Jaguar9080 Posted February 11, 2015 Share Posted February 11, 2015 I thought I remembered reading this somewhere before, but I can't seem to find it again and searching the forum didn't return any applicable results. It's not in the "pilots guide" for the amp either. Is there a way to set the default volume for the main volume and guitar volume when the amp starts up? What I'm looking for is for the guitar volume to be at 40% and the overall volume to be around 60% each time I turn the amp on. Right now the amp starts with the guitar volume at 75% and the overall volume at 20%, which is how it's been since I first bought it. Quote Link to comment Share on other sites More sharing options...
wilson69978 Posted February 13, 2015 Share Posted February 13, 2015 I have not seen anything regarding this issue either. If you find anything out could you post it please? Thanks Jaguar 9080 Quote Link to comment Share on other sites More sharing options...
pberrin Posted February 25, 2015 Share Posted February 25, 2015 Hi, Did you find out how to set the default volume ?Mine is starting up with a lound cracking sound, the guitar volume at 100% and the overall volume at 30% :-((( Thanks Quote Link to comment Share on other sites More sharing options...
Jaguar9080 Posted February 26, 2015 Author Share Posted February 26, 2015 Doesn't seem like anybody knows... Quote Link to comment Share on other sites More sharing options...
wilson69978 Posted February 27, 2015 Share Posted February 27, 2015 Well, I give up too. I suspect this is to protect the speaker in the unit so that it does not come on at too loud a level and blow out the speaker. With certain effects chains and levels set high you can get very serious loudness from these amps. Quote Link to comment Share on other sites More sharing options...
burreddog Posted March 12, 2015 Share Posted March 12, 2015 Jaguar9080 Mine starts up at about the same volume levels that you described. I haven't found a way to change it either. Will post if I do. I wouldn't mind if it kept the same settings as when I shut the amp down. Quote Link to comment Share on other sites More sharing options...
awgoldsby Posted March 20, 2017 Share Posted March 20, 2017 I will chime-in here in hopes of helping to get attention to this topic, and a reply. I agree, it would be a great feature to have the amp start up at the volumes setting when last used. I've been looking for an answer for over a year. Quote Link to comment Share on other sites More sharing options...
shaggydawg Posted April 8, 2017 Share Posted April 8, 2017 I just made a new post asking the same question. Guess I should have searched the forum first. I agree, it's probably some safety feature since the default overall level is around 16%. Quote Link to comment Share on other sites More sharing options...
JimmyTheSaint Posted May 2, 2017 Share Posted May 2, 2017 http://line6.com/support/topic/24826-how-to-specify-startup-volumes-levels/ Quote Link to comment Share on other sites More sharing options...
jdavidboyd Posted May 8, 2017 Share Posted May 8, 2017 Everything I've tried has not worked. Quote Link to comment Share on other sites More sharing options...
SteveJohns Posted July 18, 2023 Share Posted July 18, 2023 I have inquired of LIne 6 support, in July of 2023. There is no way to configure the default startup volume(s). It would require a firmware change. Needless to say, this is highly unlikely on these discontinued products. Nevertheless, I will add that it would be a truly noble and helpful thing for LIne 6 to do for the exisiting user base. That and adding a way to save and load entire banks of 100 from the Amplifi at once (like all other Line 6 amps, yes?). I didn't "get" the Amplifi design when it first came out, but eventually I did "get" it and now have 3 of them! If this product line wasn't the success that was hoped for (?), then it is because a) it was ahead of it's time, and b) it was just short of fully realized in the ways that real players need in their daily use. FWIW, I would comment to LIne 6 the following: A. Finish the job on the Amplifi line, firmware and software-wise. There will be no $$ profit in this, but the repair in goodwill will be tremendous. B. Create a new updated product line with the same basic ideas (FRFR, Bluetooth, control by app, great sounds) implemented with the latest and greatest of what you've got models and FX-wise. C. In the new line, make sure there is a knob to do bank select on the amp. Bank select should be available from ALL 3 of Amp, Floorboard, App - whatever the user has available or finds most convenient at the moment! That's what we need in the field. Thanks. Cheers! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.