Segomil Posted December 29, 2014 Share Posted December 29, 2014 Hi I just wrote to Steinberg because since i bought & install Cubase 8 artist, problems have start to appear ! It was not the case with 7.5 ... So i write to Line 6 also, because i think that Line 6 still haven't functionnal driver for Cubase 8 ! I have start a v7.5 project through v8 with the audio interface ( HD500X ) Line 6. In the line midi/audio device it have : driver format with the sound control panel It's where you select the audio quality ex: 44-48 hz,16/24 bits ect... it constantly says ; inactive ? ... ... & my project return to AsioAll or generic low latency asio ect ... i can't fix that ! It's like that the HD500X asio driver disappear ?! .............But it still there ! Anyone have notice something like that ? I do not know if Cubase 8 come with Asio driver included, is that the case ?, because I have an other Asio driver installed, it called : AsioALL made by Michael Teppach !, Do i have to uninstalled it ? Is it serious at the point that puts my project in peril ... In VST Audio system (in V8) which Asio driver can make the case while waiting a fix without degrading the quality? I think it's not serious as much as this variax that i have ordered which had been used & dirties & soiled : 5 weeks of waiting for dust ! Now that i'm stuck with the HD500X (bought one month ago (variax was for it)) can i have an answer about the drivers ? Thank you all Segomil 1 Quote Link to comment Share on other sites More sharing options...
gunpointmetal Posted December 29, 2014 Share Posted December 29, 2014 There shouldn't be a specific driver just for cubase with the POD. Are you settings from your project saved in an earlier version of Cubase the same as the current one as far the bit depth and I/O are concerned? Quote Link to comment Share on other sites More sharing options...
Segomil Posted December 30, 2014 Author Share Posted December 30, 2014 I have launched (loaded) a Cubase 7.5 project but through Cubase 8 with the same settings , that is to say : 24 bits 44-48 hhz. & About the I/O , as i say i cannot use the HD500X ... ***But i just notice something more shocking ; it's a strange behavior that when i record audio (guitar) and than i activates the monitor button in Cubase, it's like reverb effect or something like 2 guitar that is heard...there is a delay ! & without the monitor button, the guitar sound is heard in the Eris through the HD500X, but when i activate the button, suddenly it's like a second guitar with more noise & artefact. (there is no effect activated at all on any tracks), If I drop the (fader mixeconsole) cursor down of the track to cut the strange sound, the guitar volume is not enough to be recorded ! I have two presonus Eris 8 speaker plugged to the HD500X. weird ! Is There a volume for the HD500X headphone, because it's problematic with DAW?! Quote Link to comment Share on other sites More sharing options...
silverhead Posted December 30, 2014 Share Posted December 30, 2014 Using ASIO4ALL is known to cause problems with Line 6 devices. It is not a compliant ASIO driver. You must use the the Pod HD500 driver that is provided by Line 6. With your HD500 connectd, run Line 6 Monkey to make sure you have the current driver installed. Then configure Cubase to use the HD500 as the audio device, and also to use its ASIO driver. You must remove ASIO4ALL from your configuration in order to receive further support with this issue. Quote Link to comment Share on other sites More sharing options...
Segomil Posted December 30, 2014 Author Share Posted December 30, 2014 Yes , i have uninstall the AsioAll yesterday morning & all third party plugins ( even korg m1 plugins which is important for me) , & start a new project in CUbase 8 but everything is the same. This morning i launched Cubase 8 with this new project & again the HD500X driver won't loaded. The message said buffer is too high ... however my latency is ALWAYS set to 512 or higher if the projects become bigger, If I increase it over 512 bytes in the device setup control panel for the interface in cubase the error message says that i have lost my connexion with HD500X but Dropping the latency under 512 results in almost no audio at all but with random clicks and pops ect ... Before i bought the HD500X , i was with the Steinberg UR22 interface that worked good ... My spec : CUBASE 8 FX8350 (8 CORE) ASUS M5A99FX RAM 16 GIGS at 1600 hZ DDR3 RADEON R7 265X 2GIG MEMORY 2x SSD hard disk drive + 2HDD hard disk = 3T LOGICKEYBOARD for CUBASE PRESONUS TUBEpreV2 PRESONUS ERIS 8 LINE 6 HD500X RODE NT1-A NOVATION LAUNCHKEY MIDI KEYBOARD FENDER MUSTANG III V2 FENDER STRAT Quote Link to comment Share on other sites More sharing options...
Segomil Posted June 23, 2015 Author Share Posted June 23, 2015 Hi It's really the HD500X the problem...i always lost the signal with the POD & i am forced to swicth to generic drivers which switch me to my tiny speakers, instead my presonus Eris 8 which is connected to the POD. Each time i lost the signal with the POD i have to disconnect the power switch (wait 5 sec) & reconnect it & select the POD in Cubase 8 ...i'm tired oh this ! Do you have any REAL idea ... how can i create like this ? ,,, i have done nothing for the last 2 months ! ... I AM NOT JOKING My spec : CUBASE 8 FX8350 (8 CORE) ASUS M5A99FX RAM 16 GIGS at 1600 hZ DDR3 RADEON R7 265X 2GIG MEMORY 2x SSD hard disk drive + 2HDD hard disk = 3T LOGICKEYBOARD for CUBASE PRESONUS TUBEpreV2 PRESONUS ERIS 8 LINE 6 HD500X RODE NT1-A NOVATION LAUNCHKEY MIDI KEYBOARD FENDER MUSTANG III V2 FENDER STRAT Quote Link to comment Share on other sites More sharing options...
panaman Posted June 24, 2015 Share Posted June 24, 2015 use spdif, unfortunately your board (which has everything else) doesnt have spdif in. there are cheap add on pci(e) solutions. they should come with their own asio drivers. note there can be only 1 asio device per system, no 2 drivers or input on a different device than output you have enough horsepower for sure. the pod is trying to be everything at once but it really is having a hard time with that. thats not to say it cant be used as a soundcard. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.