Community: Message List

Re: DT25 - Does anyone else find the speaker very directional?

support@line6.com — Fri, 01 Mar 2013 22:48:23 GMT

So, if I have the DT25 1x12 combo, should I be getting the Weber 4" or 5" dome? Thanks, guys!

Wes

Re: Where are Deep Edit Parameters for amp sim in HD500 unit?

support@line6.com — Thu, 24 Jan 2013 15:31:55 GMT

Thank you, sir! Ya know, I got so busy looking at whether I had a cab selected (I use my HD500 with my DT25 combo and always run pre models) that I didn't even realize that running PRE's wouldn't call for deep editing paramaters. Thanks for the info!

Wes

Where are Deep Edit Parameters for amp sim in HD500 unit?

support@line6.com — Thu, 24 Jan 2013 12:48:07 GMT

Hey, guys! Probably a stupid question, but I can see the Deep Edit Paramters for cabinets in my HD500, but don't see the DEP for the amp sim itself. Am I blind? Thanks!

Wes

Re: Volume settings for DT25 + HD500?

support@line6.com — Tue, 22 May 2012 01:29:13 GMT

I have the HD500 and DT25 combo. I play at church with the amp fairly close to me, angled up on a stand. I run my DT25's Master Volum between 2-3 o'clock and set my patches volume with either the HD's volume control or straight from the DT25. Once I get that dialed in with the full band playing, I save the patch so that I can always cut back on the DT25's Master Volume or raise it a little if needed.

Wes

Re: Nick_Mattocks...Gone but not forgotten

support@line6.com — Sat, 12 May 2012 01:51:10 GMT

So sorry to hear this. He contributed a ton to these forums. RIP, Nick.

Re: not receiving line6 email

support@line6.com — Tue, 01 May 2012 12:43:16 GMT

I have this same issue with my Comcast email account. I never get any type of email notifications to threads I've subscribed to, but get them from every other guitar forum that I'm a member of. Wouldn't think Comcast would be an issue.

Wes

Re: DT25 was the right choice!

support@line6.com — Fri, 20 Apr 2012 00:20:53 GMT

Just got my DT25 combo recently and have been using an HD500 for quite a while by itself. Excited to get this thing dialed in!

Wes

Re: DT25 Line Out not working in standby mode?

support@line6.com — Fri, 20 Apr 2012 00:17:47 GMT

Greg,

Thanks! I, too, pan both mixer sliders in the HD to center. Looking forward to spending time with the combo and HD this Saturday. I left my main guitar at church with my DT25 and HD500. I assumed that if I wanted to use the 4 voicing in the DT25 that I'd simply go to the patch in my HD500 and simply turn off the amp block. Then I could just use the HD for drive pedals, compressors and effects. I'm guessing I can't do that based on your response. I don't have a lot of experience with the 4 cable method, so please excuse my ignorance:)

Wes

Re: sharing hd500/dt25 patches

support@line6.com — Fri, 20 Apr 2012 00:12:08 GMT

Thanks, Brent! I'll give these a go this Saturday when I can get to my DT25 combo (at church).

Wes

Re: DT25 Line Out not working in standby mode?

support@line6.com — Mon, 16 Apr 2012 12:47:09 GMT

Greg,

Thanks for your reply. That makes sense:) The good news is that, although I need to get patches dialed in more, I got to use the DT25/HD500 for the first time yesterday at church. I won't be using LVM, even though I stand close to my amp.

I was just thinking last night about running the amp's Master Volume higher and lowering the patch volumes in the HD to do just what you were saying. Yesterday, my patches were set up with good levels. My amp's Master Volume was at about 1-2 o'clock.

Let me know if you have a set list that is working well for you. I struggle with putting together good tones, as I get overwhelmed. I had thought about keeping it really simply and using the DT25's 4 voicings and HD only for effects, but realized that would limit the potential of both units:) Thanks!

Wes