gbr13697
Members-
Posts
142 -
Joined
-
Last visited
-
Days Won
1
Everything posted by gbr13697
-
Hi DarrellM5 I'm struggling to see the logic in your suggestion above. As far as I understand it, an attenuator just reduces the power out of the power amp into the speakers. This is normally used so that you can really crank the amp creating the warm distortion you get power tubes are really cooking, without the associated speaker volume. Much like some amps have switches to attenuate output volume to several reduced levels e.g. 40w, 10w,5w.1w to reduce volume whilst still getting the tone of volumes at 10. This is a useful feature, and a power soak can be used if the amp doesn't have attenuation switches built in. However, I really can't see how it replaces the functions of an effects loop. Can you explain?
-
A technique that I use a lot with the 4 cable method is to have both a modelled amp and an FX Send/Return in the preset. I assign one footswitch to both turn on the amp and turn off the loop at the same time (or the opposite). With the modelled amp off and the loop on, I can use the Helix as an effects unit and select which effects are placed before and after the loop. This gives me my own guitar amp's natural pre-amp and EQ on both the amps channels, and all the effects on the Helix used as a conventional pedal board. If I press the assigned switch, the FX Loop is switched off, and the modelled amp is switched on. The signal now bypasses my guitar amp's pre-amp and EQ entirely, and goes directly to the power amp stage. It obviously isn't FRFR, but it is as close as I can get with my rig. The effects now interact with the modelled amp, either before or after. I tend to place the FX Loop and modelled amp adjacent to one another in the Helix signal chain, so that the pre and post effects act in the same way whether using the modelled amp or my guitar amp. You have to be aware that when the signal is taken directly to the guitar amp's power stage via the Return cable, you lose the volume control on the amp (and the pre-amp channels). All the volume control, and EQ, has to be handled on the the Helix, so you do need to be aware of levels. I am rather lucky in that the Master Volume on my Blackstar Artist actually operates on the power stage, so I do still have an overall volume control. This does not apply to most guitar amps, and I have to be a lot more careful with levels and volume matching when using my Egnater amp.
-
Thank you all for the replies. That's what I needed to know, but isn't easy to glean from the info/reviews etc. I like my amps, and I only use the emulated amps occasionally for special purposes. Otherwise I'm just looking for a stomp box with easily accessible "multi-effects" to a reasonable quality. The quality of most on the POD or the GT100 is reasonable with exceptions. It was just that the POD makes them very hard to use efficiently, and I didn't want to spend a lot of money to get better effects if the were just as hard to build into versatile patches.
-
I am thinking about getting a Helix. I have used a POD HD500X for a while now, having also used a Boss GT-100, and I have found the number of slots available for effects etc rather limiting. 8 slots seems fine at first, but comparison with the GT-100 shows that it is far less generous. On the GT-100 there are “built in†slots for Compression, Pedal, Overdrive, EQ, Foot Volume, 2 x Noise Gates, an additional amp, Send/Return, Chorus, Delay, Reverb. That’s 12 slots (all of which have choices of pedal/amp within type) plus FX1 and FX2 which can be assigned from a large selection of pedals. That’s 14 in all. Many of these are items are “bread and butter essentialsâ€, particularly when using just effects and no amps with the 4 cable method. On the GT100, all the essentials are there, with a few luxuries, and still space for the odd gimmick. With no amp in the POD HD500x, and using the 4 cable method, slots have to be used for EQ, volume, Send/Return, and Noise Reduction. Most people would struggle without Delay, Reverb, Compression, and Overdrive, and that’s all 8 slots gone. There are lots of other effects available on the POD, but the only real way of using them is by devoting a patch to each and dumping something else. Not a very convenient solution for a “stomp box pedalboardâ€. How does the Helix compare in practice?
-
Thank you again Hurghanico. I'm pleased it's not just me. As you say it is a nice amp model, but the lack of EQ means you have to use it with the right guitar. Funnily enough, it sounds great with a Strat and awful with a Les Paul! Given that you can't turn down the treble, I thought it would be the other way around. Line 6 do seem to have got a bit pedantic in the pursuit of accuracy with some of these models. The example they had to profile might have been faulty - I don't think it's really necessary to faithfully reproduce a Soldano with a faulty pot!
-
I have been building a number of patches combining my selection of most-used effects with each of the pre-amp models. The plan is to try go through them with my guitars to find the best sounding pre-amps for each guitar. When I got to the Soldano models I found the I was unable to adjust the Treble tone setting. The screen display shows the Treble knob turning, but it makes no difference at all to the sound. The Treble control seems to work fine on the other amp models, just not the Soldanos. I am using my POD HD500X into a Blackstar HT5R with the 4 cable method. The pre-amp model patches are going straight in to the power section of the amp via the effects return, so the amp EQ can't be affecting anything. Is anyone else getting this?
-
Thank you for the explanation Hurghanico. I can see the reasoning in there, provided that the adjustment really is in the output stage of the POD. However, I still don't think it is a good idea to put EQ in globally, where the less initiated user might be totally unaware of it. I would think that the advice you quote of turning down the bass and treble on the guitar amp at the end of the chain is by far the better option. You also have the option of EQ in the modeled amps. If the same uninitiated user is just using effects and no amps, it's just a tone sucker. Once you have taken tone out of a signal you can never put it back. Thanks for all your input to my queries. You have been a great help.
-
Hi Hughanico (again!). Why would there be a distinction with using amp models that would make the attenuation more appropriate? If you are using the POD as a stomp box with amp modelling into a normal guitar amp, most people would set the EQ on the real amp. If they were also using the amp models, they might also use the EQ in the amp models, particularly if they were creating patches for a number of different guitars. However, if the high and low parts of the guitar's natural characteristics have already been taken out in the Setup>Output settings, nothing you can do of the amp models or on the real amp will ever properly put them back. The user's perception will simply be that the POD has sucked all the tone out. Most new users will have accepted the manual's recommendation to set the output for Combo, Stack or whatever, and are unlikely to choose the transparent Studio/Direct option. They might also accept (or not even notice) the Low/High attenuation on the basis of thinking that Line6 probably know best. This default setting certainly has a detrimental effect on the sound of my guitars. I am struggling to see the reasoning behind tucking away such a major EQ adjustment in a global setting, and how it could be better for using amp models into a real amp.
-
Atomant - If you persevere with the POD HD500X I have found (with the help of others on the Forum, and particularly Hurghanico) that you can get your sound back to pretty much what your straight in guitar sounds like. In Setup Inputs set the Guitar Z to 3.5M In Setup Outputs adjust the Highs (and possibly Lows) much nearer to Flat as opposed to the Default -50 attenuation. In each preset adjust the both the Mixer Pans to 0 (i.e. middle as opposed to Left or Right) In each preset adjust both the Mixer Volumes to somewhere between +3.5 and +5 depending on you guitar output. It can also help to put a Noise Gate in as the first item in the POD signal chain, to avoid the risk of getting a low impedance item appearing as the first link. With the Blackstar you also have the option of using the Effects Loop. This gets complicated, and there are contributions on this Forum. I have tried putting my GT100 straight in the the Effects Return of the amp with good results, if you can live with just using the amp as a power amp and having all the controls on the POD. You can also use the 4 cable method to have some of the POD effects going straight in to the front end of the amp, and have others inserted into the effects loop. This can be done with the POD or GT100.
-
Hurghanico - as you say, that is interesting, and largely confirms what I have found by ear as opposed to accurate instrumentation. I have adopted the suggestions you brought to my attention, particularly the mixer panning/volumes, impedance setting, and putting in a Noise Gate as suggested by Tyler. This certainly brings the gain/volume into line. The other notable item I have found is Settings > Outputs > High where Line6 have put in a default substantial attenuation. After restoring this to Flat my Strat sounds like a Strat again! It seems strange that Line6 would have chosen such a tone changing setting by default. It is nice to have some adjustment available for particular guitars and rigs, but to have a default substantial attenuation for Highs and Lows is an odd starting point.
-
Thanks Hurghanico. I can't use the 4 cable method with the Bassbreaker 007 as it doesn't have an effects loop. I can try it on my Blackstar HT5. I am already experimenting with the Mixer volumes and pan, and impedance settings. I will get there eventually. I'm pleased that I'm not the only one seeing signal loss and tone suck through the POD, and that there are solutions. I was thinking I had a faulty unit, given the assurance in the manual that turning volume and master up to 100% should give signal parity. Even without adjustments there can benefits such as the increased clean headroom on the Bassbreaker.
-
Thanks for the replies guys. On comparing results on other amps, including my Blackstar HT5R, I now realise that there is a significant signal loss through the POD. I get more volume, gain, and frequency response, with the guitar straight into any of the amps. With no effects or amps on the POD chain, I have to increase the Mixer volumes by 6-8db to achieve the same volume and gain and, even then, there is noticeable tone suck. I think I have found and adjusted the "usual culprits" listed by Guru. You can obviously get acceptable volume, gain, and tone, by inserting boost, EQ, and amps into the POD signal chain, but I think the natural characteristics of different guitars will inevitably get lost. I have some nice guitars, so that is a little disappointing. However, I have now been reminded of the obvious - that putting anything in the signal chain will change the sound, and almost nothing is really transparent. I will just work on getting some new and different sounds from the POD, and use other effects or amps for other sounds. At least this has prompted me to just plug my guitars straight into the amp occasionally!
-
Hi Atomant - it is reassuring to find someone else experiencing similar issues. I just bought a PODHD500X, and I was initially quite pleased with what I perceived as a vast increase in the clean headroom on my Bassbreaker 007. On comparing results on other amps, including my Blackstar HT5R, I now realise that there is a significant signal loss through the POD. Like you, I got significantly more volume, gain, and frequency response, with the guitar straight into any of the amps. With no effects or amps on the POD chain, I have to increase the Mixer volumes by 6-8db to achieve the same volume and gain and, even then, there is noticeable tone suck. You can obviously get acceptable volume, gain, and tone, by inserting boost, EQ, and amps into the POD signal chain, but I think the natural characteristics of different guitars will inevitably get lost. I also have a GT100 and ME-80 and I agree that they appear much more transparent. In fact they have a tendency to boost rather than loss, even when you don't intend it. You will know that the clean channel on the Blackstar HT5 is very clean, and the Dirt channel is very dirty (unless you are a metal head!). The GT100 will normally make the Dirt channel unusable for anyone that just wants a modicum of dirt. I found that the solution was to reduce the GT100 guitar input level by 10db in Global settings, and then adjust the volume on the Clean channel and Gain/Volume on the Dirt channel to taste. Messing around with these 3 parameters can achieve pretty much anything when using the GT100 on the HT5. Unfortunately it doesn't work so well on the Bassbreaker as there is only 1 channel - to get clean headroom you have to turn the levels on the GT100 and the Gain on the amp right down, which results in very little volume even with the volume on the amp right up. As various contributors to your thread have commented, nothing is perfect and it's all a matter of getting the best compromises possible for the result you want with the gear you have.
-
It does seem to be a little less than parity, even with everything turned up (but with no amp or effects in the POD signal chain). It is possible that I haven't worked out the mixer yet. It is a little difficult to tell, as the guitar straight in is quite sufficient to push the amp into distortion with gain at only 2-3. Putting the POD in the chain seems to clean up the sound through the amp, at the same or even much higher gain settings. This isn't a problem, as I am pleased to get the extra clean headroom. I just can't work out how the POD is preventing the Bassbreaker amp from distorting at high gain settings. I am used to the GT100 which tends to boost the signal, even when not intended. I had to turn down the guitar input to the GT100 by 10db (i.e. quite a bit less than parity), and keep the amp gain under 2-3 to prevent the sound breaking up with valve distortion. Any boost to the signal was instant dirt. I don't understand how I can put a (nearly) parity signal in from the POD, and turn the amp gain up to 8-9 without getting the amp's natural valve distortion. As I said, it's not a problem. I just can't work out how it's happening!
-
I have just bought a POD HD500X, and I'm using it into a Fender Bassbreaker 007 and 1x12 speaker cab. One of my problems with this amp was the very low clean headroom. I was getting valve breakup distortion with gain on 2 with any reasonable pickup output. With the gain this low, cleans were pretty quiet even with the volume full up. I previously used a Boss GT100, and had to reduce the input level in settings to avoid getting dirt straight in. The POD HD500X seems to over-ride the amp in some way. The output from the POD seems a little less than parity, in that the guitar straight in apparently gives a bit more gain and volume than the via the POD. However, when going through the POD I can turn the gain and volume on the amp up to 10 without any appreciable valve breakup. This does mean that I have to create the dirt in the POD, but it does give me a huge increase in the volume of clean sound. I can't see how the POD is cleaning up the sound and apparently stopping the amp from going distorted even at very high gain and volume settings. If I put the guitar straight in on these settings, it is just wall to wall distortion. Can anyone explain how this is happening?