Please ensure Javascript is enabled for purposes of website accessibility Jump to content

Search the Community

Showing results for tags 'output mix'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Community Support
    • Multi-Effects Units
    • Variax Instruments
    • Amplifiers
    • Computer Based Recording
    • Live Sound
    • Pedals/Controllers
    • Dream Rig - Line 6 Product Integration
  • General Discussion
    • Tone Discussion
    • Line 6 Lounge

Categories

  • General FAQ
    • Operating System-specific Information
  • Tutorial Videos
  • Effects/Controllers
    • HELIX/HX
    • DL4 MkII Stompbox Modeler
    • FBV Controllers (MKII / 3)
    • M5
  • Amplifiers
    • Powercab
    • Catalyst
    • Spider V
  • POD
    • POD Go
    • Pocket POD
    • POD Express
  • Guitars
    • JTV / Shuriken / Variax Standard / Workbench HD
  • Relay/XD-V Digital Wireless
  • Recording
    • Helix Native
    • Metallurgy
    • Echo Farm/Amp Farm
    • POD Farm 1/2.0/2.5
    • Computer Audio Set Up and Troubleshooting
  • Legacy Products
    • POD
    • Amps
    • 1st Gen Variax Guitars / Bass / Workbench
    • Effects and Controllers
    • AMPLIFi Series
    • Live Sound
    • Digital Wireless
    • Mobile Products
    • POD Studio / Tone Port / GuitarPort
    • Software
    • Dream Rig

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Location


Interests


Registered Products

Found 2 results

  1. Hello, I just got my Helix floor, and try to figure out the following setup: I want to use it live for my guitar *and* vocals and have the signals independent. So the Upper Chain should be: Git In => XLR Left and the lower chain MIC In => XLR Right. As I can only assign XLR out (and not XLR Left / Right) I was assuming panning the XLR out of the upper chain all the way LEFT would cause the signal to go to the XLR Left out only. And if I'd pan it all the way Right, there should be no signal through XLR Left at all (because all goes to right). But panning to left or right just lowers the volume of the signal and there is no difference between panning it to the left or panning it to the right. So it seems to me, that there is some "Stereo to Mono Summation" or something like this happening. I was looking for a "set XLR to Mono" Switch but found nothing. I have not changed the setting of the Helix, just updated the firmware to 03.11. My test setup is just the guitar in and XLR out LEFT => Audiointerface. The upper chain has Guitar In Input and XLR output, the lower chain has MIC In and XLR out (though I did not connected any cables to MIC IN and XLR Right yet). Any idea, how I can fix this? Thanks in advance, Frank
  2. Hi there! Here's what I'm trying to do: 1) Create a clean signal that will play straight through, center pan. Easy. 2) Take the same signal and run it panned hard left through a delay and pitch transposer where the wet only signal plays 260ms AFTER the original signal, dropped -7th via pitch but no original note, only the -7th, panned hard left. 3) Using the same original signal, run it panned hard right through a delay and pitch transposer where the wet only signal plays 520ms AFTER the original signal, raised +5th via pitch but neither the original signal nor the left dropped 7th coming through. Center, then hard left dropped a 7th, then hard right raised a 5th. Three notes, not overlapped. Center, left, right. This is day one with my new POD HD PRO X. Thank you!
×
×
  • Create New...