Community: Message List

Re: problem with dl4 looper

support@line6.com — Fri, 08 Jun 2012 01:02:23 GMT

If you still have questions, please know that Line 6 is no longer supplying support via the forums. Instead, you can create a direct support ticket at:

http://line6.com/support/

Re: Recreating Adam jones with an HD500 - will x3 settings work on an hd500?

support@line6.com — Fri, 08 Jun 2012 01:00:14 GMT

POD X3 Tones are not directly compatible with the POD HD500. However you could use POD X3 tones as a reference point to start with on the POD HD500, as long as the same amp model is used between the two.

If you are looking for tones I would suggest that you check out our CustomTone website for all our user created and uploaded tones available at:

http://line6.com/customtone/

In addition you can post a request for this tone in our "Share your Settings" forum at the link below:

http://line6.com/support/community/general_discussion/share_settings

Another thing to keep in mind when trying to create your own tones:

If you want to create an artist-inspired tone “from scratch,” start by researching the guitar setup you are trying to emulate. Web sites, such as guitargeek.com and uberproaudio.com, list the rigs of many well-known guitarists. Guitar and recording magazines often print accurate diagrams and layouts (sometimes with the actual microphones used and distance from the cabinet).

Finding the following information will help you create an artist tone from scratch:

Amplifier, speaker and cabinet. Generally speaking, open-back guitar cabinets (such as a 2x12 cabinet found on many Fender® and Vox® amplifiers) will have less low-end response than a closed-back cabinet (such as a 4x12 closed-back cabinet used with many Marshall® and Mesa/Boogie® amplifiers)

Guitar (make/model) and pickup type. Alder or Ash bodies (commonly found on many Fender® guitars) sound different than mahogany bodies with maple tops (commonly found on many Gibson® guitars). Single-coil pickups (often used for bright/clean tones) sound different than humbuckers (which sound darker than single-coil pickups but not as noisy when used for higher gain tones)

Pedals, effects and signal-chain placement. Effects can drastically change a guitar tone so you should know what effects were used and where they were placed (between the instrument and amplifier, or after the amplifier).

Microphone type and placement. If possible, find out the kind of microphone used to record the tone and its angle and distance from the speaker. All of these play a significant role in changing the sound.

Re: when i turn my pod 2.0 on and hold TAP i see some stuff i dont recognise: it says TST and after that i get T0P. with my arrows it goes up to T1P,T2,T3,T4...up to T8 what is this parameter?

support@line6.com — Fri, 08 Jun 2012 00:53:52 GMT

This is a test mode for repair techs to test the POD 2.0.

This should not adjust the way your POD 2.0 sounds when booted up normally.

If you still have questions, please know that Line 6 is no longer supplying support via the forums. Instead, you can create a direct support ticket at:

http://line6.com/support/

Re: Correct signal chain with M9

support@line6.com — Fri, 08 Jun 2012 00:46:15 GMT

Since this question requires an opinion-based answer, we will mark this question answered. Feel free to post again to continue the conversation with other community members, but without marking it as a question. Marking the post as a question will lead it right back to Line 6 Support.

If you still have questions, please know that Line 6 is no longer supplying support via the forums. Instead, you can create a direct support ticket at:

http://line6.com/support/

Re: HD500/Blackstar AMP 4CM Hiss

support@line6.com — Fri, 08 Jun 2012 00:42:13 GMT

If you still have questions, please know that Line 6 is no longer supplying support via the forums. Instead, you can create a direct support ticket at:

http://line6.com/support/

Re: update with monkey

support@line6.com — Fri, 08 Jun 2012 00:40:19 GMT

If you still have questions, please know that Line 6 is no longer supplying support via the forums. Instead, you can create a direct support ticket at:

http://line6.com/support/

Re: X3 Live into HD500

support@line6.com — Fri, 08 Jun 2012 00:39:36 GMT

If you still have questions, please know that Line 6 is no longer supplying support via the forums. Instead, you can create a direct support ticket at:

http://line6.com/support/

Re: Monkey 1.53 for Mac locking up after update

support@line6.com — Fri, 08 Jun 2012 00:38:38 GMT

We have recently released an update to Monkey 1.56 on MAC OSX, it can be downloaded directly from the link below:

http://line6.com/getrelease?rid=5002

I have provided a link to more information about the Spider Infusion FX 2.0 update below:

http://line6.com/support/docs/DOC-2049

If you still have questions, please know that Line 6 is no longer supplying support via the forums. Instead, you can create a direct support ticket at:

http://line6.com/support/

Re: Slash sound with POD FARM 2.5 POD UX1?

support@line6.com — Fri, 08 Jun 2012 00:34:33 GMT

If you are looking for tones I would suggest that you check out our CustomTone website for all our user created and uploaded tones available at:

http://line6.com/customtone/

In addition you can post a request for this tone in our "Share your Settings" forum at the link below:

http://line6.com/support/community/general_discussion/share_settings

Another thing to keep in mind when trying to create your own tones:

Finding the following information will help you create an artist tone from scratch:

Re: Disabling the L6 Link while leaving outputs active

support@line6.com — Fri, 08 Jun 2012 00:29:23 GMT

You can not disable the L6 Link signal feed to the DT-50 from the HD Pro without phyiscally disconnecting the XLR cable or powering off the DT-50.