater”. Loggen Sie sich in Ihr Line 6-Benutzerkonto ein. Klicken Sie auf [Relay G10/G10S Receiver]. Klicken Sie auf den [Update]-Button neben der aktuellen Firmware-Version. Befolgen Sie die Anweisungen, um die Aktualisierung zu starten. Wichtig: Schalten Sie den Relay-Empfänger bzw. Computer bei laufender Aktualisierung nicht aus und lösen Sie nie die Verbindung. Nach geglückter Aktualisierung muss der Vorgang für den Sender wiederholt werden. Lösen Sie die USB-Verbindung kurz und klicken Sie im “Updater” auf [Continue]. Bitte lesen Sie diesen Artikel, wenn Ihr Computer Ihr G10 nicht erkennt. Come aggiornare il firmware del Relay G10/G10S Aggiornare il firmware del Relay G10/G10S da un Mac o PC collegato ad internet Tutorial Video: Istruzioni per l’aggiornamento del firmware di G10/G10S per utenti Windows Tutorial Video: Istruzioni per l’aggiornamento del firmware di G10/G10S per utenti Mac Innanzitutto scaricate l’ultima versione dell’Updater Line 6 per Relay G10/G10S. Andate su www.Line6.com e cliccate su [Support]. Scorrete in basso e selezionate “Downloads”. Nella pagina seguente, in “Free Software Downloads” selezionate nei tre menu a discesa “Relay G10 o Relay G10S”, “Line 6 Updater” e “sistema operativo Mac o PC”. Cliccate [GO]. La pagina si aggiornerà con l’ultima versione disponibile di Line 6 Updater. Cliccate [GET DOWNLOAD] per scaricare sul vostro computer il programma di aggiornamento (Updater). Vi verrà chiesto di loggarvi con il vostro account Line 6 o di create un nuovo account. Cliccate [ACCEPT AND DOWNLOAD] (Accetta e Scarica) e seguite le istruzioni sullo schermo per salvare il file dell’installer di Line 6 Updater. Quando l’installer è stato completamente scaricato, per installarlo sul vostro computer fate doppio click sul file scaricato e seguite le istruzioni. Utenti Mac: Se avete dei problemi perché il vostro Mac non vi permette di istallare, leggete questo articolo. Poi, aggiornate il vostro Ricevitore e il Trasmettitore Relay G10/G10S. Inserite completamente il Trasmettitore nel Ricevitore. Collegate al vostro computer la porta USB del ricevitore con il cavo USB contenuto nella confezione o usate un cavo Micro-USB simile (Nota: alcuni cavi Micro-USB possono solo ricaricare i dispositivi e non passano i dati. Se non riuscite ad ottenere un collegamento provate più cavi) Lanciate il programma Line 6 Updater. Eseguite il login al vostro Account Line 6. Cliccate su [Relay G10/G10S Receiver]. Cliccate il pulsante [Update] vicino all’ultima versione del firmware. Per iniziare l’aggiornamento seguite le istruzioni. Importante: Durante l’aggiornamento non spegnete né scollegate il ricevitore Relay o il computer. Terminato l’aggiornamento, ripetete il procedimento per il Trasmettitore scollegando e ricollegando il cavo USB, poi nell’Updater cliccate [Continue]. Consulta questo articolo se il tuo computer non rileva il tuo G10.
-
without the transmitter the base has a slow while pulse. Insert the transmitter into the base and the base does a quick red pulse. The transmitter does noting. No lights at all. No matter how long I keep the transmitter plugged into the base it doesn't seem to help. There is noting transmitted when plugged into any guitar. I've used many different adapters and also left the transmitter plugged into a guitar to try and deplete all charge to start a new fresh charge. Noting seems to make the transmitter light up green, red white etc. Also when I try and update the firmware the updater shows there are no updates even though I'm at V1.0. I've downloaded V1.3 and V1.4 and the installer will not update my G10. Anyone else have this happen?
-
I am a gigging musician and the G10 remote system is an answer to a maidens prayer - however, the point of failure is the power cord for the base unit which is a really nasty little micro usb plug which is so loose that it becomes a lottery as to whether the unit is going to work or not - surely there should be a much more robust plug than this - anyone out there with similar views? Come on Line 6 - you are better than this!!
-
I have a Relay G10 which I bought it in October 2018. It's been either in my guitar being used, or in the charging cradle, plugged in, in that period of time. Very recently, it's dropped from more than an hour (don't know exactly, but I normally play for max an hour at a time), to about 7 minutes before it flashes Red and dies. I'll check but I don't think there's even a brief flash of Orange before it dies. I have the box and receipts, I don't think I registered it at the time of purchase. Does anyone know if this is a common situation, or if I have any comeback? I've done a firmware update om transmitter and receiver and it didn't help. Thanks friends.
-
I am using the G10 system. Is it possible to have 1 x transmitter in use in my guitar whilst I have another transmitter on chage at the same time in the base unit?
-
The transmitter of my G10 seems to have spontaneously failed. No sign of life at all. The halo on the charger flashes red, but the jack-plug device shows no light, nothing. The unit's about two years old and has performed perfectly up to now. I raised a support ticket online with Line6 and they asked me to download the firmware update and apply it. I did. Not surprisingly it told me it couldn't see the transmitter. The support desk also said that if the firmware update failed, I should contact my local (UK) service company, who are in Milton Keynes. Once I'd got past the autoreply bots, a real person said that they could have a go at fixing it if it's still under warranty (which I'll have to check) or, as the transmitter is relatively cheap, just buy a new one - the transmitter only. All of which raises a few questions. 1) Has anyone else had this sudden-death issue? 2) Can I indeed buy just the jack-plug transmitter bit? 3) If I do, how will the charger/receiver pair with it? I asked the guy that last question, and he said "it'll just work. Any receiver will work with any transmitter". Which raises the question of what would happen if I had two of them, and only one of them needed a new transmitter. Does the transmitter speak to the receiver it most recently was plugged into, or something? Anyway - I feel a bit passed around. Neither Line 6 nor the servicing partner seem that keen on getting involved, so I thought I'd ask for advice here. Thank you for your time, M
-
I successfully installed and ran the Line 6 updater but it could not find a more updated firmware version form my Relay G10 than version 1.00 though I know new versions exist from reading the forums. I noticed that the updater will allow me to specify a file location. Where can I download version 1.04 (or later) for installation?
-
I have a 19 guitar collection. I have had 3 issues. Solved #1....Ibanez S relay would not fit......my solution, a minor sanding of opening with a Dremel tool and filled the color with a matching magic marker in blue. You don't notice the mod. #2- Michael Kelly hydride will play through he hum buckers, but the piezo acoustic pick up has no sound. Any ideas as to why? #3- Ovation Koa topped acoustic. While it is not an expensive model it sounds awesome plugged in, but when I try the G10 I get sound for about 10 seconds, a loud pop, and then a awful squeal that will not quit. I love that guitar, but it's strange what happens.The model # is gone (sticker lost a while back) but it is not a high end model, but it sure sounds like one. The electronics are the standard Ovation brand. I would like to get the 2 guitars to work......any suggestions?
-
Hey guys, I recently bought a G10 wireless. Now, i've used it live, worked perfectly and was actually very happy with it. But I got home and the damn thing will not work. The receiver is just flashing red (on the halo) about 1 flash a second, when I plug the transmitter in. The transmitter does not turn on, at all, I charged it for 4 hours, then tried it, nothing. I tried it overnight, then nothing... I'm at a loss i really am. Guitars tried: Ibanes RG8 Dingwall NG2 (this was what it worked with live) Fret King Corona Ibanez SR505 Ibanez S420 Legator Ghost 7 string with EMG 707s Any advice would be greatly welcomed right now! Thanks!
-
I can not speak English because I am a foreigner. I wrote using Google Translator. Good morning. I am using FIVE O pickup now. The instrument uses an ukulele. The pickup uses a 3v CR2032 battery. When this pickup is connected, white noise is generated. There are two instruments equipped with this pickup, but they all have the same symptoms. Other passive pickups did not have this symptom. There was also no noise in the fishman pickup installed on the guitar. The Fishman pickup used a 9v battery. I want to remove this noise. ↓ five-O pick up Noise T^T
-
I'll start with a simple question, which someone may be able to answer off the top of his/her head. Then, I'll go into a tedious explanation of what I'd like to accomplish. First, the question: If my JTV-59 is connected to a compatible Line 6 device with a VDI cable, will the analog output at the guitar's 1/4" output jack be suppressed, or could it be connected via a standard guitar cord to play through an amplifier? Now for the rest of the story, which may spark an alternate solution, or may result in a 'You can't get there from here' unhappy ending... The battery on my JTV-59 doesn't seem to have much longevity, despite the fact that I use the mag pickups more than the modeling. I'd like to be able to power it for everyday use and practice by connecting it to my Pod XT Live via VDI. But I'd prefer to go wireless into my Amplifi 30 through a Relay G10 plugged into the 1/4" output, because I like the sound of the Amplifi more than the output of the Pod XT played through my stereo amplifier. In this scenario, I'd essentially be using the Pod XT Live as an expensive power supply. But that's ok -- it's paid-for... If the output continues to be available at the 1/4" jack while connected via VDI, it would also open up the possibility to use the Pod XT Live to change models on the JTV, which would be VERY cool. I'd still be using the Amplifi for amplification, but wouldn't have to play with the knobs and switches on the guitar in the middle of a song. Another option that solely addresses the power issue may involve the XPS footswitch, which I've basically never used, although I have at least two of them, supplied with my Variax 500 and 600 guitars. Maybe it would be possible to power the Variax with the XPS and it's 3-conductor guitar cable, and plug the Relay G10 into the 1/4" output of the XPS box? I know: I could try these combinations, myself. And probably will. But I thought it would be useful to throw these scenarios out there and see if others have tried or given thought to possibilities such as these. Look forward to hearing any ideas or suggestions...
-
I just purchased the G10. First gig. No issues. Day 2 2nd set...Had reciever seated. Full green light. Played for 2 songs and all of a sudden drop outs every few minutes. Had to plug in after the song for the rest of the gig. Hoping it was a freak thing but after reading all the people with drop out issues, I may need to send this back. I will give it another shot for the 2 gigs coming up this weekend. Any recommendations?
-
Hi everyone. I'm getting a G10 to use from my guitar to the Helix and was wondering if I could add yet another G10 to the chain. Out the Helix to the G10 and from that going wireless to the mixer. My goal is to have zero cable here and there and avoid the hassle of connecting and checking conections every rehearsal/gig. Do you guys think this: Helix > G10 > Mixer would work? I mean, with a decent audio quality? Anyone already doing this that can share experience/s? Thanks
-
Forgive me if this has been addressed elsewhere (I looked but couldn't find the answer). I'm currently using the Relay G10T with my Spider V 120. It works great. It doesn't have a receiver because, apparently, it's already built into the 120. But I'd like to purchase some wireless headphones and was wondering if anyone has any tips on how to reduce interference or latency (if they've even had any problems), or if they use a particular pair of headphones and/or transmitter that work well for them. Any suggestions? Has anyone had any problems using wireless or bluetooth headphones simultaneously with the relay on their Spider V?
- 1 reply
-
- headphones
- g10
-
(and 1 more)
Tagged with:
-
Hi all, I recently bought a G10 system and have so far used it for a couple of gigs and a few rehearsals and it has been flawless, but reading the various forums I am concerned about the USB connection lasting. I play in a band which practices once a week and gigs 2 -3 times a month. I only really wanted a wireless system to free the stage of cables, I'm not planning on running into the audience, so the G10 looked ideal. Most of the posts I've seen about the dodgy USB connection seem to be from last year, so I was wondering whether this has been improved? I've been looking at alternatives but the G30 seems to have issues with the battery door and clip and the G50 or G70 seem overkill for what I need. My local music store has the G70 at a really good price at the moment (cheaper than the G50), so I'm wondering whether to bite the bullet and exchange the G10 for this, even though I will never use most of the features, just so that I know that it will be road worthy. Any advice will be really appreciated.
-
We use a Behringer XR18 mixer and BandHelper, both of which use tablets/phones & wifi extensively. Some of these are 2.4HGz units. Can anyone tell me if a G10 is likely to wipe out my 2.4 tablet (or more than that) at about 3 feet away, with the router about 20 feet away and everything else in between? I realise that the G10 won't be joining the network but that could be worse because the router can't tell it to shut up. Also, the only thing ON a network which would be streaming data would normally be the router, not some 'rogue' other device in the room. Thanks
- 4 replies
-
- g10 2.4 wireless network
- g10
-
(and 3 more)
Tagged with:
-
Hi there, is there a known solution to plugging G10 transmiter to Ibanez soundgear bass guitars? Tried it with the included adapter but it is too short...
-
Love my G10...works wonderfully. My question is...I have it plugged into power 24/7. Does anyone know any reason why this might cause issues? Shorter battery life or overheating or ? No issues...and I use it several times a week during practice...and it goes to a solid green a few minutes after putting the transmitter back into base. So it appears to be working fine...just want it to last. Thanks Dave