Search the Community

Q: What is the difference in power rating between tube and solid-state power amplifiers? A: Tube power outputs can peak 200 to 400% above solid-state, so a 50watt tube power amp can output a volume equivalent to a 100-200w solid-state amplifier output. Q: What are the common Preamp tubes? A: The 12AX7 (ECC83 is the European term, or the military term of 7025) is the most common preamp tube for driving the Gain and EQ sections of the amplifier, as well as driving the signal into the power amps. The following tubes have a lower power rating and can be used in the preamp section or other amplifier functions such as the reverb tank drivers, inverters, etc. 12AT7 (ECC81, 6201): 60% power of the 12AX7 12AU7 (ECC82, 5963): 19% power of the 12AX7 12AY7 (6072): 45% power of the 12AX7 Q: What are the common power amplifier tubes? 6L6 (5881/KT66): Commonly used in American amplifiers such as Fender, Mesa, Peavey. Typically has more low-end emphasis. EL34 (6CA7/KT77): Commonly used in British amplifiers such as Marshall. Typically has more midrange emphasis. EL84 (6BQ5): Commonly used in Vox , Gibson, Matchless, and Bad Cat amplifiers 6550 (KT88): Commonly used in VHT, Ampeg SVTs, and Leslie Speakers cabinets. Typically has more power output than the other tubes listed here. Q: What other power amp tubes are compatible with the Spider Valve? A: Line 6 stresses using 6L6 (5881/KT66) power amp tubes only. Other power amp tubes such as 6550's can draw too much power and damage your amp and void your warranty. Q: How long should I let tubes "cook" after biasing before I measure again? A: The standard cooking time is 3-6 hours after an initial bias (regardless of the tube age).

Q: What is the XPS Unit? A: The XPS unit is the power supply that powers the Variax instrument via 1/4" TRS cable. The Line 6 XPS box must be powered by a Line 6 PX-2 power supply for correct operation. There are three variations of the XPS: XPS-AB: This units acts as both a Variax power supply and has an A/B footswitch to send the guitar output to either a 1/4" or XLR output. Use a standard XLR (microphone) cable to connect the XPS-AB’s XLR output to feed any balanced input. Use a TRS (Tip-Ring-Sleeve/Stereo) cable to connect your Variax to the INPUT jack of the XPS-AB, a standard mono instrument cable to connect the 1/4" output of the XPS to any standard amp rig. XPS-Mini: This unit ships with the Variax 300 series, and has an 1/4" input and output. XPS-DI: This unit shipped with the Variax Bass Instruments and had an line/mic level switch, as well as an XLR ground lift option. The XPS-DI uses a standard XLR (microphone) cable to connect the XPS-DI output to feed any balanced input. Use a TRS (Tip-Ring-Sleeve/Stereo) cable to connect your Variax to the INPUT jack of the XPS-DI, and a standard mono instrument cable to connect the 1/4" output of the XPS-DI to any standard amp rig. Note: This unit is no longer available as the Variax bass has been discontinued. Usage F.A.Q.s Q: Can I use the XPS-AB as a replacement for my XPS-DI? A: Yes, the XPS-AB is the direct replacement for the XPS-DI. Q: Can I use the XPS-mini if I do not have access to the XPS-AB box? A: Yes, the XPS-Mini can be used in place of the XPS-AB box. Be aware that the XPS-mini is the only supported power supply for the Variax 300 series instrument, due to a slight increase in the power requirements for the 300 series. Q: Will the XPS-DI recharge batteries in Variax Instruments? A: No. Q: What type of cable do I need to use to connect the XPS unit to my Variax Instrument? A: You will need to use the supplied 1/4" TRS cable (or equivalent) to connect your XPS box to your Variax instrument to deliver power. Any mono 1/4" cable will work if you are using the internal batteries for power, but the power will be drawn from the batteries rather than from the cable. Q: Can I use the XLR and 1/4" outputs simultaneously? A: No the XLR and 1/4" outputs can only be used separately. Q: Does the Footswitch provide phantom power to another device? A: No, the A/B footswitch for your Variax will not provide phantom power. Q: Can I plug my regular electric instrument into the XPS box? A: Yes, if using a standard mono guitar cable, you can plug your regular electric instrument into the XPS box without damaging your guitar. We do not advise the use of a TRS cable with anything but a Variax because of the power it carries back to the guitar from the XPS box. Also, we do not recommend using an XPS box with active guitars. The combination of voltage potentially feeding back into the guitar, and how the guitar is wired, which can vary, can potentially damage the guitar and/or the XPS box. Q: What is the length of the Variax digital cable? A: The Variax digital cable is 25 feet long. Troubleshooting F.A.Q.s Q: There is no audio signal and I am only seeing a "red" power light on the XPS A/B (DI) when connected to the Variax guitar using a TRS cable? A: If the XPS-AB/DI has the proper power connected (and is connected to the Variax) and is showing a "red" power light, this means that the XPS is not recognizing the Variax and not sending power. If a different TRS 1/4" cable does not resolve the problem, try a different XPS box to see if there is a problem with the XPS box. If a different 1/4" cable and XPS box does not solve the problem, the Variax may have an internal failure that will need to be resolved by an authorized service center. Q: I am getting a "popping" sound when changing between the XLR and 1/4" outputs when connecting to a PA system? A: This situation can happen when the mixer has phantom power applied to the channel that the XPS input. One solution is to turn off the phantom power on that channel, another solution is to put another DI between the XPS and sound board. Some end users with switch to using the different (compatible) Line 6 device. Q: My XPS Box is damaged/lost. How can I get a replacement? A: The XPS box can be special ordered from your favorite Line 6 dealer: Line 6 Dealer Locator

The POD X3/X3 Live does not offer phantom power which is needed when using any condenser type microphones for recording. You can purchase phantom power boxes from several online music dealers. Some boxes start as low as $30.00. For more information on phantom power and how it works, please see the link below. http://en.wikipedia.org/wiki/Phantom_power If using phantom power with your microphone, do not connect your microphone to the X3's Mic input. The X3 is not equipped to handle external phantom power. If you do not own a condenser type microphone and your POD is still not putting out any levels there are a couple things you can check. 1)Press the Inputs button on your POD and make sure the input for your tone is set to "Mic". 2)Check the Trim knob near the XLR input on the back of your POD and make sure that is turned up. At this point if you are still not hearing any signal output then your POD have a hardware problem and will need to be repaired. You can locate a Service Center near you on our website and arrange a repair for your POD.

1. Plug the Variax into the PODxt Live Variax input 2. Press the OUTPUT MODE b\utton and scroll the SELECT knob until you see MIDI/VARIAX. Use the fourth soft black button under VARIAX to activate input 3. Press the EDIT button. Scroll the SELECT knob clockwise to the very last page. 4. Change Variax models by highlighting MODEL with a soft button under the main LCD screen and use the tweak knob to the right of the screen. 5. Parameters are saved per patch and settings are reinforced when the patch is loaded. NOTE about Alternate Tunings: Alternate tunings are part of your Variax customization in Workbench and called up within a PODxt Live patch with the customized guitar model. To select or customize tuning in Workbench: 1. Click PRESET (1) at the bottom left hand corner of the editor screen. 2. Select 'Alternate Tuning' preset, load, and close. 3. Click SEND (2) and apply setting to one of your custom guitars. In the illustration I used Custom Lester Model 2*1 4. Go back to the Workbench Main Page and SYNC your Variax with the changed settings 5. You can now exit Workbench. On the PODxt Live: Select the model you wish to load & save patch to desired location.

Application Q: What are the presets on my Spider Valve amplifier? A: The user presets and artist/song presets for the Spider Valve are listed as attachments at the bottom of this document (please be aware that they are identical to the Spider III with the exceptions notated in the document). The Spider Valve user presets are the 36 user-programmable presets. The artist/song presets location cannot be saved, but you can modify and/or store these setting in the 36 user-programmable presets. If you would like to return your unit to the original presets, please perform a factory reset. Q: I noticed that some of the Artist/Song Presets from the Spider III are not present on the Spider Valve? A: Yes, some of the Artist/Song Presets from the original Spider III release were not included in the Spider Valve release due to space restrictions (please compare the two lists for clarification). Q: Are the Spider Valve series amps Mono(phonic)? A: Yes, the Spider Valve series amplifiers have a monophonic output (as are most tube amplifiers). Q: How can I connect a POD unit to my Spider Valve series amplifier? Connecting to Amps and Computers, Output Settings, Floorboard Compatibilty, Fletcher Munson, Multiple Amps Q: Do the Master volume and presence control applied to the power amp section only? A: Yes, the master volume and presence control are true analog. Q: Where is the Master volume located in the chain? A: it is after the preamp, and before the power amp. Specifications Q: What speakers are used in the Spider Valve amplifiers? Spider Valve 112: Celestion Vintage 30, 8 ohm Spider Valve 212: (2) Celestion Vintage 30s, 16 ohm Spider Valve 412 cabinet: (4) Celestion Vintage 30s, 16 ohm Q: What tubes ship in the Spider Valve amplifiers? What is the power output? Spider Valve 112: (2) Sovtek 12AX7LPS preamp tubes, (2) Sovtek 5881/6L6WXT power amp tubes. 40 watts. Spider Valve 212: (2) Sovtek 12AX7LPS preamp tubes, (2) Sovtek 5881/6L6WXT power amp tubes. 40 watts. Spider Valve HD: (2) Sovtek 12AX7LPS preamp tubes, (4) Sovtek 5881/6L6WXT power amp tubes. 100 watts. Q: What are the function of the 12AX7 tubes? A: V1 is the booster to the output tubes, V2 is the phase inverter for the output tubes. When viewing the amplifier from the back, V1 is on the left side on the combo and the right side on the head. Q: Can the SV handle another 12A_7 style tube without damage to tubes or circuitry? A: Yes, but as these tubes act as a phase inverter and a boost to the power amp (rather than traditionally "cleaning up" the preamp section), you may not get the result you are looking for. Q: What Line 6 controllers work with the Spider Valve series amplifier? Controller compatibility chart Setup/Connection Q: Is there a bias switch to change the power tubes to EL-34s or other power tube types? A: No, the Spider Valve does not offer bias switchable options and was designed to only be used with 6L6 power amp output tubes. Q: Is the effect loop series or parallel? Is the effect loop mono or stereo? A: The effect loop is series mono. Q: Is there a headphone output on the Spider Valve series? A: There is no headphone output on the Spider Valve Series, but you can use the XLR output to go to a mixer, then use the headphone jack from the mixer. Q: Can I run my Spider Valve amplifier without a speaker load? A:No, you cannot run the Spider Valve series without a speaker load. Please see the following link for more information on cabinet connections: Cabinet Connection and Ohm F.A.Q. Q: Can the Spider Valve be run with a Variac? A: This is not recommended as the lower voltage can cause problems with the digital processing in the Preamp section of the Spider Valve. Q: Can I run a Palmer S.E., THD Hot Plate, Power Soak, etc. for speaker simulation or power attenuation? A: There are no known issues regarding the use of any direct recording simulators or power attenuators between the power amp output and the speaker cabinet, but if there is damage caused by improper connections or malfunctioning gear it will not covered under the Line 6 warranty. Q: Do the 112 and 212 combos support external speaker cabinets? If so, will the external cabs mute the internal speakers of the SV? A: Yes, the Spider Valve supports the use of additional cabinets. Please ensure that the ohm load is correct to avoid damaging your amplifier. Q: What is the bias voltage for the 6L6 tubes? A: 35 ma (or mv) Q: Does the XLR output still send signal when the amplifier is on standby? Is there an FX loop? MIDI ports? A: The XLR Direct Out (which is a POD-style output with speaker simulation) will function when the amplifier is in standby mode.The Spider Valve has a pre-amp out (effect send) and Power amp in (effect return) section. There are no MIDI ports on the Spider Valve series. Q: What do the FBV shortboard stomp, FX Loop/Function 1, and Function 2 do? A: The Stomp button activates the "boost" on both the original (Mark I) and Mark II shortboard. The FX Loop (Mk I)/Function 1 (Mk II) activates the Noise gate. The Function 2 (Mk II only) has no function on the Spider Valve. Q: Does the FBV controller (long board) work any differently that the other FBV controller switch the Spider Valve series? A: The FBV controller (long board) work just like the other controllers, but there are numerous buttons that will have no functions, such as the Stomp 2/3 buttons, tremolo, and favorite channel. Q: Where is the fuse located in the chain? A: The fuse is located between the 12AX7s and 6L6s (there is no "master" fuse). Spider Valve Cabinet FAQs Q: What are the specs for the 4x12 cabinet? A: 9 ply, ¾" wood with Celestion Vintage 30 speakers. There is no ‘internal baffle`. Q: What are the ohm load options for the 4x12 cabinet? A: The switchable ohm load options for the 4x12 cabinet are 16 ohm mono, 8 ohm stereo, and 4 ohm mono. Trouble shooting: Q: What is the manufacturer’s warranty for SV? A: The warranty for the Spider Valve amplifier is 12 months from the date of purchase, the tubes are warrantied for 90 days from the date of purchase. Q: How do I perform a factory reset on my Spider Valve? A: The factory reset for the Spider Valve series is to hold the "A" button while powering the unit. Q: Will using different brands of 6L6 tubes in the Spider Valve void the warranty? A: No, feel free to experiment with other tubes of the same type. Q: My amp seems to be malfunctioning. What can I do as an end user? Amp Troubleshooting Tube Troubleshooting and Replacement *Q: Where can I download a Spider Valve manual? Line 6 Manuals Miscellaneous Q: Where can I get a cover for my Line 6 amplifier? Cases And Covers Q: In the manual's explanation of how to save patch and perform 'NAME EDIT' with the FBV shortboard: Page 45, it states to use the 'COMP' & 'MOD' button to select one of the characters of the channel name. I don't see a COMP button, what should I use? A: Please use the 'STOMP' & 'MOD' button to select the characters from left to right. This was an error in the manual due for revision. Spider Valve Preset Patches.pdf

The GearBox Gold Plug-In Bundle contains the same models that are found in Line 6's flagship product, the Vetta II, plus it adds the Bass Expansion model pack. In essence, the Gold Bundle includes every model that Line 6 offers. The Silver Bundle had the same standard set of amp models found in the GuitarPort and TonePort. Some of the models included with the PODxt family of devices are not found in the TonePort, GuitarPort or the Silver Bundle unit. As of August 1st, 2008, all TonePort DI-Silver Bundle devices receive a complimentary free update to Gold Bundle status. Below is a brief summary of how model pack combinations added to the GuitarPort, TonePort or Silver bundle devices compare to those devices that include more models: Power Pack models update the GuitarPort/TonePort/Silver/POD Studio model set to match the PODxt/PODxt Pro model set. Power Pack and the FX Junkie model packs update the GuitarPort/TonePort/Silver model set to match the PODxt Live model set. Power Pack, plus the FX Junkie, Collector Classic, and Metal Shop (collectively known as the Triple Pack) model packs update the GuitarPort/TonePort/Silver model set to match the Vetta II model set. Power Pack, the Triple Pack and the Bass Expansion models update the GuitarPort/TonePort/Silver/POD Studio model set to match the Gold Bundle model set. The model sets used with the GuitarPort, TonePort and PODxt family devices are not VST plug-in ready when purchased. The online purchase and activation of the POD Farm 2.5 plug-in is necessary to use them as plug-in effects in a DAW/recording program. Q: Can I put guitar model packs or licenses for POD Farm or Gearbox plug-ins onto a Bass PODxt? A: No, the Bass POD units cannot install additional model packs or licenses for those programs. Q: Can I purchase model packs and /or plug-ins without a credit card? A: Our accounting system is only set up to accept transactions with a credit card. This includes the prepaid type.

Francais. Deutsch. If you are having trouble with your Line 6 amplifier, please check the following points before taking your amplifier to your local Authorized Service Center: Q: I am noticing that I am getting volume/tone changes when playing at a high volume? A: Try "parking" the knobs (except master volume) at 100% to ensure that the knobs are not moving to the "current" location rather than the preset location. Recall a preset once the knobs are parked to ensure the tone you are working with is a preset rather than the current knob position. Q: My master volume has almost no change past 6? A: This is due to the volume pot installed on all Line 6 amplifiers. A solution to this would be to replace it with an "audio" pot, but this modification wouldn't make it louder - just smoother. Line 6 originally installed audio pots on the AXSYS, but players didn't like them because they made the amp feel "wimpy". Players also did not like the fact that they had to turn the amp up to about 4-5 before it would start "happening" and 7-8 on the gig. Even though there was still a good amount of headroom, player feedback was that they preferred the amplifier with the traditional volume pot, so that is the style used with Line 6 amplifiers. - Perform a factory reset of the unit: Factory Reset Procedures Volume and Signal Troubleshooting - turn off other volume controls not being used (i.e. volume trim pots) - Ensure there is no debris in the CAT-5 or input jacks. - Unplug all other units from the audio chain, as well as any CAT-5 cables and controllers. - Use a high-quality cable you know is functional (i.e. works in a different application) directly into the instrument input, bypassing all other effect units. - Ensure that the guitar/bass is outputting signal. Try the amplifier with another instrument you know is functional (if possible).Make sure all the input and output jacks are tight. Check the instrument with different pickup settings to make sure it is not a bad pickup connection. - Ensure that both the positive (white) and negative (black or red) wires are fully connected to the speaker, and that the speaker output from the amplifier is plugged into the correct jack (when applicable). - Check the effects loop (if the amp has one). If you're not getting any signal, try plugging into the RETURN side of the loop to see if there is any output. Likewise, with a source feeding the input, plug the SEND into another line level device to see if you're getting signal. Tone and Rattle Troubleshooting - Check the make sure all buttons on the unit are not stuck - Be sure that all screws on the unit (handle, corners, baffle boards, speakers) are snug. - Ensure that there are no foreign objects (i.e. silicon packs) stuck in the speaker enclosures Q: Are the tone controls on the on a Line 6 amplifier passive or active, and where is the "flat" level? A: Each amp model is different, and the controls behaves like the target amp. Most tube amplifiers will have a passive tone stack with makeup gain. Line 6 tone stacks are designed to behave just like the modeled amp (both the good and the not so good). Some amplifier tone stacks are the closest to flat when set B-0, M-10, T-0, but it is different for each model. Power Troubleshooting - Ensure that there is sufficient power coming from the power outlet into the amplifier. Try a different circuit to ensure there is not a power issue at the outlet. - Make sure that the both ends of the power cable are snug in their sockets. Tube Amplifiers Troubleshooting - Make sure the tube is firmly seated in the tube socket. - If the tube(s) make a popping sound accompanied by intermittent light from tubes, the tube is failing and needs to be replaced. - If there is "white frost" inside the tube, the tube has cracked and it must be replaced. - If there is a "tube" ringing (not due to loose screws), there may be a failing tube. Replace the 12AX7s individually and the matched 6L6 pairs to determine if a tube has failed. Replacing Tubes - Always replace power amp tubes with matched set(s) every 12-24 months depending on the amount of use, and have the bias checked and/or adjusted by an authorized Line 6 Service Center. - Preamp tubes (such as the two 12AX7s) only need to be replaced when they are microphonic (ringing sound from tubes when tapped), noisy, or damaged. Replacing tubes should be done a Line 6 authorized service center. The digital stage and analog tube stages communicate with one another, and so are not like the all analog tube (valve) amps from the 1960's and 70's. As a result, one cannot swap tubes out like in the old days. So please use the following specified tubes (valves) when the amp is taken to a service center. For Spider Valve series amps use the following specified tubes, 12AX7B China for pre-amps. 5881WXT Sovtek (matched pair), with the base cup bottom. 5881WXT Sovtek (matched quartet), with the base cup bottom for the HD-100 and HD100 MkII. For the Alchemist series amps use the following specified tubes, 12AX7EH Electro-Harmonix low microphonic for V1-3 pre-amp positions. 12AX7AC5HG Ruby Tube HG-High Gain for V4. 12AX7B China for V5. 6L6GCMSTR Ruby Tube (matched pair) power amp. For the DT50 series amps use the following specified tubes, 12AX7EH Electro-Harmonix approved for the DT50 pre-amps. EL34EH Electro-Harmonix (matched pairs) for the power amps. For the DT25 series amps use the following specified tubes, 12AX7EH Electro-Harmonix approved for the DT25 pre-amps. EL84EH Electro-Harmonix (matched pairs) for the power amps. Visit your local Line 6 Service Center for servicing a tube amp, as these have High Voltage Shock Hazards. Product Repair Si vous avez des problèmes avec un des amplis Line 6, vérifiez les points suivants avant de retourner l’ampli. J’ai des changements de son si je joue à un volume très fort. Pourquoi ? Laissez tous les boutons sur 100% excepte le Master Volume pour assurer que le bouton ne tourne pas à la position courante mais à la position du preset. Démarrez un preset pour assurer le ton est le propre. Presque rien ne se passe si je tourne le Master Volume passe 6, pourquoi ? C’est à cause du potentiomètre installé dans les amplis Line 6. On pouvait installer un potentiomètre audio qui ne changerait pas le volume. Line 6 a essayé d’installer des potentiomètres audio mais les joueurs ne l’ont pas aimé. Dépannage de volume et signal : Éteignez les autres contrôles volumes comme les potentiomètres Volume Trim. Assurez qu’il n’y en a pas du débris dans les jacks CAT-5 ou entrée. Débranchez tous les autres appareils de la chaine audio aussi bien que tous les câbles CAT-5. Utilisez un câble que vous savez qu’il fonctionne directement dans l’entrée, contournant les effets. Assurez-vous que la guitare ou basse produit un signal. Essayez un autre instrument que vous savez fonctionne. Vérifiez tous les jacks d’entrée et sortie. Essayez l’instrument avec autres micros pour vérifier que ce n’est pas un micro défectueux. Vérifiez les câbles blanc et noir ou rouges connectés au haut-parleur. Vérifiez la sortie du haut-parleur du ampli est branché correctement. Vérifiez la boucle d’effets, si vous ne recevez aucun signal, branchez le dans le RETURN. Avec une source dans l’entrée, branchez le SEND dans le Line In d’un autre appareil pour vérifier le signal. Dépannage hochet et ton : Vérifiez si un des boutons et collé. Toutes les vis doivent être serrées. Assurez vous qu’il n y en a aucun objet étranger dans haut-parleurs. Est-ce que les contrôles sur l’ampli Line 6 sont passifs ou actives ? Et ou est le niveau « flat » ? Tous les modèles sont différents et les contrôles changent pour chaque modèle. La plupart des amplis à tubes sont passives. Le ton des amplis Line 6 sont conçus pour se comporter exactement comme l’ampli modelé. Quelques modèles sont très près de « flat » sur B-01, M-10 et T-0 mais c’est différent pour chaque modèle. Dépannage alimentation: Assurez-vous qu’il y en a assez de courant pour l’ampli. Vérifiez lé prise de courant. Vérifiez le câble et les connecteurs. Dépannage des amplis à lampes : Vérifiez que le tube est bien assis dans la douille. Si le tube fait des sons popping avec de la lumière intermittente. Vous devez remplacer le tube. S’il y en a de gelée blanche dans le tube, vous devez le remplacer. Si le son sonne c’est possible qu’un des tubes est défectueux, remplacez les tubes individuellement. Remplacement des tubes : Remplacez les tubes tous les 12 à 24 mois selon l’usage. Et laissez vérifier/ajuster le Bias d’un centre service Line 6 autorisé. Les tubes de préampli doivent uniquement être changés s’ils sont microphoniques endommagés ou bruyant. Si vous avez des problèmes après toutes ces suggestions, veuillez visiter un centre service Line 6 s.v.p. mais n’oubliez pas la preuve d’achat si vous êtes dans les 12 mois de garantie. Réparation des produits Sollten Sie Probleme mit Ihrem Line 6 Verstärker haben, dann überprüfen Sie bitte erste die Folgenden Punkte bevor Sie sich an ein Line 6 Service Center wenden: Ich kann Ton/Lautstärkeänderungen feststellen wobald ich sehr laut spiele, woher kommen diese? Stellen Sie die Knöpfe, abgesehen vom Master Volume auf 100% um sicherzustellen, dass diese sich nicht zur derzeitigen Position bewegen sondern auf der Position des Presets bleiben. Starten Sie dann ein Preset um zu überprüfen ob der Ton der des Presets und nicht der der derzeitigen Position des Knopfes. Mein Master Volume verändert die Lautstärke beinahe nicht nach 6, warum? Dies liegt am installierten Potentiometer, Line 6 hat in frühen Modellen mal einen Audio Potentiometer ausgetestet aber den Spieler gefiel dieser nicht. Lautstärke und Signalproblembehebung: Schalten Sie andere Lautstärkeregler ab (Trim Pots zum Beispiel). Stellen Sie sicher, dass kein Dreck im CAT-5 Eingang oder anderen Jacks ist. Entfernen Sie alle anderen Geräte und Cat-5 Kabel aus der Kette. Benutzen Sie ein Kabel, von dem Sie wissen dass es funktioniert und schließen Sie es direkt zwiscen Gerät und Instrument, umgehen Sie so alle zusätzlichen Effekte. Stellen Sie sicher, dass Ihr Isntrument ein Signal abgibt. Versuchen Sie falls möglich ein anderes Instrument von dem Sie wissen, dass es funktioniert. Versuchen Sie unterschiedliche Tonabnehmereinstellungen. Stellen Sie sicher, dass das weiße sowie das schwarze bzw. rote Kabel korrekt an den Lautsprecher angeschlossen sind. Überprüfen Sie außerdem den jack des Lautsprechers. Überprüfen Sie den Effects Loop, falls vorhanden. Wenn Sie kein Signal bekommen, dann versuchen Sie diesen in den RETURN zu stecken um zu sehen ob Sie ein Signal bekommen. Genauso sollten Sie auch den SEND in ein anderes LINE IN Gerät stecken. Ton und Rassel Probleme: Überprüfen Sie alle Knöpfe um zu sehen ob einer feststeckt. Überprüfen Sie ob alle Schrauben fest angezogen sind. Stellen Sie sicher, dass keine unerwünschten Objekte im Kautsprecher sind. Ist die Tonsteuerung aktiv oder passiv? Und wo ist die flach Einstellung? Jedes Modell ist unterschiedlich und die Steruerung des Verstärkers verhält sich so wie die des modellierten Verstärkers. Manche Modelle sind sehr flach, wenn sie auf B-01, M-10 und T-01 eingestellt sind, dies trifft aber nicht unbedingt zu da dies auch unterschiedlich ist zwischen den verschiedenen Modellen. Röhrenverstärker Problemlösung: Stellen Sie sicher, dass die Röhren fest im Sockel sitzen. Sollten die Röhren ein Poppen machen und dazu unterbrochen leuchten, dann ist diese kaputt und muss ersetzt werden. Falls weißer Frost in der Röhre ist, dann hat diese en Loch und muss ebenfalls ersetzt werden. Sollte ein Röhre klingeln, könnte es sich auch um eine kaputte Röhre handeln. Ersetzen Sie dann die Röhren einzeln um festzustellen, welche kaputt ist. Röhren ersetzen: Lassen Sie Röhren immer mit passenden Sets alle 12 bis 24 Monate je nach Nutzung ersetzen und lassen Sie den Bias von einem autorisierten Line 6 Service Center überprüfen bzw. anpassen. Vorverstärker Röhren brauchen erst dann ersetzt zu wernden, wenn sie mikrofonisch oder rauschend klingen bzw. beschädigt sind. Sollten Sie dann immernoch Probleme mit dem Verstärker haben besuchen Sie bitte ein Line 6 Service Center. Vergessen Sie aber nicht den Kaufbeleg falls Sie sich noch in den 12 Monaten der Garantie befinden. Produktreparatur

Phantom power is DC (or direct current) used to power certain microphones, the UX2 and KB37 offer 48-Volt signal to a condenser microphone by connecting it to the XLR input on the unit. The UX1 does not have phantom power, if you have a microphone that requires such power you will need to get either a standalone microphone preamplifier or one that is built into an audio mixer's input channel. Also available are stand alone phantom power boxes. (A good example of this device is the Rolls PB23 Phantom Power Supply). Phantom power is not harmful to mics that don't need it. If a mic does not need phantom power it will ignore the 48-Volts being sent the the microphone. Even with the Phantom Power on, your UX2 or KB37 can have both a mic that requires Phantom Power and a mic that does not require Phantom Power.

Français Deutsch Q: Which power supply works with each Line 6 device? Line 6 power supplies are available at your local dealer or at our Online Store. Q: I want to power more than one Line 6 unit from the same power supply. How can I achieve this? A: The Voodolab Pedal Power II Plus can power up to 6 Tonecore pedals and two Modeling pedals at once, and the Voodoo Lab Pedal Power AC can power up to four Modeling pedals. Other power supplies may not deliver consistent voltage and are not supported by Line 6. Voodoo Lab Pedal Power 2 Plus Voodoo Lab Pedal power AC To power the early Line 6 "modeler pedals" (DL4, DM4, FM4, MM4, etc) with Pedal Power 2 Plus, use output 5 or 6, DIP switch AWAY from normal with the supplied red/black ended cable (it's 2.1mm/2.5mm reverse polarity and the red end fits the effect pedal). The reason this works is that the actual current draw* of these early modeler pedals is less than 250mA. Also, when DC power is used, 12V is required (as opposed to 9V when AC power is used). *It is quite common for effects/pedals to be labeled to match the specifications of some included/OEM power supply (as labeling them differently can often times confuse the end user). When however, in reality, these effects/pedals will have an actual current draw (mA) that is (far) less than this specified/labeled value. Note: sometimes, the actual current draw can be found in the manual (appendix/specs). Q: I am traveling overseas. How should I power my Line 6 device? A: You can buy any adapter that converts your country's power to these specs and it will work. Any electronics store in your country should be able to sell you one, or you can contact your local Line 6 dealer. Be aware that the DC-1g and DC-3g power supplies are universal across all voltage and power standards around the world, and you will only need the appropriate adapter for a new region rather than a different power supply or transformer. There are certain products that operate over a range of power supplied and don't require any conversion: Helix Floor/Rack/LT, Powercab 112/112 Plus, all Catalyst amps, Firehawk 1500: 100-240V AC Relay G90: 90-250V AC POD HD Pro/Pro X: 100-240V AC POD X3 Pro: 100-240V AC Q: What if I do not have the Line 6 power supply? A: If it is not possible for you to obtain an official Line 6 power supply, then any other power supply with the same specifications should suffice (but is not supported). Q: I am outside the United States, what do I need to power my Line 6 unit? Option 1: We recommended that the proper Line 6 power supply be used. Please contact an authorized Line 6 Distributor for the appropriate region. To acquire the proper Line 6 power supply for a desired country, please visit the Authorized Line 6 Dealers page to find an one near you. Option 2: You will need a travel voltage converter. These will work with our products provided they output the currents and voltages specified on your Line 6 devices or power supplies. Q: I purchased my internally powered Line 6 unit in a region that has "XXX" voltage, and now I am relocating to a region that has different power. Can my Line 6 unit be modified or do I need to use a external transformer? A: Many Line 6 products can be internally modified at an Authorized Line 6 Service Center to the power needs in your new region. Spider amplifiers require that the transformer be replaced along with internal modification. Please note that this is a non-warranty modification and will not be covered under any warranty agreement. Q: What are some of the common power situations around the world? A: Always verify your voltage and frequency BEFORE plugging your unit in, as damage could result if the unit is improperly powered. Although there can be variations to power, here are some common voltage and frequency situations found around the world: United States: 120V AC/60 HZ Europe: 230V AC/50Hz United Kingdom: 230V AC/50Hz Australia: 230V AC/50Hz Japan: 100V AC/60Hz Here are some examples available on the web: https://en.wikipedia.org/wiki/Mains_electricity_by_country http://www.world-import.com/all-transformers.htm Q: What is the U.S. warranty on a Line 6 power supply? A: 90 days from the purchase date. This applies to power supplies purchased separately and were not included with a Line 6 device. Q: What is the difference between alkaline and rechargeable batteries? A: Rechargeable batteries will usually last about half the time of alkaline batteries, and can have an inconsistent power drain after each recharge. We recommend using alkaline batteries when powering your Line 6 product. Not all rechargables are true AA size and may not fit correctly. Quelle alimentation pour quel appareil Line 6? Vous pouvez acheter les alimentations du revendeur. Je veux alimenter plus qu’un seul appareil avec une alimentation, comment est-ce que je réalise ca ? Le Pedal Power II Plus de Voodoo Lab peut alimenter jusqu'à 6 pédales Tonecore et 2 pédales modélisations en même temps. Et le Pedal Power AC de Voodoo Lab peut alimenter jusqu'à 4 pédales de modélisation. Autres alimentations ne sont pas soutenues de Line 6. Voodoo Lab Pedal Power 2 Plus Voodoo Lab Pedal power AC Je suis à l’étranger, comment est-ce que je peux alimenter mon appareil Line 6 ? Vous devez acheter un convertisseur ou contacter votre revendeur Line 6. L’alimentation DC-1g est universel donc vous n’avez pas besoin d’un transformateur ou une autre alimentation, seulement d’un adaptateur. Il y en a quelques appareils qui n’ont pas besoin d’un transformateur : POD HD Pro 100-240V AC, POD X3 Pro 100-240V AC, Relay G90 90-250V AC. Contactez un des revendeurs officiels de Line 6 si vous avez besoin d’une alimentation différente : www.fr.line6.com/support/dealers/ Et si je n’ai aucune alimentation Line 6? Qu’est-ce que je fais ? Si vous n’avez pas d’accès à une alimentation Line 6. Une alimentation de tires fonctionne aussi, si cette alimentation a les mêmes spécifications. Attention, ces alimentations ne sont pas soutiens de Line 6. J’ai acheté un appareil Line 6 avec alimentation intégrée et maintenant je vais à l’étranger avec cet appareil, est-ce qu’on peut modifier mon appareil ou est ce que j’ai besoin d’un transformateur ? Beaucoup d’appareils Line 6 peuvent être modifiés à un centre de service Line 6 autorisé. Le transformateur des amplis Spider doit être remplacé. Attention, ces modifications ne sont pas des modifications en garantie, donc vous devez payer pour ceux. Attention, vérifiez la tension et fréquence AVANT de brancher les appareils. Ici quelques tensions : États-Unis: 120V AC 60Hz Europe: 230V AC 50Hz Australie: 230V AC 50Hz Japon: 100V AC. Est: 50Hz. Ouest: 60Hz. Quelle est la garantie sur les alimentations Line 6 ? 90 jours pour les alimentations achetés séparément. Quelle est la différence entre les batteries Alkaline et les batteries rechargeables ? Les batteries rechargeables durent environ la moitié du temps des batteries Alkalines. Et parfois, les batteries rechargeables ont un drain de puissance incompatible. Nous recommandons les batteries Alkalines pour les produits Line 6. Welches Netzteil brauche ich für mein Line 6 Gerät? Line 6 Netzteile konnen Sie bei Line 6 Handlern. Wie kann ich mehrere Line 6 Geräte an ein einziges Netzteil anschließen? Das Voodoolab Pedal Power II Plus kann bis zu 6 Tonecore Pedale und 2 Modeling Pedale mit Strom versorgen und das Voodoolab Pedal Power AC kann bis zu 4 Modeling Pedale mit Strom versorgen. Andere Netzteile könnten eventuell keine beständige Voltzahl liefern und sind nicht von Line 6 unterstützt. Voodoo Lab Pedal Power 2 Plus Voodoo Lab Pedal Power AC Ich reise ins Ausland, wie kann ich dort meine Line 6 Geräte mit Strom versorgen? Sie können sich einen Adapter kaufen, der den Strom im Ausland in den Ihres Heimatlandes umwandelt. Jeder Elektronikladen sollte diese Adapter verkaufen, ansonsten können Sie auch Ihren Line 6 Händler kontaktieren. Der DC-1G ist universal verwendbar, für dieses Netzteil brauchen Sie also nur Adapteraufsatz und kein neues Netzteil oder Transformator. Manche Geräte laufen auf mehreren Voltzahlen: POD HD Pro 100-240 Volt Wechselstrom. POD X3 Pro 100-240 Volt Wechselstrom. Relay G90 90-250 Volt Wechselstrom. Spannungswandler müssen 1,5 A und 100 Watt minimum liefern können. Was kann ich tun wenn ich kein Line 6 Netzteil zur Verfügung habe? In diesem Fall können Sie auch jedes andere Netzteil verwenden, welches die oben angegebenen Spezifikationen hat. Diese Netzteile werden nicht von Line 6 unterstützt. Ich habe ein Line 6 Gerät mit internem Netzteil. Wenn ich nun aber in eine Region umziehe, in der die Spannung eine andere ist, kann ich mein Line 6 Gerät auch umbauen lassen oder brauche ich einen Transformator? Viele Line 6 Geräte (wie Rack-PODs, Flextone oder Vetta) und Verstärker können von autorisierten Line 6 Service Centern modifiziert werden um der benötigten Spannung zu entsprechen. Spider Verstärker brauchen einen neuen Transformator. Diese Modifikationen sind nicht in der Garantie enthalten, Sie müssen also für sie bezahlen. Gebräuchliche Stromspannungen und Frequenzen: Vereinigte Staaten: 120V, AC, 60Hz. Europa: 230V, AC, 50Hz. Australien: 230V, AC, 50Hz. Japan: 100V, AC, Osten: 50 Hz Westen