Search the Community
Showing results for tags 'hx effects'.
-
While trying 4CM using my HXFX and a Boogie Rectoverb head (effects loop in amp modified to series ) I noticed a hum, ground loop style coming from my amp. I tried the same setup with a Marshall JCM 900 with the same result. When I insert a Ebtech hum eliminator on one of the lines the hum goes away. If the HXFX is connected to either amps' effects loop in the common way there is no hum. I tried with a variety of cables with same results. Anyone else have this problem?
- 2 replies
-
- hx effects
- 4cm
-
(and 1 more)
Tagged with:
-
Hey Guys, I've just picked up a Line 6 Hx effects! Love it!, I currently run a Boss MS3, but want to intergrate the HX into the pedalboard too, any idea's? I'm using the Boss MS3 as my main controller, but open to new options and i really like the drives on the HX,... I'm thinking.... Wah- MS3-HX effects-Boss Space Echo-OUT.... Any advice or ideas would be super helpful.
-
I recently purchased a FX effect unit and really like everything it can do. I'm running 4cm into a Hughes and Kettner tubemeister 36 head. As I'm building a scene, i get the distortion from the HX effect dialed in. As I add to the signal chain and place the effects loop (after the distortion) the sound becomes thin, almost like a am radio. If I turn the loop off i get the original sound. Am I missing something on the set up? I have a comp, Distortion, fx loop, chorus, delay, and noise gate. Other than using snapshots to turn the loop on only when I want the amps distortion, am i missing something in the set up?
-
So my rig is: Guitar -> HX Effects -> Fender Hot Rod Deluxe. Im putting everything into the front of the amp. The issue I'm facing is when I play really hard and get loud notes there's a deafening pop that comes from the amp. It doesn't make much difference which drive I'm using but just sends this digital popping sound which makes it unusable live. I've tried playing with guitars - ESP with Seymor Dunc JB are the worst. My Fender Strat is not as bad but bad enough. I don't think my amp is the issue.. when plugging in my old prdals (OCD, Flashback, etx) its fine. I've showered all forums but can't seem to find this issue reported before. Anyone got any ideas?
-
I have an on going issue that I can't seem to figure out that I've been trying to figure out for months. When running my Strymon BigSky and Timeline either in a loop or if I try to run in stereo by using the left and right outputs on the HX Effects I get digital clipping. When running them in the loop I've had to adjust the Send volume down by around -16db to eliminate the clipping, then I max the Boost on the BigSky (+3db) and then max in Return volume on the HX Effect out just to try and get close to the original volume (I think the max is +6db if I remember correctly). Then when I try to tun the Strymon pedals in stereo by using both outs on the HX Effects since there is no volume adjustments for the outs I found that if I use the low pass filer on the BigSky that helps clean up the issue. All this brings up several questions. Is this normal? Am I doing something wrong? Is there maybe something wrong with my HX Effects? What I really want to do is run a true stereo set up where I run out to the front of 2 clean amps but I don't want to loose signal volume or integrity, which might make using a loop an issue because I don't think you can use a single loop in stereo and I have my drives on the first loop so I can use a noise gate and compressor in front of them on the HX.
-
Hello! Anyone out there using HX Effects with Tech21 Trademark 60? I recently got the Hx fx. Wonderful gear. Full of great features. Used some pods before. Recently Pod Hd500x. But the Helix family seems to take it a step further. I got the HX Effects to try to make the most of it and its features. I use the loops, loop 1 to insert some pedals (mainly distortions) and loop 2 to make the 4 Cable Method (4CM). I have an expression pedal on input 1 and was trying to control my amp functions with the Ext Amp 2. So far I was able to change channel but I can't access any other functions on my amp. Can't control Boost/Reverb function neither Fx loop on/off. The only thing I can think about is that this happens because my Trademark amp usually uses a standard (mono, Tip/sleeve) cable to connect to its original footswitch and I think the Hx Fx is supposed to use a TRS jack cable. I've tried both with the same result. I can only switch between amp channels. While reading the manual trying to solve this I came across something that worried me because I really don't know what it means: "IMPORTANT! Connect EXT AMP 1/2 only to amplifiers that utilize "shortto-sleeve" footswitch inputs. Connecting to any other sort of input could cause permanent damage to both your amp and the HX Effects device! If you're not sure if your amp has short-to-sleeve inputs, contact the manufacturer." I don't know what "short-to-sleeve" means... and if this amp applies or not. Could this be the problem? Am I in risk of damaging my gear? Anyone can think of something that might help me? Thank you so much! Keep rocking and rolling!
-
- hx effects
- tech 21
-
(and 2 more)
Tagged with:
-
I'm trying to get that "Friday Night Lights (Daniel Lanois - Sonho Dourado) sound". Any suggestions on a pedal effects train to get the job done? (there are some youtubes that look like they might have info, but are in Spanish, lol). I'm looking for an ideal case layout suggestion to see what I can close to with my existing rig. (I've got Boss Comp/Sus (CS-3) & EQ (GE-7) pedals running into a Line 6 HX Effects unit. I usually play small gigs directly thru my Boss L1. Main Axe is a Godin Multitac Spectrum SA with D'Addario flat wound Jazz strings). Thanks!
-
Hey guys i want to send a few drive pedals through the fx loop on my hx effects. most of them work ok. trying to connects the zvex box of rock. and it make a lost of noise when connected and engaged. is there a solution for this? it also happens with fuzz pedals when i do it, but that was kind of expected. thanks danny
-
hello, with a simple delay, i wonder why when i changed tempo by tap tempo switch, the red light is following the tapped tempo, but i get no changed tempo on sound. delay stayed with the same time as before. can you help me?
-
Hi all. I currently use a Joyo looper to control my non midi pedal set up. The unit has a midi out and I'm looking for any basic guidance / tips on how I cold integrate a HX unit into the rig. Any help would be greatly appreciated!
-
- hx effects
- midi
-
(and 1 more)
Tagged with:
-
So, I haven't tried this yet, but I plan to and if it works it will be pretty cool... (if it doesn't, I guess I'll have to start it as a suggestion on the Idea thing). JHS makes a pedal that they call the stutter (or something like that) and it is a momentary killswitch. Basically, you can tap the switch on this pedal and it kills the signal until you let go, so you can tap a patter and it will "stutter" to that pattern. I was thinking that I might be able to set up a footswitch on the HX effects to do the same effect (have it control the position value of the volume pedal effect with the level 100 normally and have it go to 0 when depressed). What ya think?
-
I looked around the board and didn't see this mentioned so I'll ask it here. Can you set up a single effect to be used for the entire HX effects unit, that does not take one of the foot switches to activate? I always use a compressor and there is one in the HX Effects units that I like, and I would like that to be on all the time, regardless of the bank and/or patch that I am using. Right now I have to use one of the six buttons for the compressor on every patch, which kind of wastes a button. If I could assign a global effect, that is always on for every bank, that would be awesome since it would leave room for 6 other effects. Appreciate any help.
-
I think it would be cool if there were a global setting that allowed for six snapshots. With this setting enabled, the mode button would be used as a three way toggle between preset, pedal board, and snapshot modes. Update 2.80?
- 1 reply
-
- hx effects
- snapshots
-
(and 4 more)
Tagged with:
-
Hello all! I was using my new HX Effects and getting deeper into my banks, I realized even though I have 2 expression pedals hooked up I was not able to add 2 different volume pedals as 2 different blocks. I like setting up stereo, splitting the the A/B into separate distortions and delays, figured each line needed a volume pedal! I realize I was trying this from the software and not the actual unit itself to adjust the blocks, there is a bit of time yet until the software does everything I was reading. I will try from the unit itself tomorrow when back at it in the AM. Has anyone else noticed this by any chance? Just curious in the meantime before I get to mess with it more myself. I'd love to request this in a future programming update.
- 2 replies
-
- hx effects
- volume pedal
-
(and 2 more)
Tagged with:
-
hi. I would love to add to the request for a future update the ability to have 6 snapshots. you could use the mode button to toggle between presets / snapshots / stomp mode/
-
Cant connect my hx effects on hx edit, it says code 8207 I just recently purshased this device and I cant use from my pc.
- 3 replies
-
- hx
- hx effects
-
(and 1 more)
Tagged with:
-
Hey friends, I'm looking to get a Garcia-style envelope sound. What's your experience with dialing that in with either an HX Effects or Helix?
- 1 reply
-
- hx effects
- helix
-
(and 1 more)
Tagged with:
-
A bit of background info- Running HX effects straight into the front of an egnater renegade 212 combo. I have set up channel switching (clean/dirty) in the HX using a trs cable from EXT 2 and am trying to set up an expression pedal (Dunlop Volume X mini) on EXT 1. the Dunlop volume X mini works perfectly on EXT 2 for volume blocks but I can’t only get a small sweep (approximately 65%-90%) on EXT 1! I used a TS cable in both setups. Amp channel switching works perfectly on EXT 2 as well, but will not work on EXT 1 jack (yes I changed the setting from tip2 to tip1). In my perfect setup EXT 1 would be my Dunlop Volume X mini - used for volume swells, wah or any other parameter change I need depending on my preset. And EXT 2 would be dedicated to amp channel switching. am I having issues with the Dunlop in EXP 1 jack because it’s default to wah? why wouldn’t both EXP jacks behave the same and be able to do whatever I program them to?! any help would be appreciated!
-
- hx effects
- expression pedals
-
(and 1 more)
Tagged with:
-
I see users offering custom made tones to download for the HX Effects unit. How do I upload them to my HX Effects device?
-
Opened support ticket. Anyone having bug when you must press twice on patch to activate all blocks? . Not every time but it's very often. I'm on 2.60 version. First response from Line 6 is that there is bug with HX Editor 2.60, but for me problem occurred even after FULL reset and after I made my new patches using HX FX hardware. I just used Hx Edit to export those patches. Maybe the bug from HX Edit "contaminated" my clean hardware again. Support ticket is open, so will post the updates.
-
Hi, is it possible to hook up an external tap tempo switch to the HX effects? And if yes what do I have to set in what menu?
-
Hi, I tried so hard to connect my HX effects as a sound card on my MAC. My mac recognized my HX effects as a MIDI but not as a sound card. There's no available drivers / Monkey 6 for HX effects (mac) on download section of the website. How can I resolve that ? Thanks for your help Jonovan
- 10 replies
-
- hx effects
- mac
-
(and 1 more)
Tagged with:
-
can I add to the request list a second page of footswitches. maybe if you hold down footswitches 3 and 7 simultaneously it takes you to a second page of footswitches. would be very useful.
-
hey there. can I add to the list of requests - the ability to assign the tap button to something. IE the fast slow on the rotary. or things like that
-
HI folks, I'm new to the board, so thank you for any help in advance! I'm using an HX effects in 4CM to channel switch my 5150 via TRS cable through EXP PEDAL 1. Long story short - it works for while, then it seems to send odd signals to the 5150, and when i switch snapshots (effectively) from red to green channel i get volume drops. If i turn the HX on and off, it seems to reset and all is well; but i only get a few switches and it goes again. It's really adhoc. I've reset, updated, tried different cables, works sometimes for hours, then goes mental again. Can't "make" it do it either. If i integrate the official 5150 switcher it's functioning fine, but i'd like to utilise the switcher option obviously. Thanks folks! andy