Community: Message List - Question about pod hd500 with analog pedals!!!

Re: Question about pod hd500 with analog pedals!!!

support@line6.com — Sat, 08 Dec 2012 18:23:56 GMT

I've only used overdrive/distortion pedals in front of it but they've worked pretty well.

The Boss Metalzone sounds exactly like the one built in the HD500 I have, but with a few more tone tweaking options. Other than that though, spot on.

So if you have pedals you want to use with the HD500 go for it.

Re: Question about pod hd500 with analog pedals!!!

support@line6.com — Sat, 08 Dec 2012 15:42:42 GMT

OK, esa era mi duda, te pasaste.

al cambiar mi configuración de entrar a un power y ahora conectarme a un cabezal a tubos los bajos son muy hermosos, el bass del bloody supera en mucho al bass que te entrega el HD.

saludos.

OK, that was my question, you spent.

to change my settings to get to power and connect to a head now to the low tubes are very beautiful, the bass of bloody far exceeds delivers bass you HD.

greetings.

Re: Question about pod hd500 with analog pedals!!!

support@line6.com — Sat, 08 Dec 2012 15:24:20 GMT

No se si entendi bien la pregunta...

Vos queres conectar el Bloody Mary con el pod y el amplificador con el metodo de los 4 cables?

La cadena podria ser asi:

1) Cable 1 Guitarra >>> HD in >>> Efectos del pod qe quieras antes del pre del ampli (distorsion, etc) >>> FXLoop(del pod) >>>

2)Cable 2 HD SEND (envío) >>> AMP Input

3 )Cable 3: AMP SEND >>> HD Return >>> Efectos que quieras despues del pre del amplificador (Delays, Reverbs, etc, los que configuras "por software").

4)Cable 4: HD Main Out (L o R) >>> AMP Return.

El Bloody Mary lo podes poner entre la guitarra y el pod, o entre el SEND del pod y el Input del AMP. Fijate como te gusta mas. Va a depender de que simulacion uses del pod. Tenes que ordenar las ganancias. Yo pondria de menor ganancia a mayor. O sea, si usas el Screamer del pod, el Bloody Mary lo pondría entre el SEND del Pod y el Input del AMP. Pero es cuestion de probar...

Espero que te sirva la respuesta, saludos!

Re: Question about pod hd500 with analog pedals!!!

support@line6.com — Sat, 08 Dec 2012 13:43:15 GMT

ok, gracias Fede17_dream, entonces el setting es:

1) cable 1 : de Input guitarra a IN del HD

2) cable 2: del SEN del HD al Input del Amplificador ( y equi configuro el FXLoop con un compresor por ejemplo y luego un overdrive ) y tambien podria colocar (SEN del HD al Input del Bloody Mary y del Ouput del Bloody al Imput del Amplificador)

3) Cable 3: Return del HD al SEN del Amplificador

4) Cable 4: del Out del HD a Return del Amplificador y el delay + reverb que configuro en el software se iria por aqui?

desde ya gracias.

ok, thanks Fede17_dream, then the setting is:

1) Cable 1: Input IN HD guitar

2) Cable 2: SEN of HD to Amplifier Input (and configure the equipment FXLoop with a compressor for example, and then an overdrive) and could also put (SEN of HD to the Bloddy Input Ouput of Mary and the Imput of Blody Amplifier)

3) Cable 3: Return of the SEN HD Amplifier

4) Cable 4: Out of the HD to Amplifier Return delay + reverb and configure the software that would go over here?

from already thank you.

Re: Question about pod hd500 with analog pedals!!!

support@line6.com — Sat, 08 Dec 2012 12:55:30 GMT

Hola! Las reverbs y delays tendrían que estar despues del bloque "FXLoop" del pod, para ubicarlos despues del pre del amplificador.

Saludos!

Re: Question about pod hd500 with analog pedals!!!

support@line6.com — Fri, 07 Dec 2012 12:02:57 GMT

Holas, estoy a las puertas de comprarme un amplificador Egnater Tourmaster , y quiero saber como es la configuración en utilizando el software, con el metodo de los 4 cables.

estoy claro que debo enviar las distorsiones al imput del amplificador, eso significa enviarlas desde el SEN del HD500, pero los reverb y delay como se mostrarian en el software?

Hellos, I'm on the verge of buying a Egnater Tourmaster amp, and I want to know what the configuration using the software, with the 4-wire method.

I am clear that I send the amplifier distortions imput, that means sent from the SEN of the HD500, but the reverb and delay as displayed in the software?

gracias por sus comentarios.

Re: Question about pod hd500 with analog pedals!!!

support@line6.com — Sun, 12 Aug 2012 18:54:00 GMT

seria muy bueno saber como los conectas, si lo haces antes del POD, despues del POD o en el interior del HD Edit.

desde ya gracias.

J.V.

would be nice to know how to plug them, if you do it before POD after POD or within the HD Edit.

from and through.

J.V.

Re: Question about pod hd500 with analog pedals!!!

support@line6.com — Mon, 06 Aug 2012 20:33:05 GMT

I use several different pedals in my setup and they sound fantastic with the POD. I have a Hotcake Overdrive, Eric Johnson Fuzz Face, Vox Satchurator, BBE Boosta and a Deja Uni-Vibe in conjunction with the POD.

In the past few months ( I admit I struggled to get the tones I had hoped for initially) I have had many people comment on my tone and say how awesome it sounds. Always a good thing. Didn't always get that with my last setup!

Re: Question about pod hd500 with analog pedals!!!

support@line6.com — Mon, 06 Aug 2012 12:33:28 GMT

The modelled amps respond the same way that the real amps would with the same pedal infront of them. It's really as simple as that. If you hit these amp models with a hotter input from a boost, they'll start to overdrive up just like the real amp would. If you put a distorted tone, modulated tone or wah'ed tone into them, they'll amplify that tone and react to it in the same way as the real amp that's being modelled. Line 6 have put an enormous amount of effort into the authenticity of their amp modelling and it shows when you do things like put pedals into the modelled effects chain.

Cheers,

Crusty

Re: Question about pod hd500 with analog pedals!!!

support@line6.com — Mon, 06 Aug 2012 11:57:45 GMT

Great vid! Nice work :)