Jump to content

Search the Community

Showing results for tags 'stopped working'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Community Support
    • Multi-Effects Units
    • Variax Instruments
    • Amplifiers
    • Computer Based Recording
    • Live Sound
    • Pedals/Controllers
    • Dream Rig - Line 6 Product Integration
  • General Discussion
    • Share your Settings
    • Line 6 Lounge

Categories

  • General FAQ
    • Operating System-specific Information
  • Tutorial Videos
  • Effects/Controllers
    • HELIX/HX
    • DL-4 Stompbox Modeler
    • FBV Controllers (MKII / 3)
    • M5
    • Firehawk FX
  • Recording
    • Helix Native
    • Metallurgy
    • Echo Farm/Amp Farm
    • POD Farm / POD Studio / TonePort
    • Computer Audio Set Up and Troubleshooting
  • Amplifiers
    • Catalyst
    • Spider V
    • Powercab
    • Spider IV/Spider Online
    • Spider Jam
  • POD
    • POD Go
    • POD HD X
    • Pocket POD
  • Guitars
    • JTV / Shuriken / Variax Standard / Workbench HD
  • Relay/XD-V Digital Wireless
  • Legacy Products
    • POD
    • Amps
    • Mobile Products
    • Effects and Controllers
    • AMPLIFi Series
    • Live Sound
    • Digital Wireless
    • 1st Gen Variax Guitars / Bass / Workbench
    • Software
    • Dream Rig
    • POD Studio / Tone Port / GuitarPort

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Location


Interests


Registered Products

Found 2 results

  1. I’ve been gigging with Helix LT for several years just fine (XLR left output direct into mixer). At band practice last night volume decreased and then came back, and it started clicking/popping. Then it stopped working. No sound. Then bottom row of buttons made some noise, and top row worked ok, then stopped again. Same when changing banks. Tried power off – nope, change guitar cable – nope. Then it began working like normal, but had a few seconds randomly dropping out. Seems to be working fine now, but I am skeptical. Any ideas what the problem is? Thanks, Joel
  2. My Pod Studio UX2 has suddenly stopped outputting any audio after several months of solid use. I have already checked the monkey (everything shows up as green check marks), reinstalled drivers, and checked my audio system to make sure the obvious stuff is set up properly (correct audio out selected, volume turned up, audio cables and USB cables swapped out, speakers are working when plugged into another audio source, etc). I am running Windows 7. The drivers are definitely working, in that when I plug it in the volume controls all switch from my laptop's built in sound card to the Line 6 UX2 and the meters on the UX2 light up and show audio coming through it. Plugging speakers or headphones into it gives that telltale 'pop' that you get when you plug a speaker up to a powered-on amp without any audio signal coming through yet, so I believe that the audio amp has power, but there is no sound coming out at all. My windows volume mixer shows an audio signal going to the UX2. In the Line 6 Audio-Midi Devices settings in the control panel, Hardware Meters are set to show audio output, and it is definitely showing that it is receiving a signal as I can play music and the meters show the music's volume levels without problems. Again, everything looks like it should work, but there is just no audio at all, either from the analog outs or the headphone jack. To be clear, this is audio from any source, not just my live guitar input processed through Pod Farm. I can play movies, music, etc from my computer and get no audio from any sources at all. What happened? Is my Pod Studio shot?
×
×
  • Create New...