Community: Message List

Re: Fx-loop - Bug or feature?

support@line6.com — Mon, 01 Oct 2012 21:06:02 GMT

It doesn't matter what mode it is in.

Unfortunetly the reverb is pre fx-send as well. It makes the delays sound washed at times...

Fx-loop - Bug or feature?

support@line6.com — Mon, 01 Oct 2012 08:43:37 GMT

I've just realized that the fx-send is post master volume.

Using rack compressors or other level triggered fx won't work properly in this situation. I would like it to be pre master volume, but post channel volume.

Is this to be considered a bug or feature?

Re: Why did Line 6 stop producing the Vetta amps?

support@line6.com — Mon, 17 Sep 2012 16:16:35 GMT

When looking inside the dt-amps, the pcb's are labeled vetta :-))

Dt50 and x3?

support@line6.com — Mon, 17 Sep 2012 15:26:27 GMT

http://line6.com/support/thread/87729

Re: x3 live and dt50?

support@line6.com — Mon, 17 Sep 2012 15:24:08 GMT

No one used this combonation?!

I'll post in the amp forum instead.....

x2 and v70

support@line6.com — Thu, 13 Sep 2012 13:16:25 GMT

Aside from the antenna missmatch giving you a reduced range of operation, would there be any other implications attaching the x2 to the end of the v70 antenna chain in my rack?

Dt50 midi

support@line6.com — Thu, 13 Sep 2012 06:36:49 GMT

Is there a way from midi to read the current settings?

If I set i.e. the volume control to 50% in midi but the actual position is 100%, will the volume jump when I touch the volume control?

When l6link is used the internal preamp can be disabled. Is it possible to disable the preamp via midi if I go analog?

x3 live and dt50?

support@line6.com — Tue, 11 Sep 2012 07:20:01 GMT

I'm not so frequent here anymore it seems...

I just got myself a nice dt50 and I have yet to convert and buy an HDx00.

So I searched and googled, but to no avail, trying to find some killer patches and setup tips/tricks.

Forumwise it looks like no one have used this combo .

Today, at rehersal, I'll try the dt50 as a keyboard amp for my korg kronos

So.... Point me into the right direction.

Re: Upgrading Relay 90

support@line6.com — Fri, 20 Jul 2012 07:46:06 GMT

dboomer wrote:

User flashing using Monkey requires that the proper firmware in present in the transmitters. Getting it up to that level will require returning it to us. That said your current transmitter will work correctly with any other Line 6 receiver that is running in RF1 mode.

Yes, this is my understanding too. For logistic reasons it is difficult to run this bodypack in rf1 since it may ruin other xd-v-devices that I have no control over...

Now, what is the proper procedure to return my device to line6? I assume I can send it to UK?

Re: Upgrading Relay 90

support@line6.com — Thu, 19 Jul 2012 08:24:14 GMT

dboomer wrote:

Same answer ... except you do not connect to a G90. You just lay the transmitter on the antenna (b-out) of the V75. All the instructions are contained in Monkey. There are also videos and instructions in the documents section of the XD-V page.

Now you confuse me or you didn't understand me fully...

According to the post above

holding down select just causes it to skip the startup info and go directly to the main screen. The select button itself obviously works, since it changes the behavior - it just doesn't provide the behavior I expect to see.

and your reply was

If that happens it is pre-1.02 and will need to be returned as the flash involves special hardware. Please contact the service department to arrange for it.

According to that statement the option to use the xd-v75 for upgrade is not doable. To be certain I'm not missed anything I've double-double checked and I can't enter boot mode in any documented way on this transmitter...

As I've said above I have this old/non-upgradable firmware (that won't enter boot loader). This firmware is obviously pre-1.02.

According to my service center they don't have that type of special hardware and I'm out of warranty so I can't force them to upgrade/replace my tbp12. This is also why I was asking about the intel-hex file since I could do the flashing myself with my ISP/JTAG programmers.

Now, what shall I do or do I have to bin the transmitter, since the rest of my systems (v70/v75) are upgraded and already using rf2-mode?!