Community: Message List - My POD HD Pro won't start

Re: My POD HD Pro won't start

support@line6.com — Wed, 19 Sep 2012 05:52:39 GMT

It was actually 2.02! That's what I meant by "the latest version", so actually rolling back (the only option) brought me back (to the future) which was/is 2.02! Now I know what Michael J. Fox must've felt like...

cgtrox

Re: My POD HD Pro won't start

support@line6.com — Wed, 19 Sep 2012 03:09:55 GMT

Just curious - if you rolled back to the latest version of the software as you stated being 2.02, what version were you running that caused your similar problems that the original poster wrote about having?

No new POD HD500 or PRO software has been released yet and we're all still waiting, so I'm curious what you were running that you rolled back to 2.02?

Thanks.

Re: My POD HD Pro won't start

support@line6.com — Wed, 19 Sep 2012 00:30:24 GMT

Man, that sucks bro! I too just recieved mine about a week ago and it was fine for the first few times. I plugged it into the computer and tried to check the version on Monkey and it said it didn't recognize the HD Pro. So, I hooked up my POD HD bean and it saw that, but still no Pro. So, I tried the "power up holding the button" (all 4 ways) system a few times and I got it to go into the FLASH UPDATE... screen and then got stuck! Nothing worked! So, I went to the Monkey and rolled it back to the 2.02 version (which is the latest btw) and it worked! I hope this works for you, even try rolling back further if you can, good luck man...

cgtrox

Re: My POD HD Pro won't start

support@line6.com — Tue, 18 Sep 2012 21:51:24 GMT

i would start from scratch if you haven't already done so. remove all line6 stuff and start over. try a different computer/cable. if it happened to two new pods, it has to be something with your set-up

Re: My POD HD Pro won't start

support@line6.com — Tue, 18 Sep 2012 21:11:15 GMT

So, is there another way to fix this probem?? I now have the new one and it did it again! I'm trying all the advices here and nothing works. Not cool to be replacing this thing over and over.

Re: My POD HD Pro won't start

support@line6.com — Sun, 12 Aug 2012 17:20:28 GMT

Thx a lot my friend i had the same problem and now everything works just fine

Re: My POD HD Pro won't start

support@line6.com — Mon, 06 Aug 2012 22:58:07 GMT

ok, so it appeared to work.... this time starting up with the right button worked and i re-installed the 'firmware' with the monkey, and now it will turn on and reach the normal view but it won't give any output and turns off and back on again after a bit less than a minute and repeats the cycle

Re: My POD HD Pro won't start

support@line6.com — Mon, 06 Aug 2012 22:21:18 GMT

i just had this problem ten mins ago with a HD desktop. holding the down button whilst powering up came up with some 'flash update' screen, and it was detected by the monkey but nothing changed. holding right key did absolutely nothing, then holding left key it started as it had when i got it this morning! think it was some issue with not all the drivers etc being up to date. hope this helps anyone

^^ false hope see my own reply

Re: My POD HD Pro won't start

support@line6.com — Sun, 05 Aug 2012 22:37:07 GMT

Try starting it up while holding down the left nav key.

Re: My POD HD Pro won't start

support@line6.com — Sun, 05 Aug 2012 18:17:06 GMT

Is there any fix to this problem? I have had this unit for 2 weeks and am recording an EP (mindfuck?).

It just won't start, tried both silverhead and jimsreynolds advice.