Jump to content

Search the Community

Showing results for tags 'post amp block'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Community Support
    • Multi-Effects Units
    • Variax Instruments
    • Amplifiers
    • Computer Based Recording
    • Live Sound
    • Pedals/Controllers
    • Dream Rig - Line 6 Product Integration
  • General Discussion
    • Share your Settings
    • Line 6 Lounge

Categories

  • General FAQ
    • Operating System-specific Information
  • Tutorial Videos
  • Effects/Controllers
    • HELIX/HX
    • DL4 Stompbox Modeler
    • FBV Controllers (MKII / 3)
    • M5
  • Recording
    • Helix Native
    • Metallurgy
    • Echo Farm/Amp Farm
    • POD Farm / POD Studio / TonePort
    • Computer Audio Set Up and Troubleshooting
  • Amplifiers
    • Catalyst
    • Spider V
    • Powercab
    • Spider IV/Spider Online
    • Spider Jam
  • POD
    • POD Go
    • POD HD X
    • Pocket POD
  • Guitars
    • JTV / Shuriken / Variax Standard / Workbench HD
  • Relay/XD-V Digital Wireless
  • Legacy Products
    • POD
    • Amps
    • Mobile Products
    • Effects and Controllers
    • AMPLIFi Series
    • Live Sound
    • Digital Wireless
    • 1st Gen Variax Guitars / Bass / Workbench
    • Software
    • Dream Rig
    • POD Studio / Tone Port / GuitarPort

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Location


Interests


Registered Products

Found 1 result

  1. Hi all, I know there has been plenty written by us customers about having a schematic of the routing through the "dream rig" and I can somewhat understand why that is difficult for Line6 to do, because there is so much software configurability and DSP areas in the process, it is almost like asking how long is a piece of string... However, I am looking into DT25 for my GIG rig and I am currently confused about how/where "post amp block" effects sit within the signal chain, bearing in mind a specific configuration... (as below) HD POD config looks like... Pre Section - Split path section - mixer block - post section - outputs (generic pod setup) for this discussion lets say it is effectively a mono path, so lets not talk about "panning or stereo" and so on... just keeping it "simple".. in the pre section is FX1 in the Split path (path a) i have FX2 followed by an AMP block (amp configured as a Pre version of the amp) in post section i have FX3. if I then set the "Audio Configuration" for the DT25 to be LEFT... then from the documents I understand it gets fed the signal from the end of the POD chain into the real POWER AMP (with topology/class etc. as configured by the pre amp specifics)... (I also understand that if I set the Audio Configuration to AMP A... the signal would go straight after the amp block to the power amp, and miss out the POST section and MIXER completely...(and incidently any FX placed after the amp block...) MY REAL QUESTION... is it possible to use the DT25 as the pre amp modeller and real power amp AND get the same FX placement (without using the 4CM)? e.g. POD config FX1 - FX2 - blank amp block - FX3 audio path would have to be POD(FX1 - FX2) - > DT25 preamp -> POD (FX3) -> DT25 power amp - DT25 reverb... another side question is does the audio ever "go back to the POD from the DT25..." im guessing not, and if so my answer to my real question is... it's not possible... Interested in anyones thoughts.
×
×
  • Create New...