ChrisClaytonLoop

Thanks for letting me know. I tried plugging the HX in by itself and the distributor would shut off. I have a doubtful feeling that it will work.

So I just got the HX Effects to replace my M9, along with other stomps from my pedalboard. I currently am running the gigrig generator to power everything except the m9, I am using the line 6 power supply for that. The guys at gigrig said the Generator should power everything, but when I hooked up my m9, the screen was all weird and patchy. The sound was fine, but I couldn't read the screen at all. I even plugged the generator alone into the m9 ans still the same thing. There was a lot of weird white noise when plugged in as well. I was hoping to use the generator with the HXFX, but I'm curious if anyone has had success with it, along with other pedals. I should list what I'm running. I have 2 buffers (I run 2 signals through the board, maybe I don't need them), a small 3 channel looper, Boss DD-6, Boss OC-3, Boss BF-2, Boss RC-300, and then the HX Effects. And where I have the hxfx located I dont like the power cord hanging off the top if the board, since the power supply is straight and not right angled.

This thing is really awesome Im barely able to grasp the possibilities yet. But I appreciate you guys being so quick and helpful. I figured out the SPLIT and MERGE, Left stats left, and Right stays right. The delay that I want to use with both, I just copy and paste it from A to B. I also set up an EQ for the percussion signal, which is even more helpful than the EQ I have on the board now. I'm still setting up everything I need, trying copy over all the scenes from my M9. I'm thankful for the Copy and Paste feature, makes starting off each new scene easier. And that I can set up an Expression toggle to any of the footswitches, which eliminates the need for Exp switch pedals I have plugged into the M9. Once I'm done with getting these scenes set up, and I get a long enough break between gigs so I can tear the board apart, then I can work on rerouting everything and moving some pedals around to get this bad boy on.

Oh ok. That makes it so much easier. And if I want the outputs to be the same way, then do that to the far right of the flow?

Ok so I got it, Trying to figure how to split the signals. And I'm trying to google it as I'm going. Is it the pan blocks? Do I need 2 one for left signal, one for right?

This is essentially the plan for now.

So the HX is obviously replacing the M9 in the upper left. The 2 green expression pedals in the upper right will go as well. And the EQ pedal will also go. But I know I can replace the flanger as well, I'll just have to set up the delay pedal next to it in an FX loop. I have two lines coming out of my acoustic, the normal preamp line, and then a percussion line which currently runs through the EQ and then mixes in. The guitar line runs through everything else then mixes in. My old board setup also had a DL4, which both went through that, so the percussion used the same delay because the lines ran stereo. And I want that again.

Ok. Thanks. Thanks a bunch guys. Ordered this Pandora's box today, so I'll be better her all setup soon, and will let you guys know how it goes. Going to have to get all these things sorted before I can drop it on to the pedalboard and pull off what it's replacing.

So if I need 2 blocks for A, then that leaves only 7 for B? And if I used a stereo delay, I can't keep the A and B outputs separate?

Ok good to know. Thanks for confirming everything for me. If I have these 2 signal chains, do I get 9 blocks for each of them? So split L and R, does each side get 9? One line only would use a couple effects anyway, EQ and the delay. Will those take away from the other side?

Okay. I understand that. I want to keep the outputs separate on each line. What if I set up a delay block on both signal flows, parameters identical, am I able to assign both delay blocks from both L and R to the same footswitch. So when I turn it on, both signals have delay turned on simultaneously?

I've seen posts about using 2 separate signals. And without playing around with I know it will take me a bit to figure out how to run the 2 separate signals. But if I want both signals to run through the same delay, am I able to have both signals run through the same delay block and then stay separate?

Hello everyone, Long time listener, first time caller. I have not pulled the trigger yet on the HX Effects, but I'm sure I'd be happy with the purchase regardless of whether or not there is an answer to my question. I have been looking around at forums, videos, reading the manual. But I haven't quite figured out the answer yet. And I dont have the unit in front of me to play around with either. My question: If I want to run 2 instruments into the HX Effects, and have one effect work on both lines, but then each signal have it's own effect chains, is this possible? I am sure this doesn't make as much sense as it does in my head. My current pedalboard I plug 2 signals in. They both have their own pedals they run through, but at one point in their chain they both run through my DL4. Left in/out is one signal, Right in/out is the other signal. Because I want both instruments to use the same delay, but dont want the second signal to run through distortion and other effects like that. I'm not sure if I could run both signals in the right and left, and be able to do all of this in signal flow. Or if there's another way. I'm curious if I can do all of that within the HX Effects. That would be able to replace most of my pedals and would help slim my board down even more.