Community: Message List

Re: Vysex and USB To MIDI Cable Issue

support@line6.com — Mon, 18 Mar 2013 13:09:59 GMT

any help yet?

Re: wah / volume calibration on floor pod plus

support@line6.com — Thu, 03 May 2012 22:15:51 GMT

the calibration was not done correctly. this is what you should look for: the lights should progressively get from 0 to 100 slowly as you push down to your toe.

Check the manual again and make sure you do exactly as stated there!

good luck!

Re: Floor Pod Plus Wah Pedal Calibration

support@line6.com — Thu, 03 May 2012 22:06:47 GMT

Hi there! Honestly the calibration should be done just like a joystick. The 0 and 100 position right on target

What you can do to regulate the wah the way you want it is connecting your Floor Pod Plus to the pc with the vysex software and mess with the wah setting there because you'll find it to be the best way to go around it.

If you try and calibrate the pedal just thinking of it as a wah you might end up with the volume pedal setting not working so hot.

Re: FloorPod Plus Volume/Wah Calibration... HELP!

support@line6.com — Thu, 03 May 2012 21:50:53 GMT

I don't know if this will go in time but here I go:

so you want the volume range to be 50-100 instead of 0-100 is that it?

Well I think you can accomplish this because from my understanding, what the A B and C buttons do during calibration is tell via software the position of the expression pedal.

i.e: when you put the pedal in the toe position and press A (or B i don't remember right now) it sends the information that the pedal is in the maximum toe position.

you might be able to play around with this and "fool" the pedalboard.

another way you could accomplish other depth and volume on the expression pedal is change those settings on the Vysex software. This way it won't mess with the calibration of the pedal itself and it won't mess with your wah (if you use it)

hope this helps

Re: Hardshell case for Floor pod plus

support@line6.com — Thu, 03 May 2012 21:44:43 GMT

I've been using a gym bag to carry it around I am affraid that won't help you much. but you might find some "good" hardshell cases on amazon or something like that.

maybe chinese made ones? they are usually more affordable

Re: problem with my floor pod plus

support@line6.com — Mon, 16 Apr 2012 10:07:59 GMT

the factory reset was supposed to clear everything up and allow you to reprogram it but it seems you have a hardware issue in the pedalboard itself. take it to where you got it or a local music store and see if they can fix it or exchange it for a new one.

Vysex and USB To MIDI Cable Issue

support@line6.com — Thu, 12 Apr 2012 23:24:51 GMT

Hello there Line 6 experts.

I have a Floor Pod Plus that I love and got some great sounds on it.

Up until recently a friend of mine lent me a UA-4FX audio interface with MIDI ports with which i was able to edit effects and store them into my pod and so on.

Recently I was given an USB to MIDI cable but it's not working properly

I have tried installing,unninstalling, and I am not going anywhere close.

At this moment the cable seems to be detected by the Vysex software, but it's not sending data or receiving.

It receives minor commands like, if I press channel A on the pedal, the software detects it and shows up on the pc, but I can't neither save,load or do any other operation.

If I try a sync command the program doesn't send or receive any data.

The cable seems to be working correctly and the POD does in fact sync with the other interface so I am guessing this is a software side issue.

Any help would be greatly appreciated by me and my friend whom will get his USB audio interface back

Re: (112770) PETRUCCI by

support@line6.com — Thu, 22 Mar 2012 10:44:21 GMT

Can anyone make a Pod Plus compatible sound of this? or give me the settings manually to see if I can recreate this a bit

Re: problem with my floor pod plus

support@line6.com — Thu, 22 Mar 2012 09:52:04 GMT

have you tried doing a factory reset?

While plugging it in hold the Channel Up and Channel Down footswitches and see if that helps.

Re: Floor Pod Plus Muddy sound

support@line6.com — Thu, 22 Mar 2012 09:30:50 GMT

last night I managed to get some sweet rythm distortion sounds of it. My clean settings and solo settings all sounded great but what was happening was that I had little to no presence on some presets, and the the clean channel of the amp I was using, was causing some issues to but I think I managed to fix it because now everything sounds right to my ears.

What are you connecting your Floor POD+ to?

Settings for the POD:

If you are using an amp just like I do, make sure the POD is set to the kind of amp that you have (open back, closed back, whatever it is)

check if you have the switch on the back set to the AMP position and regulate the output level properly (if 0 is muted and 10 is full blast, get it up to 7-8)

On the Amp:

make sure that you are using the most clean setting of the amp you have. You might have to plug the guitar directly to the amp and try and mix the bass,mids and treble to the right ammount so that everything sounds as even as possible. Also, remove all the reverb from your amp and get the channel volume a bit higher than 12 o'clock

I strongly advise that you get a MIDI to USB cable and use Vysex to regulate your settings. Helps a lot to really tweak the POD to your needs.

If nothing of this solves it, go to a Line 6 service point and see if they can help you out