Community: Message List

Re: Wifi Problem iPad 4

support@line6.com — Thu, 18 Apr 2013 22:49:33 GMT

Instructions for how to update your StageScape M20d can be found at the following web address: http://line6.com/support/docs/DOC-2832

Also, be sure to try different wifi channels on the StageScape, make sure you have a direct line of sight between your StageScape and your iPad. Also, be sure that you do not have competing wifi routers within close proximity to your StageScape.

Re: Warranty Period?

support@line6.com — Wed, 27 Mar 2013 17:25:00 GMT

Hello,

We do have a support document stating warranty information. Your warranty is upheld in the region where it is purchased.

http://line6.com/support/docs/DOC-4838

Re: recording meter in future upgrades?

support@line6.com — Wed, 27 Mar 2013 17:17:54 GMT

Hello,

Thank you for your input and I will forward this request to my manager. However, please also psot this request in our product feedback section, which can be found at the web address below:

http://line6.com/company/contact/productfeedback/

Thank you and I hope this is helpful.

Re: Handheld dead after error in firmware update - what should i do now???

support@line6.com — Fri, 22 Mar 2013 19:22:54 GMT

Hello,

Your ticket was not deleted. I transfered your ticket to our UK support team since you are in Austria. I apologize that it may have taken longer than expected for a reply, but we definitely did not forget about you or delete your support ticket.

It will be best for you to register your transmitter to your account, as well as complete the address information on your account, and upload a copy of your receipt in order to expedite service from our UK support team.

Thank you for your patience and I am sorry for the confusion.

Jon

Re: Got the Dreamstage - How to integrate the POD HD500 via Line6 Link?

support@line6.com — Wed, 13 Mar 2013 15:57:15 GMT

You are correct that there is no L6 Link input on the HD500. You can connect a HD500 via L6 Link to a L2/L3m/t which will default the speaker to the Electric Guitar mode. This speaker is effectively a full range flat response guitar amp at that point, however the best way to integrate the HD500 into your full system would be to take the analog outputs from the HD500 into the analog inputs of the M20d.

Re: Wish: linking two M20d

support@line6.com — Wed, 13 Mar 2013 15:43:29 GMT

Please feel free to voice this suggestion in our product feedback section. This section is reviewed by managers and is the best place to voice requests of this nature. Our product feedback section is at the link below:

http://line6.com/company/contact/productfeedback/

Re: L6 link and aux outs...

support@line6.com — Wed, 13 Mar 2013 15:37:52 GMT

Hello,

You can assign multiple speakers to the same monitor when L6 linked. In terms of a maximum number of monitors, I have not really seen one yet. The most I have used is 4, but, again, you can assign multiple speakers to the same monitor send when using L6 Link.

When sending audio to monitors via L6 Link you can also use the analog monitor sends - both outputs will work at the same time. If you are using the analog monitor sends, you can take the line out from monitor 1 and continue it along to monitor 2, 3, ... etc.

Re: L3s Overheating

support@line6.com — Mon, 04 Mar 2013 23:18:26 GMT

Hello,

Also, if the LED on the front of your StageSource speaker turns red, that is informing you that the internal tempurature is reaching near overheating levels. If the LED doesn't turn red, you should not have to worry about overheating.

Re: Android?

support@line6.com — Thu, 28 Feb 2013 00:05:58 GMT

At this time, only iPad devices are supported for remote control of the StageScape. As to whether or not this can be something in a future firmware, I cannot say either way. However, the more users request features like this, the more it increases the chances of those features being seen in the future. Feature requests can be done at the web address below:

http://line6.com/company/contact/productfeedback/

Re: StageSource Stereo Pair Config Options

support@line6.com — Wed, 27 Feb 2013 23:53:08 GMT

A L3t and L3m (or L2t and L2m) L6 Linked together is supported by Line 6. I would consider it normal and not "hackish" at all. You can also L6 Link a L3t to a L2t or L2m, but, if being used as mains, a L3t and L2 would be an asymetrical system... which could be considered slightly hackish. But the speakers are quite stylish.