Please ensure Javascript is enabled for purposes of website accessibility Jump to content

Need advice on stacking overdrives


dannymurphys
 Share

Recommended Posts

Hello

I'm trying to build some gigging presets for my HX Stomp XL using AC30- or Fender-style amp models. Ideally, I'd like to create a full pedalboard-style setup, with two overdrive pedals in front of the amp and modulation, delay, reverb, etc. in the effects loop/after the amp.

My biggest challenge is getting the clean and driven tones to work well together. Sometimes I dial in a clean tone that I really like, but then I'm not happy with the overdriven tones, or vice versa.

How do you guys approach building your gigging presets? Which overdrive models do you prefer, and how do you typically set them up? I'm struggling to avoid tones that sound either too fizzy or too flubby, and I'd love to hear your tips, experiences, and recommended settings.

Thanks in advance!

Link to comment
Share on other sites

I usually use the Aristocrat, Voltage or Kinetic which are all capable of nice clean, crunch and lead sounds which can be switched using snapshots or controller assignments (for two channels). I rarely use the ODs.

 

But to answer the question about pedals:

I like the Teemah! the most for adding gain when I just want 'more' but not 'different'. I think following these steps should work for you:

 

  1. Set up a clean amp sound you like / want / need.
  2. Add a Teemah! in front.
  3. Assign it to a footswitch.
  4. Hit the strings hard with open volume pot, toggle between on and bypass and set Level so that levels match.
  5. Now do the same with BassCut for bass frequencies and TrebleCut for treble.
  6. Now listen to the mids (the honk): if it's ok you're done.
  7. If you want more mids add Level, and increase BassCut and TrebleCut a little.
  8. If you want less mids lower Level, and decrease BassCut and TrebleCut a little.
  9. If you adjust Gain or Clipping do (4), (5), (6) again.

 

Experiment with the Clipping parameter:

  • Up:
    • Provides asymmetrical clipping.
    • Delivers moderate saturation and a slight amount of compression.
    • Gives a wide, dynamic, and touch-sensitive feel. 
    • My favorite.
  • Center:
    • Provides symmetrical clipping.
    • Features light saturation, high headroom, and great note definition.
    • Sounds open, loud, and uncompressed.
  • Down:
    • Provides symmetrical clipping.
    • Delivers heavier saturation and lower headroom.
    • Yields a more rounded, compressed, and thicker distortion feel.

Choose according to your needs based on the clean sound. If the clean sound is stiff Up, or Down add compression. If the clean sound is sagging / compressing Center might be better.

 

When you're done with that add a second Teemah! in front and do the steps again. 

 

After this procedure you should have a pretty good  base line with three options of gain (no Teemah!, the Teemah! in front of the amp, booth stacked).

 

You can now try other ODs or distortions by adding them and A/Bing them against one of the Teemah!s.

 

If you struggle to find a good allrounder cab, try the 4x12 Greenback25, 57Dyn, 1.8, 3.00", 0 deg, 137 Hz, 5.2 kHz.

 

All of this is just my personal opinion based on my experience - things might look/sound different for you, of course.

 

 

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

×
×
  • Create New...