boynigel Posted Wednesday at 02:11 PM Share Posted Wednesday at 02:11 PM If the manual gives a value or suggestion, shoot me- because i can't find any such info in there. I've been running everything at -6.0, that way i have somewhere to go volume-wise, if need be, but i'm wondering if it's recommended to be closer to 0.0 for any reason? Quote Link to comment Share on other sites More sharing options...
silverhead Posted Wednesday at 02:56 PM Share Posted Wednesday at 02:56 PM There’s an industry standard called ‘unity gain’ which I believe represents a standard input/output signal level strength. I think devices are built to accept this level of input and send this level of output at some default setting. No idea if my layman’s understanding is correct or what the definition is in physical terms. I would welcome more informed insights on this, expressed without needing an understanding of physics. i.e. no mention of loudness metering or a need for knowledge of what a ‘db’ is. I believe Line 6 products are built to send unity gain output when the Volume knob is maxed. I think this also minimizes the signal-to-noise ratio in the signal meaning the signal is cleaner. So theoretically when the Vol knob is maxed the external mixer or PA receives the ‘ideal’ signal strength with minimal noise. Again, theoretically, if the Vol knob is less than max the person operating the mixer/PA may have to adjust the Input Trim setting to compensate for the less-than-unity gain incoming signal. But frankly I’ve never heard any difference in the end result if the Vol knob is not maxed out. Quote Link to comment Share on other sites More sharing options...
theElevators Posted Wednesday at 05:37 PM Share Posted Wednesday at 05:37 PM It's simple. Set your output level to "microphone" for XLRs. These go to your FOH. The whole point of these Left/Right signals is they do not change, because otherwise you would be overriding what the sound guy is running for your guitar. So set up your volume knob to not affect the XLR volume, only 1/4" outputs. Also--no Global EQ should be applied to XLRs. That's the rule of how the processor should be run. XLRs go to FOH. 1/4" go to your FRFR .... or in my case to a power amp + guitar cab. You use the volume knob to adjust your on-stage volume. If the stage is too boomy, I apply the Global EQ to the 1/4" only. I do not create any additional output path where the amp/cab sim are bypassed. Just the same exact signal always goes to "multi". I've been doing it this way and have not had any complaints. When building your presets, the fully-loaded preset with actual blocks should be about as loud as the blank "New Preset" preset. If it's slightly different it's not a problem. So when building it, toggle back and forth and check if your preset is louder/softer than the blank preset and make adjustments. No need for any exact measurements, just use your ear. That's all there is to it. Quote Link to comment Share on other sites More sharing options...
boynigel Posted yesterday at 01:47 AM Author Share Posted yesterday at 01:47 AM On 11/18/2026 at 12:37 PM, theElevators said: It's simple. Set your output level to "microphone" for XLRs. These go to your FOH. The whole point of these Left/Right signals is they do not change, because otherwise you would be overriding what the sound guy is running for your guitar. So set up your volume knob to not affect the XLR volume, only 1/4" outputs. Also--no Global EQ should be applied to XLRs. That's the rule of how the processor should be run. XLRs go to FOH. 1/4" go to your FRFR .... or in my case to a power amp + guitar cab. You use the volume knob to adjust your on-stage volume. If the stage is too boomy, I apply the Global EQ to the 1/4" only. I do not create any additional output path where the amp/cab sim are bypassed. Just the same exact signal always goes to "multi". I've been doing it this way and have not had any complaints. When building your presets, the fully-loaded preset with actual blocks should be about as loud as the blank "New Preset" preset. If it's slightly different it's not a problem. So when building it, toggle back and forth and check if your preset is louder/softer than the blank preset and make adjustments. No need for any exact measurements, just use your ear. That's all there is to it. as far as not using global EQ on the XLR outs, i've always employed Global with a high cut at 11.5 khz (6db/octave), w/everything else on the global left flat. never had any issues or complaints from sound guy. am i missing something or were you just speaking more to not using global EQ with busier, more aggressive cuts/boosts? Quote Link to comment Share on other sites More sharing options...
theElevators Posted yesterday at 03:06 AM Share Posted yesterday at 03:06 AM On 11/18/2026 at 8:47 PM, boynigel said: as far as not using global EQ on the XLR outs, i've always employed Global with a high cut at 11.5 khz (6db/octave), w/everything else on the global left flat. never had any issues or complaints from sound guy. am i missing something or were you just speaking more to not using global EQ with busier, more aggressive cuts/boosts? A lot of people treat Global EQ as an additional tone-shaping tool. However, the purpose of it is to be able to address problems of the overall mix on stage, and only on stage. So your presets should already be perfect and gig-ready without Global EQ. You can use the amp parameters, add EQ blocks, etc in your presets. I'm speaking from experience... 99% of the time, I run my sound completely unaltered, Global EQ is off. XLR out to FOH (no Global EQ). 1/4" to power amp + cab for stage volume (no Global EQ). When to use Global EQ? When I played in theaters in Europe, the stage could be very lively and project into the audience more than you would get in some other venues. In those rare scenarios my power amp + cab (which is purely my personal monitor and not mic'ed) would create problems for the overall band mix. So in those cases, Global EQ helped me to address these problems on stage. The sound guy would go to my Helix and tweak the sound until the sound in the theater that people would hear was acceptable. This is a very rare scenario, but it's come up several times with me. But again, the Global EQ would only apply to the 1/4" out and never to XLRs out. FOH engineers can apply whatever EQ is needed themselves, no need to shape the tone for them. Once you cut certain frequencies out, it's difficult to put them back, you know what I'm saying? Sometimes you are playing on stage and the room is so bright-sounding, that it becomes very painful. Again -- Global EQ to the rescue! Dial down those highs, etc. So in summary, this is the best practice for how to use and not use Global EQ--use it to fix problems. No problems? Global EQ should be off. Quote Link to comment Share on other sites More sharing options...
boynigel Posted yesterday at 03:06 PM Author Share Posted yesterday at 03:06 PM On 11/18/2026 at 10:06 PM, theElevators said: A lot of people treat Global EQ as an additional tone-shaping tool. However, the purpose of it is to be able to address problems of the overall mix on stage, and only on stage. So your presets should already be perfect and gig-ready without Global EQ. You can use the amp parameters, add EQ blocks, etc in your presets. I'm speaking from experience... 99% of the time, I run my sound completely unaltered, Global EQ is off. XLR out to FOH (no Global EQ). 1/4" to power amp + cab for stage volume (no Global EQ). When to use Global EQ? When I played in theaters in Europe, the stage could be very lively and project into the audience more than you would get in some other venues. In those rare scenarios my power amp + cab (which is purely my personal monitor and not mic'ed) would create problems for the overall band mix. So in those cases, Global EQ helped me to address these problems on stage. The sound guy would go to my Helix and tweak the sound until the sound in the theater that people would hear was acceptable. This is a very rare scenario, but it's come up several times with me. But again, the Global EQ would only apply to the 1/4" out and never to XLRs out. FOH engineers can apply whatever EQ is needed themselves, no need to shape the tone for them. Once you cut certain frequencies out, it's difficult to put them back, you know what I'm saying? Sometimes you are playing on stage and the room is so bright-sounding, that it becomes very painful. Again -- Global EQ to the rescue! Dial down those highs, etc. So in summary, this is the best practice for how to use and not use Global EQ--use it to fix problems. No problems? Global EQ should be off. a key point i left out is that i use the 11.5 khz high cut in my Global as part of a multi-step "formula" to dial out the sizzle. that said, this is something that got carried over to my stadium xl from my OG LT presets...on which i definitely preferred to have said cut applied. when i migrated all my LT stuff to Stadium, i never A/B'd the global EQ (creature of habit). Maybe the new Augora amps that i'm now using w/my presets won't require it though? I'll A/B when i get home tonight. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.