Relay G10TII Information
Important Information About the G10TII Transmitter
· The recommended charging temperature range of the G10TII transmitter is specified as 50° F to 86° F (10° C to 30° C).
· The recommended operating temperature range of the G10TII transmitter is specified as 32° F to 122° F (0° C to 50° C).
· Line 6 recommends charging the G10TII transmitter at least every 6 months, based on best practices for lithium-ion batteries.
· G10TII LED behavior is as follows:
|
G10TII Transmitter (Docked in G10/G10S Receiver, POD Go Wireless, Spider V amp or THR10II/THR30II/THR30IIA Wireless amp)* |
|
|
LED State |
Condition |
|
Red (slow flash) |
Charging, less than 30 minutes battery time remaining † |
|
Green (slow flash) |
Charging, more than 30 minutes battery time remaining |
|
Green (solid) |
Fully charged ‡ |
|
Dim Red/Pink, may turn off |
G10TII is not docked properly – Try un-docking and re-docking 5-10 times |
|
Red (three quick flashes, repeating) |
G10T charging has stopped due to exceeding supported temperature. Charging will resume after 5 minutes at 50° F to 86° F (10° C to 30° C) § |
|
Orange (solid) |
Docked and connected to Mac or PC, firmware update in progress |
|
Off |
Receiver not powered (transmitter enters sleep mode after 4 minutes if receiver power is disconnected) |
|
G10TII Transmitter (Connected to Instrument) |
|
|
LED State |
Condition |
|
Green (solid) |
Transmitting, more than 30 minutes battery time remaining |
|
Red (slow flash) |
Transmitting, less than 30 minutes battery time remaining |
|
Off |
Connected to an instrument but not enough battery to transmit ‖ or Removed from instrument |
*When the G10TII is docked in a receiver or Relay-Ready device, the G10TII LED initially indicates amber, red, or green, depending on its current battery state. This is followed by four flashes (red) as the device initializes. Once this completes, the G10TII LED proceeds to indicate its remaining battery time.
† All values stated for amount of battery time remaining are approximate, and the exact amount of battery time remaining when an LED state is indicated may vary slightly between charges. When the G10TII flashes red, it may have up to 60 minutes of battery time remaining.
‡ If the G10TII reaches a full charge (solid green) and remains docked, the G10TII LED may eventually flash green again. This is expected behavior as the G10TII may discharge slightly after reaching a full charge, and its LED may then flash green until it again reaches a full charge.
‖ When the G10TII has insufficient power to transmit, its LED may indicate a pattern of five quick red flashes when connected to an instrument and audio is detected. This is the expected behavior.
|
LED State |
Condition |
|
White (solid) |
G10TII charging or fully charged |
|
White (flicker) |
System has auto-scanned and is changing its channel |
|
Red (flash) |
G10TII not docked properly – Try undocking and redocking |
|
Pink (pulse) |
Connected to Mac or PC, Line 6 Updater open |
|
Pink (solid) |
Connected to Mac or PC, firmware update in progress |
|
Off |
No power to receiver |
|
G10 Receiver (G10TII Transmitter un-docked) |
|
|
LED State |
Condition |
|
White (solid) |
G10TII transmission received, more than 30 minutes of runtime |
|
Red (slow flash) |
G10TII transmission received, less than 30 minutes of runtime |
|
White (pulse) |
Receiver on but no G10TII transmission received |
|
White (flicker) |
G10TII transmission dropout (RF mute) |
|
Off |
No power to receiver |
|
LED State |
Condition |
|
|
Battery LEDs |
Green (cycle 1-2-3) |
G10TII charging |
|
3 Green LEDs (solid) |
G10TII fully charged |
|
|
RF LEDs |
3 Red LEDs (solid) |
More than 75% interference (not usable) |
|
2 Red LEDs (solid) |
50% interference (usable, but only for short range) |
|
|
1 Red LED (solid) |
25% interference (usable, also indicates G10S power on) |
|
|
Battery LEDs Off RF LEDs On |
Battery LEDs – Off RF LEDs – Red (cycle 3-2-1) |
G10TII not docked properly – Try undocking and redocking |
|
Battery LEDs – Off RF LEDs – 3 Red LEDs (solid) |
Connected to Mac or PC, Line 6 Updater open |
|
|
All LEDs Off |
|
No power to receiver |
|
G10S Receiver (G10TII Transmitter un-docked) |
||
|
LED State |
Condition |
|
|
Battery LEDs |
3 Green LEDs (solid) |
G10TII transmission received, more than 4.5 hours of runtime* |
|
2 Green LEDs (solid) |
G10TII transmission received, more than 3 hours of runtime |
|
|
1 Green LED (solid) |
G10TII transmission received, more than 1.5 hours of runtime |
|
|
1 Red LED (solid) |
G10TII transmission received, more than 30 minutes of runtime |
|
|
1 Red LED (flash) |
G10TII transmission received, less than 30 minutes of runtime |
|
|
RF LEDs |
3 Green LEDs (solid) |
G10TII transmission received, good signal strength |
|
2 Green LEDs (solid) |
G10TII transmission received, average signal strength |
|
|
1 Green LED (solid) |
G10TII transmission received, poor signal strength |
|
|
3 Red LEDs (solid) |
No G10TII transmission received, more than 75% interference (not usable) |
|
|
2 Red LEDs (solid) |
No G10TII transmission received, 50% interference (usable, but only for short range) |
|
|
1 Red LED (solid) |
No G10TII transmission received, 25% interference (usable, also indicates G10S power on) |
|
|
Red (cycle 3-2-1) |
G10S channel knob has been changed from its setting since G10TII was last docked |
|
|
All LEDs off |
|
No power to receiver |
* All values stated for amount of battery time remaining are approximate, and the exact amount of battery time remaining when a LED state is indicated on the G10S receiver may vary slightly between charges of the G10TII Transmitter.