clausiii

and yes just like the tremolo, the blue status light is blinking in the correct tempo but not on bar/beat, there is nearly every time an offset...

Hi! I came across this problem too, getting MIDI beat clock from Pro Tools. MBC works perfectly fine with delays and modulation fx which can be synced with it, no problem at all. only tremolo fx don't work 100% right. They do sync to the incoming tempo but the effect is not on the bar/beat. it seems that it just snaps anytime to the incoming tempo but ignores bar/beat and so it´s a hit or miss if the tremolo is in time or shifted by 1/16th, 1/32th,...

Thanks for the suggestions and links! Will take a look!

Hi! i´m trying to have a tremolo synced to the tempo of an incoming MIDI beat clock from Pro Tools. MBC works perfectly fine with delays and modulation fx which can be synced with it, no problem at all. only tremolo fx don't work 100% right. They do sync to the incoming tempo but the effect is not on the bar/beat. it seems that it just snaps anytime to the incoming tempo but ignores bar/beat and so it´s a hit or miss if the tremolo is in time or shifted by 1/16th, 2/16th,... any solution for that? thanks

Thanks! This is a pity not to have Instant Hotkey Commands on preset load only...

Hi! I´m trying to send keyboard shortcuts with my HX Effects only when a preset loads. how can I avoid that it's also sending them with the first loaded snapshot when using it again? Thanks!

Hi! I´m trying to use key commands to control the Pro Tools cursor. There cursor should go to specific memory locations when I launch a HX Effects preset. what I need is a series of keystrokes. For example: marker #1 in Pro Tools is .1. (period, number, period) and all done on the numeric keypad. is this possible?

Hi! Is it possible to create a row of hotkeys on preset load? My goal is to set the Pro Tools cursor to the right marker location. for example if the song start is marker 25 I need this -> .25. (dot+2+5+dot) will this be possible? Thanks! Claus

does this work with HX Effects too? urgently needed here! "New MIDI message (Helix Floor/Rack/LT/HX Stomp XL): CC71 engages the MODE switch" Thanks Claus

Hi! So, like everyone else does every now and then, I changed my guitar setup. Again. my idea was that for me it is not necessary to use the first three cables in the signal chain of the 7CM for my stereo setup. I don't need any FX of the HX Effects before going into the amp. I only used it for splitting the mono guitar input to the two Sends to my two amps. I changed that to an analog splitter (Lehle) to avoid unnecessary A/D D/A conversion. So the HX Effects is only in the amps effect loops, I only use delays, reverbs, modulation there. I´m fine with that, but my problem is now that I have now no access to the tuner. Am I missing the menu where to let the tuner listen to the signal? Or should I connet the effects loop differently compared to the 7CM? Thank you! Claus

no, you cannot use third party plugins in the free version of Pro Tools.

adding a bypassed effect to an imported preset on snapshot 1 is active in all other snapshots

I updated correctly to 2.80.1 and now on all my presets I´m missing/losing the CC Toggle settings when using snapshots. When I load a preset the cc# I programmed on the switches are there but as soon as I switch on a snapshot, they're gone. what am I doing wrong? or is it a bug?

next problem: adding a bypassed effect to an imported preset on snapshot 1 is active in all other snapshots..

Hi! I updated correctly to 2.80.1 and now on all my presets I´m missing/losing the CC Toggle settings when using snapshots. When I load a preset the cc# I programmed on the switches are there but as soon as I switch on a snapshot, they're gone. what am I doing wrong? or is it a bug? Thank you!