guilhordas Posted July 18, 2013 Share Posted July 18, 2013 my pod hd is lowering the volume suddenly, I can not figure out where the problem is, I seem to internal Quote Link to comment Share on other sites More sharing options...
Darkside-prince Posted July 19, 2013 Share Posted July 19, 2013 I'll quote what i told the other guy with the same problem: " I used to have this problem specially when I palm muted 1-first I have to recommend u to update ur pod hd300 flash memory firmware to version 2 , if it is already re-install it , wont hurt 2-2nd What ur experiencing might be the act of The pod hd300 sound normalizer , which means ur channel is too loud and it reduces the volume to prevent amp overloads , so the solution is decreasing ur channel volume and increasing the overall (output) volume from the back of ur HD300 , this way u can both have a loud and un-normalized sound which is cool right sorry for being so thorough but I wanted to explain completely so u could solve ur problem without any trouble if possible so what u have to do is : before anything update ur firmware , then if it didnt work lower the channel volume" Quote Link to comment Share on other sites More sharing options...
guilhordas Posted July 19, 2013 Author Share Posted July 19, 2013 I dnt have podhd300 , mine is pod hd500 Quote Link to comment Share on other sites More sharing options...
guilhordas Posted July 19, 2013 Author Share Posted July 19, 2013 http://www.youtube.com/watch?v=fgq7mxFBkeo A similar problem? my problem is during the gig, I'm playing and suddenly the sound lowers Quote Link to comment Share on other sites More sharing options...
Darkside-prince Posted July 19, 2013 Share Posted July 19, 2013 dude thats not the point just follow the instructions , use the monkey to update ur firmware , if it didnt work lower the channel volume ;) Quote Link to comment Share on other sites More sharing options...
guilhordas Posted July 19, 2013 Author Share Posted July 19, 2013 dude thats not the point just follow the instructions , use the monkey to update ur firmware , if it didnt work lower the channel volume ;) I already did the update the unit, you are saying to do it again? on the volume, you mean that the volume of the patch (amp) may be too high? Quote Link to comment Share on other sites More sharing options...
evilmikehoo Posted July 19, 2013 Share Posted July 19, 2013 Just a shot in the dark. Did you say this only happens during a gig? Does it seem to happen at a particular location? If so, could be dirty power. If that's the case, a power conditioner could solve your problem. Quote Link to comment Share on other sites More sharing options...
guilhordas Posted July 19, 2013 Author Share Posted July 19, 2013 If i reisntal the firmware Will I loose my patchs? Quote Link to comment Share on other sites More sharing options...
guilhordas Posted July 19, 2013 Author Share Posted July 19, 2013 Just a shot in the dark. Did you say this only happens during a gig? Does it seem to happen at a particular location? If so, could be dirty power. If that's the case, a power conditioner could solve your problem. Not during a specific gig, in any location or situation Quote Link to comment Share on other sites More sharing options...
Darkside-prince Posted July 19, 2013 Share Posted July 19, 2013 If u re-install firmware u might get a different tone so Its good to use pod edit , click on file->save bundle , this will save ur patches but while ur at it , yeah I was talking about ur Amp volume on ur HD500 , in the Amp section of pod edit its indicated as CH VOL lower it a little , this should solve ur problem ;) Quote Link to comment Share on other sites More sharing options...
guilhordas Posted July 19, 2013 Author Share Posted July 19, 2013 In clean patchs , tweed amp, i use 60% in volume e15% in gain, in mixer I set in 9 db both channels Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.