Community: Message List - Midi mobilizer, Touchosc and 2.0 Firmware

Re: Midi mobilizer, Touchosc and 2.0 Firmware

support@line6.com — Wed, 07 Nov 2012 18:52:43 GMT

I think the Cab options on Ch B for DT50 might be wrong too.

I haven't checked yet, but they don't appear to change. I'll have a look at the file when I get a chance tonight.

Re: Midi mobilizer, Touchosc and 2.0 Firmware

support@line6.com — Wed, 07 Nov 2012 15:32:48 GMT

Sounds possible, Have not tried that myself.

Re: Midi mobilizer, Touchosc and 2.0 Firmware

support@line6.com — Wed, 07 Nov 2012 15:27:04 GMT

I understand from the "MIDI Implementation Guide" that you can configure a DT amp using an HD500 or HD Pro, i.e.

"Got a POD HD500 or POD HD Pro? These devices are capable of functioning as MIDI controllers, where you can configure the specific

MIDI CC messages to be sent from its footswitches & pedals."

So all I have to do is set up an HD patch with the foot controllers configured to send the CC messages for the amp settings I want, and then press the foot controllers, right? And the DT will remember those settings, for the topology configuration on any other HD patch I use?

Has anyone tried this yet? Does it work?

(I don't have a MIDI cable to try it myself, yet)

Re: Midi mobilizer, Touchosc and 2.0 Firmware

support@line6.com — Wed, 07 Nov 2012 12:13:33 GMT

Thanks, I actually got a new midi mobilizer but it only worked twice. At least it worked! However I gave up on the touchosc for now, I am just so tired of it. At least, I got the amp set the way I wanted to.

Re: Midi mobilizer, Touchosc and 2.0 Firmware

support@line6.com — Sat, 03 Nov 2012 05:03:25 GMT

When I turn the knobs on the DT25, i also see the little indicator bar at the top right hand corner of the touchsc flashes red. It is definitely communicating one another but nothing happenes. I think I gave up on this particular unit for now. It shouldn't be this difficult. Thank you,

Re: Midi mobilizer, Touchosc and 2.0 Firmware

support@line6.com — Sat, 03 Nov 2012 03:58:49 GMT

never paid much mind to the lights... but touchosc never looks like anything is really happening... but the sound of course is where i can tell.... i suppose i do see the lights a little... but they don't stream midi to the amp etc...

Re: Midi mobilizer, Touchosc and 2.0 Firmware

support@line6.com — Sat, 03 Nov 2012 03:41:55 GMT

Thanks, it is probably a bad unit. I will go get another mobilizer since it is not that expensive. I downloaded the file from my imac so the zip file issue is not with my case. I see the midi in on the unit flashes red so it is indeed receiving something but nothing chages in the touchsc. The arrow away from the line 6 logo shows nothing active.

Re: Midi mobilizer, Touchosc and 2.0 Firmware

support@line6.com — Sat, 03 Nov 2012 02:41:29 GMT

I just re-tryed it on my ipad3 (wifi/64gb) with iOS6 and it was working like a champ.

fully updated including the latest touchosc.

in the touchosc setting though, it didn't matter whether "midi mobilizer" was enabled or not... it always reported "not connected"

but worked anyway....

must remember to be careful though... nearly blasted my head off switching from an AC30 amp to the SLO overdrive channel... big difference in those.

Re: Midi mobilizer, Touchosc and 2.0 Firmware

support@line6.com — Sat, 03 Nov 2012 01:24:51 GMT

Hi, has the midi bridge worked for you? No luck here, same issue with the mobilizer. Thank you,

Re: Midi mobilizer, Touchosc and 2.0 Firmware

support@line6.com — Fri, 02 Nov 2012 22:57:34 GMT

Any new information about IOS6 issue?