BoatTox

This is if anyone is doing something similar, this is where I landed. Helix —> L6 cable (AES/EBU L6 Link Cable OUT) —> PC 112+ L6 Link AES IN. This lets my helix play to the power cab as I want without BB or Aeros. All forms of modeling from the PC and Helix (FRFS). BB—> 1/4 OUT L (mono) —> PC Line 1 IN 1/4 This lets me play BB alone, with helix, or with Aeros without contaminating the loops with drum sounds. BB—> Singular Sound Midi Cable (splits from one on the BB to MIDI IN and MIDI OUT) —> Aeros Loop Studio MIDI IN. BB controls start/stop and sync of Aeros BB—> Footswitch Helix —> 1/4 inch Out —> Aeros L (mono) IN. This lets me play with Helix and Aeros without BB if I want. Aeros —> 1/4 inch Out L Mono —> PC Input 2 Helix Global Settings 1/4 (line), XLR (line) All can act independently or together in any combination. The powercab L6 cable helps because I have three inputs. Thanks for the help. I’ll keep following to read about your studio setup and your pedal board setup.

@DunedinDragon and @datacommando nice to meet you both. Thanks for your help for a poorly worded question. Thank you for the YouTube vid as well. I think I may have answered my own question, but I’ll first post my reply on the SimplySound forum as I posted there as well. My current setup is as follows. Guitar —> Guitar In (Helix) —> 1/4” out (helix) to Aeros L(mono) In BB—> Exp In (Helix) BB —> Footswitch BB —> MIDI OUT to Aeros Midi IN With the HeadRush I ran L&R out of Eros 1/4 Y cable to Input 2 of the HeadRush Helix XLR —> to Input 1 of the Headrush Helix 1/4 and XLR Global settings to Line Now with PowerCab: Link 6 cable from Helix AES/EBU Link 6 Cable Digital out —> PC112+ (L6 Link AES IN) Can I change things to active the following: Play Helix straight to PC using the Helix modeling Play BB with Helix no Aeros Play Helix (modeling) with Aeros and BB. Here I want to make loops that don’t include the BB drums in the loop. Ok after trial and error this evening I think the following works: I can do #1 with my current cable setup. I can also do #2 by leaving the power off to the Aeros Loop Studio. I had this idea that I wanted a chance to record/keep the loops without the drum sound recorded in them, but the midi cable starts and stops the Aeros anyway so if I try to shut off the drum it stops the loops. That is the whole idea of the midi cable. Sorry just learning. I’m going to try to turn down the volume or see if I can run Headphone out so I could hear the drums without hearing it in the mix. I did try a separate cable to the PC112 and it did work, but the midi still stops the looper. The only reason I was trying to figure this out is I’m going to do cable management and I’m using python pedal covers and once I cut it, it would be difficult to change if I wired incorrectly. 95% of the time I would want the drums in anyway. Again thanks for the help. I would love any thought you have.

1m Hi all. Obviously new here and I did search for this type of question, but I didn’t see this addressed specifically. I have a helix floor connected to a line 6 power cab with the L6 link cable (xlr cable). Currently I have my BeatBuddy (with footswitch) midi out to my Aeros Loop station. I would like the Aeros to receive signal with all modeling that was performed on the Helix without hearing the drums on the loops I make. I probably have the 1/4 cables hooked in the wrong order as I hear the drums on the the loop. I’m very new to this as I normally just have an amp/cab setup. New to BB, Aeros, and Helix so big learning curve. Thanks in advance for any help.