Currently Being ModeratedMar 17, 2011 10:51 AM (in response to Rowbi)Re: JTV59 Korean Pickup type size (standard or F spaced)
With the top E string fretted at the highest fret the gap should be 1.6 mm from underneath the string to the top of the magnet. 2.5 for the bottom E string. This does depend however on the strength of the magnets and the pickups can be lowered a fraction if need be if you notice too much input gain into the amp. I believe this is pretty standard stuff for humbuckers, hope it helps. Line 6 may not do this from factory setups so expect opinions to vary.
Currently Being ModeratedMar 17, 2011 11:30 AM (in response to markcockerill)Re: JTV59 Korean Pickup type size (standard or F spaced)
thanks for the info, but i think you missed what I was asking. I would like to know the distance from the low E to the high E...... in 2 places. once over the bridge pickup and again over the neck pickup of a JTV59 Korean model.
it should be in the region of 48-54mm for both, but the neck measure ment will be a little less.
e.g. on my les pauls here, it's around 50-51mm at the bridge pickup, and 48mm at the neck pickup.... on my Ibanez RG it's about 52.5mm at the bridge pickup and 50mm at the neck pickup.
here's more info on what I mean: taken from here: http://www.dimarzio.com/site/#/faq/ the F,spacing and standard spacing FAQ:
What is F-spacing?
All of our full-size humbuckers except the X2N® are available in two polepiece spacings. F-spacing refers to the wider of the two spacings. For proper string alignment and balanced output, F-spaced humbuckers should be used in the bridge position on all guitars with string spacing at the bridge of 2.1" (53 mm) or greater. On these guitars, if the nut width is 1-11/16 (43 mm) or greater, F-spaced pickups can be used in the neck position as well.
Why are there two different spacings?
A long time ago (in the 20th century, actually) the electric guitar world was divided between Gibson and Fender designs. One of the differences between the two was string spacing. In general, Gibson chose a narrower string spacing at the bridge than Fender, and therefore the polepieces on Gibson humbuckers were closer together than the magnets on Fender pickups. When guitar shops started installing humbuckers in the bridge position of Strats, it was obvious that the strings didn’t line up with the polepieces, and if the E strings were too far outside, the sound could suffer. Our first humbuckers followed the original Gibson spacing, and we call them standard-spaced. When we released our first humbuckers with wider spacing, Floyd Rose bridges were very popular. Floyd string-spacing is the same as Fender spacing, so we naturally called the new pickups F-spaced.
How do I know which spacing to use?
F-spaced pickups measure 2.01" (51 mm) center-to-center from the first polepiece to the sixth. Standard-spaced pickups measure 1.90" (48 mm). Although some players believe that F-spaced pickups are only for the bridge position of tremolo bridge guitars, many guitars with fixed bridges (including late 1990s Gibson Les Pauls and Epiphone LPs) should have F-spaced pickups in the bridge position. Most tremolo equipped guitars that have a nut width of 1-11/16 (43mm) or more should also use an F-spaced pickup in the neck position. If you’re replacing a bridge-position pickup and you're not sure what your string-spacing is, it's usually better to get an F-spaced model. It is not necessary for the strings to pass exactly over the center of the polepieces for best performance, but it is wise to avoid a situation where the E strings are sitting completely outside of the outer polepieces.
If you're talking about Seymour duncans, F spacing is called a trembucker.
Currently Being ModeratedMar 18, 2011 7:59 AM (in response to Rowbi)Re: Calling anyone with a Korean JTV59...
Can anyone measure this for me as I'd be really grateful? it should only take a few seconds to measure from high to low E string twice (once over each pickup) in milimetres.
I just want to get my replacement magnetic pickups ordered now (while I can get them at a discounted price) ready for when I take delivery of my 59... I'm thinking about maybe a Dimarzio Tone Zone in the bridge, and something more vintage in the Neck!
thanks to whoever can help, as I really need this info ASAP.
Message was edited by: Rowbi
Currently Being ModeratedMar 18, 2011 11:26 PM (in response to Rowbi)Re: Calling anyone with a Korean JTV59...
Sorry Rowbi, been away on business and just got back.
On the Korean JTV-59, the distance between high and low E strings over the bridge is 50.5mm. Over the neck pickup it's 48.0mm.
Currently Being ModeratedMar 19, 2011 2:19 AM (in response to ozbadman)Re: Calling anyone with a Korean JTV59...
Thanks for doing that David.
so it looks like it's a standard spacing for the neck pickup, but the bridge pickup is borderline between both... but based on the Dimarzio information (F spacing poles are 50mm apart) and Seymour duncan's info nere: http://www.seymourduncan.com/support/faq/frequently-asked/everything-else/what_does_tremb/
I think I'm gonna go for trembucker or f spacing for the bridge.
Now I just need to totally make my mind up about pickups. I'm swaying to a DImarzio super distortion and humbucker from hell now....