Please ensure Javascript is enabled for purposes of website accessibility Jump to content

Search the Community

Showing results for tags 'pod500x'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Community Support
    • Multi-Effects Units
    • Variax Instruments
    • Amplifiers
    • Computer Based Recording
    • Live Sound
    • Pedals/Controllers
    • Dream Rig - Line 6 Product Integration
  • General Discussion
    • Tone Discussion
    • Line 6 Lounge

Categories

  • General FAQ
    • Operating System-specific Information
  • Tutorial Videos
  • Effects/Controllers
    • HELIX/HX
    • DL4 MkII Stompbox Modeler
    • FBV Controllers (MKII / 3)
    • M5
  • Amplifiers
    • Powercab
    • Catalyst
    • Spider V
  • POD
    • POD Go
    • Pocket POD
    • POD Express
  • Guitars
    • JTV / Shuriken / Variax Standard / Workbench HD
  • Relay/XD-V Digital Wireless
  • Recording
    • Helix Native
    • Metallurgy
    • Echo Farm/Amp Farm
    • POD Farm 1/2.0/2.5
    • Computer Audio Set Up and Troubleshooting
  • Legacy Products
    • POD
    • Amps
    • 1st Gen Variax Guitars / Bass / Workbench
    • Effects and Controllers
    • AMPLIFi Series
    • Live Sound
    • Digital Wireless
    • Mobile Products
    • POD Studio / Tone Port / GuitarPort
    • Software
    • Dream Rig

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Location


Interests


Registered Products

Found 2 results

  1. So I just got a new amp that finally allows me to use the 4cm. I have a blackstar HT 60 which is an amazing amp and I am using my POD 500x to run fx pre and post. My problem becomes that I get a slight hum whenever I insert the FX block into the chain. This hum stays even when I take the fx block into bypass mode or off and the hum stays it does not leave until I have the FX block deleted from the chain. I am unsure if this is an amp issue or Pod. I believe it to be the POD as this only happens when the FX block is added and is in bypass or off mode. I can put a noise gate up to block most of it but when you play you can faintly hear the hum underneath etc. I have used the 3cm method as that is what the Line 6 people recommended because I do not use amp modeling and this did allow me to use the three built in channels on the amp but then from what I have learned and messed with is that I lose the ability to put compression etc in front of the pre amp of the ht 60. I did manage to get the hum softer by not having those cables from the amp fx send and return not run parallel and have now upgraded those cables to balanced to also combat the signal hum but the hum is still slight and annoying. I would like to be able to run the amp as quiet and clean as possible without having to worrying about having enough blocks for the FX block, Noise gate etc. That eats up two blocks when I would much rather have it run as one block. Does anyone else have this same problem or have any insight of something to try to help combat this? Thanks
  2. This is a little hard to explain because I'm not a native speaker, but I'll do my best. When I have my PodHD500x in the ABCD (FS) mode I can change between the 4 patches of the bank. What is a problem for me is that when I'm in a patch and I edit it using the FS1-4 switches, and change to other one, and then I return to the first patch, it would go back to the original settings. Is there a way in which I can change between patches in ABCD mode and they don't return to original settings if I edit them with the FS1-4 buttons? I've seen that this same thing does happen when I have the pod connected to the pc editing mode with the software. But it doesn't work when is not connected. If this could be posible, i would be so grateful. I hope I make myself understand. Thanks for any help you could give. Have an awesome day.
×
×
  • Create New...