Please ensure Javascript is enabled for purposes of website accessibility Jump to content

Search the Community

Showing results for tags 'mixer block'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Community Support
    • Multi-Effects Units
    • Variax Instruments
    • Amplifiers
    • Computer Based Recording
    • Live Sound
    • Pedals/Controllers
    • Dream Rig - Line 6 Product Integration
  • General Discussion
    • Tone Discussion
    • Line 6 Lounge

Categories

  • General FAQ
    • Operating System-specific Information
  • Tutorial Videos
  • Effects/Controllers
    • HELIX/HX
    • DL4 MkII Stompbox Modeler
    • M5
    • FBV Controllers (MKII / 3)
  • Amplifiers
    • Catalyst
    • Powercab
    • Spider V
  • POD
    • POD Go
    • POD Express
    • Pocket POD
  • Guitars
    • JTV / Shuriken / Variax Standard / Workbench HD
  • Relay G10 Digital Wireless
  • Recording
    • Helix Native
    • Metallurgy
    • Echo Farm/Amp Farm
    • POD Farm 1/2.0/2.5
    • Computer Audio Set Up and Troubleshooting
  • Legacy Products
    • POD
    • Amps
    • 1st Gen Variax Guitars / Bass / Workbench
    • Effects and Controllers
    • AMPLIFi Series
    • Live Sound
    • Digital Wireless
    • Mobile Products
    • POD Studio / Tone Port / GuitarPort
    • Software
    • Dream Rig

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Location


Interests


Registered Products

Found 2 results

  1. Hello! The Pod HD 500x internal routing is really confusing and I´ve been reading and searching through the forum, but I´m still not getting it. My current settup is my bass going in to the pod hd, then I have a single signal path with different fx blocks going into a single amp model BEFORE the split and then the L mixer pan at 0% with 0 db and R at mute. After the mixer I have 2 more fx blocks. One of the fx blocks before the amp model (second block) is a fx loop with an external drive pedal. This setup sounds really good and I´m quite happy with the sounds I´m getting. One thing that would improve my tone is by somehow being able to mix the distorted signal from my external drive with my clean tone so I don´t loose all my low end when I engage the fx loop/external drive. I know there are external blend pedals that work but it ought to be possible to do this internaly? If I move my amp AFTER the mixer I have the possibility to get to signals into my amp, one "clean"/fx and another one with my FX loop and external drive. The problem is when you do this it is possible to boost the amp with the mixer. To my question: How do you set the mixer settings with path A + B so you have the SAME signal hitting the amp block AFTER the mixer, compared as if you had the amp block before the mixer (with above mentioned settings)? I´m mostly using it with headphones so I want to be able to get sound in both ears! Besides that, mono is totaly ok. Or should I just buy an external blender? /Danne
  2. JTV/VDI>PODHD500/L6>DT25 Using different models with different voicings, I've never, ever been able to get my patches level across both the DT speaker and the DT D.I. in the year that I've had it. I spend most of my time in LVM but this also is the case in Full Vol. w/preamps It's mostly the models that use voicing 3 on the DT. Matched at speaker volume (AND matched listening through the pod's own headphone jack), they become way quieter in the DI (relative to the other voices in all cases). (See my test settings below) After emailing tech support numerous times I finally got a useable answer as to why this was, and I was NOT happy. "Unfortunately on DT25 amp the Master Vol on the DT25 does not control DI at all. The DI is controlled by the output of the modeling amps used on the POD. Sorry if this isn't ideal for your set up." How would that be ideal for anyone's setup? If the DI on your amp doesn't actually reflect what's coming out of your amp, that is, well, I guess I can't get my head around that. Totally not ideal. I'm guessing that this all is reflective of a L6 hookup between the pod and the dt? I also guess that's why the the pent/tri or class switches do nothing to the DI sound. What about when the dt is used standalone? Is the DI signal pre-master vol? Is it the same situation for LVM and Full Vol? Can I set the master vol on the dt so it will at least be closer matched to the pod's output? Or vice versa? The patches are level at the DT speaker. The patches are level at the POD hedphone out. Why in the holy f*%k are they not level at the DT's DI?!?!?!??? Because the sonics that come from your amp, which you're trying to duplicate via an output on that very same amp is not actually being controlled from nor does it sound like your amp. Absolutely brilliant. Anyone have anything to add? Please have something to add... System settings: (for all patches) Input 1: guitar+variax Input 2: variax Mixer block: Path A +0dB center panned Path B mute I also set every single patch to Class A/B Pentode and an identical JTV setting. POD mstr vol: 75% DT mstr vol: 75%
×
×
  • Create New...