Search the Community
Showing results for tags 'panning'.
Found 4 results
Hello. I was wondering if any of you have experienced any issues with the headphone output of the Helix LT or Helix Floor? I have an Helix LT connected as an audio interface to my Windows 10 laptop. I only use headphones and like to jam along with YouTube and guitar pro and recently when I listen to a preset through my headphones connected to the output jack of my Helix LT, the panning/volume is all wonky and is not balanced with the right side noticeably louder than the left. The issue is across all my patches including factory and user). The issue seems to be volume related, if you crank up the amp or add a distortion block it seems to pan harder to the right and becomes very off putting. If you turn the volume knob below 12 o’clock the panning balances better, turn the volume knob up to 3 o’clock or to full then panning is almost hard right and I can hardly hear anything from the left as if you’ve have duff headphones. As a temporary work around I have to pan the output block at the end the chain by at least 30% to the left to balance the sound. I've tried different 1/4 inch adapters and different headphones, I have some in ear monitors and a pair of Beyerdynamic DT770 pro 250 ohm and the issue persists. I have even sought a second opinion from my wife who agrees there is Definitely a panning/volume issue. There is no problems when listening to music and videos from YouTube etc. It only affects my guitar patches. Also, this seemingly started happening out of nowhere. I do not recall making any changes to global settings, but perhaps that is where the problem is? I am updated to firmware version 2.92 and have been since it was released. Out of desperation I have completed a factory reset and even rolled back the firmware to 2.8 and reinstalled 2.92 with no joy and I am now worried it may be a hardware issue. Everything has been working fine until now. If anybody could help me figure this out, I would really appreciate it! Thank you.
I am new to helix, I have a guitar with the ability to spilt my pickups. I have sucessfully routed my front pickup to return 1 and my bridge pickup to return 2.by programing the inputs accordingly I have built sounds that mix things like chiming delays on the front with distorted flanged sounds off the bridge. (thing I used to dream of). Is it possible to use the expression pedal (I tried without sucess using the pan block) to control how much of one channel is mixed with the other. I have been able to use the volume pedal to control one channel but I would like to mix .increase one and decrease the other while maintaing the same volume live. I am going out of the helix mono. I am a newbee to helix and any suggestions are welcome.
I've asked in the Facebook group and read some threads over here about the topic but some things about it still confuses me, so here we go again. Is there any panning law by default in the Helix while using Y splits or AB splits followed by a merge block? At what dB? Is the signal lowered att the split or at the merge block? I'm using a patch for my bass that has a y split in the beginning with some distortion blocks on path 1b, and no blocks on path 1a, followed by a merge block, some comp, mod and lastly a single amp block and a cab. I use this setup to "blend" the distortions with my clean bass tone before hiting the amp block. But something sounds "off" while doing this compared to just putting all the blocks on a single path. I do understand how panning does work and that merging two mono signals results in a boost of 3db, two stereo signals in a 6 db boost, etc. Allthough i compensate by cutting the output block of the merge block I still end up by a signal that sounds either slightly boosted or with to little gain hitting the amp block. The settup that seem to be working the best is to use a Y split with L+R hard panned to either side and then both panned center at the merge block + a -3db compensation at the merge blocks output gain. Even by doing this you can clearly hear a difference when moving fxs like a comp block before or after the split+merge. Am I missing something? I do not have the dist blocks in path 1b on all the time and I want my blocks to get the same amount of signal after the split/merge as if I wasn't usinging parallel paths. Is this even possible?
I just noticed my audio interface mixer software had the all the analog & DAW inputs panned to center. For example, my analog inputs 1 & 2 would be paired for stereo but each channel is setup for center. I changed panning to hard left and right and now the audio is in true stereo.... The question I have for this forum is how do you guys set your Helix panning outputs when creating presets for recording or live performance? Do you use A path with center panning or prefer A + B path with some combination of left and right panning?