Community: Message List

Re: AX 212 Volume Problem

support@line6.com — Fri, 04 Jan 2013 20:04:44 GMT

First warning signs of a crash. Immediately back up your amp settings on a computer with midi - then do a hard reset of the amp. Then reload your presets via midi and test the amp again. Keep it on for several hours and try it over and over to try and duplicate the issue. If it persists - you need service. In not - you got lucky. I always bring a backup rig just in case when I use the Ax2 live.

Re: Have an AX2 with Floorboard I would like to move

support@line6.com — Tue, 23 Oct 2012 05:43:36 GMT

If it's still for sale email me at dm@pottymouthproductions.com and I'll take it

thanks!

Re: blitte

support@line6.com — Sun, 02 Sep 2012 15:58:01 GMT

First try a hard reset. You lose all of you presets - but this is the first thing you should always try when these amps go screwy. And you should be bakcing your stuff up using midi anyway. If that doesn't work - then It needs to be serviced. Take to a Line 6 service center. I had one do this that was unrepairable according to the service center. They didn't charge me and they pretty much tried everything. I have it in my garage fo parts in case my other AX212 goes bad. Good Luck.

M9 vs. Strymon Timeline Tape Delay Comparison Video

support@line6.com — Mon, 30 Jul 2012 02:56:18 GMT

I made this video - it is very long an boring - but if you were wondering if the M9 can keep up with the Strymon Timeline's Tape delay - well here is your answer. Enjoy!

M9 Audio Level Drop when using Mod effects...

support@line6.com — Mon, 30 Jul 2012 02:53:57 GMT

So I have the latest firmware and generally I think the M9 sounds great - using it in the effects loop of my amp for mostly delays, reverbs and some mod effects. BUT - there are certain effects that decrease my volume even when the mix knob is all the way up. In particular the Leslie effects, tremolos and some of the weirder Tron and synthy stuff. Almost every one of them gives me a volume decrease when engaged. This does not happen with the chorus, delays, or even the phasers/flangers. Any ideas here on how to keep my volume level consistent? I have 2 different amps that I use and this issue is persistent on each of them. is it an order thing? Usually I set the delays and verbs last in the chain - with the modulated stuff before them.

Re: expression pedals

support@line6.com — Mon, 02 Aug 2010 09:27:46 GMT

I am selling my Mission EP1-L6 pedal in Red. If anyone is interested I can send pics via email. Mint condition - in original box. $90 shipped/ paypalled.

Re: How to improve overdrive/distortion tones

support@line6.com — Sat, 12 Jun 2010 08:14:37 GMT

I think the overdrives and distortions are pretty weak, thin sounding and just plain harsh and not musical in the M13 compared to the real thing. I have a lot of the actual overdrives and comp pedals modeled and there is really no comparison. They seem to really thin out the guitar tone where the original pedal will not and have this very digital frequency that I can't dial out. My solution has been to bypass them (comps/overdrives/distortions) entirely and use the real pedals I like in front of the M13 and then have the verbs and delays and other fun stuff go through my amps effects loop using 4CM. The M13's biggest problem IMHO is the crappy sounding drive section. They could really improve it.

Re: Using the M13 to control my JVM's channels using midi is AWESOME!!

support@line6.com — Thu, 27 May 2010 17:22:24 GMT

Pedalsnake. http://www.pedalsnake.com/

Show off your M13/M9 pedalboard

support@line6.com — Mon, 01 Mar 2010 19:04:35 GMT

I'd like to see what some people are doing on the floor as I am setting up a new pedalboard using my M13 a Mission controller and some pedals in the loop. I find most pedalboards too deep. Right now my ideal board is 28" x 13" and it seems that no one makes that. So show off what you got going on.

Re: MISSION EXP Pedal Shoutout

support@line6.com — Sat, 05 Dec 2009 22:14:14 GMT

Here is the direct link. I bought a red one.

http://www.mission-engineering.com/Mission-Engineering/Mission_Engineering.html