Search the Community
Showing results for tags 'block'.
Found 6 results
-
Is there a way to ADD an EXTERNAL Compressor Pedal into an EX LOOP Block on HX stomp , Yet still retain the main SEND JACK to route signal to a stage amp? -
If you've installed a Line 6 driver and the device will not subsequently connect, it is possible that the driver is disabled by the system. How to check if the software is disabled by the system: • Click on the Apple symbol in top-left corner of the screen and go to "About this Mac -> Overview ->System Information -> Disabled Software”. • If there is disabled software, it will be presented with a 10-digit software ID and a file descriptor, similar to "VCN535JA6Y - com.line6.driver.xtaudio" • Take a screen shot or write down the ID (in this example it’s VCN535JA6Y – yours might be different). How to enable software that is disabled by the system: • Uninstall the drivers: https://line6.com/support/page/kb/recording/computer-audio-set-up-and-troubleshooting/how-to-uninstall-line-6-drivers-from-mac-osx-r85/ • Reboot to recovery, holding down Command-R while restarting. • From Menu -> Utilities, open Terminal and type the following (replacing the system ID with yours): “spctl kext-consent disable” “spctl kext-consent add VCN535JA6Y" (replace the VCN535JA6Y with yours if different) “spctl kext-consent enable" • Reinstall the driver. • Open System Preferences -> Line6 Audio-Midi devices and plug the device into the Mac. The device should appear in a few seconds. -
Hello all, I'm looking for help with my setup. I'm not sure if this is a wiring issue or perhaps a hx stomp block chain issue. I just bought a BOSS SY1 synth pedal. I want to isolate the GUITAR (dry) signal from the SYNTH signal. I think I have most of this figured out but there's some things that are baffling me. I'm using 4 things * Guitar * Boss SY1 * L6 HX Stomp v2.92 * FRFR Speaker How its hooked up (all of 4 cables) Guitar output > Boss SY1 input (I want this pedal in the front as it tracks better) Boss SY1 "SEND" > HX Stomp main input L - this is the 100% DRY signal (works regardless if the SY1 is on or off) Boss SY1 "OUTPUT" > HX Stomp Aux In L - this is the 100% SYNTH signal as set by the SY1 direct and effect volume settings HX Stomp block chain - Main Input L > Overdrive block > Amp & CAB block > RETURN L block (from SY1 OUTPUT jack) > Delay block > Reverb block > Main Output (to FRFR speaker) My thinking in this was I can have my normal guitar amp and cab sounds and then to insert the synth sound just before the delay and reverb blocks so everything can use those, using the RETURN blocks mix to adjust how much of dry/synth signal I want. Sometimes 50/50 dry/synth and then sometimes 100% synth. The issue I'm having is this setup works fine but the RETURN L will not use the delay and reverb blocks, despite it being in front of both of them. The amp and cab blocks which are before the RETURN L use the delay and reverb which is baffling me. I can not tell what I'm doing wrong here. Any guidance would be much appreciated. I feel I'm close but obviously missing something here... Much thanks in advance!
-
I am having an issue where multiple foot switches are showing multiple assignments > for example, the scribble says - MULTIPLE (3) - but withing this preset, i have only assigned one block to each foot switch. If I enter Signal Flow, and delete each effect one at a time, then hit home, each FS still has an assigment of MULTIPLE (2) or MULTIPLE (3). When I hit the action button, the 'CLEAR BLOCK' is greyed out. How can I clear out everything from a preset with one action?
-
How do you use midi to turn on/off an effect? I see how to change the parameters of an effect but not how to enable/disable the effect block. Any ideas?
-
In the AMPLIFi Remote editor, there are 10 effects blocks that you can turn on and off, and assign different models and parameters to. Some of them can be dragged to different locations, some can't. Of these ten blocks, only three of them can be assigned as: Drives and Dynamics Mods Delays Filters, Synths and Pitch A quick way to tell which three can be assigned these effects types is that they have a border around them: Notice Stomp, Synth and Mod all are bordered. However, Reverb is selected, so its border is brighter. Here's how to change the effect type of those three blocks: 1. Select one of the three blocks by touching it. In this example, we'll select Stomp. 2. The effect will then show the effect type (in this case, "stomp"), the effect name ("Facial Fuzz"), and a power button to the right to turn the effect on or off. Touch the effect type to change it. 3. You'll then see a "Type" button. Touch it. 4. The block types then appear. Choose one. 5. Lastly, select an effect and touch OK. 6. The block has been changed. There is no restriction on the number of similar effect types or effects assigned to these three blocks. Three stomps, each with a Fuzz Pi on it? Knock yourself out! Just don't forget to save your tone (cloud icon, then disc icon).
