Jump to content

JaseFIJo

Members
  • Content Count

    31
  • Joined

  • Last visited

Community Reputation

5 Neutral

About JaseFIJo

  • Rank
    Just Startin'

Profile Information

  • Registered Products
    9

Recent Profile Visitors

257 profile views
  1. JaseFIJo

    Updater Not Recognizing Equipment

    I know think it's a USB3.0 v 2.0 fired up an old machine with Windows 10 and USM 2.0 ports 1. When plugging in the Transmitter the driver didn't auto load at first but the trouble shooter actually worked! and installed the driver. 2. Downloaded the Updater, logged in 3. Device recognised 4. Updated the firmware with no issues Not sure if this would be important but also had the auto sleep mode switch in the off position. Transmitter now at most recent firmware.
  2. JaseFIJo

    Updater Not Recognizing Equipment

    I have a similar issue at the moment, updated the base unit no problem, went to update the TB516G and the updater program states "The Transmitter was not detected correctly". I have opened ticket with support and are being helpful, so far have suggested. 1. http://line6.com/support/page/kb/_/live-sound/relay-digital-wireless/how-to-update-relay-g7075-transmitter-and-rece-r807 Make sure you've installed the latest version of Line 6 Updater (v1.12) and try updating in offline mode. For this, please download the TB516G flash memory file v1.03 from our website: http://line6.com/software/ Connect the transmitter via USB to your computer, launch Line 6 Updater, don't login, choose "offline mode" instead. Then select the downloaded file and try to repeat the update. Also test it with different USB ports and another USB cable. Don't connect to an USB hub. If still not working, please test it with another computer, if possible. Which I have been through, when I try and connect same report. I suspect that is a driver type issue maybe specific to Windows 10 which I have also running on a surface pro. Attached are the event reports for the device, where something is not finalising with the driver install. It is also suggested that your remove the batteries from the Transmitter for an update and there is a 5 secs on/off reset should things not go to plan If you are not seeing anything in the updater window then the device driver has probably not installed correctly or you have a cable fault. If you look in Devices and Printers you should see and Unspecified device called USB-Serial (Single Channel) - this is what mine registers as anyway. If you right click and run the trouble shooter it reports the device is a composite older USB that may not work with USB 3.0. So I'm off to find a USB 2.0 port on another machine! If I solve it or Support come up with something then I will post
  3. Thanks guys unfortunately it's not new and out of warranty, I've had it 21+ months. I've got no service centres near me at all and shipping guitars with couriers just adds to the risk of other s**t happening! Arrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrgh
  4. So after a few re-installs and reflashes I've got Standard tuning to Dropped D and Dropped D is Dropped Bb, 1/2 down doesn't appear to change anything now. It would appear looking back at history others have had simliar issues in the past that cleared up!. The tone on the modelling sounds pretty poor so there's something else going on. Anyway my best theory is that the rotor switch for the alt-tuning is not working consistently for the first few tunings. Does any one know what a Green LED means on this switch?
  5. Dropped D stays the same as the new Standard, 1/2 down goes another half down , 1 down seems go another 1/2 down and the rest seem ok Haven't touched a thing since the last firmware updated to 2.21 months ago, haven't connected to HD workbench and haven't added any customer of virtual capos from the guitar recently. Any ideas? I've now connected and rolled back the firmware from monkey (same problems which seems weird), updated back to 2.21 and then reinstalled 2.21 no changes to the symptoms above. Jason
  6. JaseFIJo

    M20d - Pad inputs?

    So the answer to my own queston is use channels 1-12 XLR to 1/4 TRS cable. Connect this way and all the digital process chains are available
  7. JaseFIJo

    M20d - Pad inputs?

    Just to add to this thread the output direct from a H&K is "too hot" for either input the MIC XLR (1-12) or LINE (12-16). Just had a test session with our lead guitarist and couldn't really make much sense of it other than have the trim at the lowest value which is +6dB. Output from the PA didn't sound too bad even though you could see that there was a fair amount of clipping going on. Probably needs some kind of attenuator in the loop before connection to the desk. Which leads me to a question, if you use the LINE in then the dynamic digital processing line is just "basic" i.e comp and EQ. How do you select something like the uber setting? Which has things like gate and limiter using the limiter may help with this.
  8. Wow this thread and some others I have read seem to point a very common type of issue. It would appear to me that some type of change has taken place over older versus newer M20d or just plain build quality. I "had" a M20d, still have one if I'm fair but have not seen it very quiet some time! It started exhibiting all the common modes of failure, channel level drops, left main out output fading then recovering, working fine for 3/4 of a gig then fading for a while etc etc. You can put this down to some or all of the issues that have been highlighted in previous posts. My view it's a common hardware fault so updates, patches and all the iApps! in the World won't fix it. If you have this issue and it's within warranty then send it back to be resolved, pain in the arse but it's the only way. So FYI, for those of you out there and it's not a great story so far. Dropped off the unit April 10th 2015 at Guitar Guitar Glasgow, they did point out at the time that they were experiencing a few issues with turnarounds citing the Yamaha>Line6 take over. Didn't think much of it until I phoned for an update May 10th and May 29th both times the key component (circuit board) assume this is the input board as looking at the picture(s) doesn't look like there are many others had an Estimated date 15th August 2015. Potentially five and a bit months down time in the first year!!! if this is indicative of all the other things reported around the M20d, the Line 6 MTTR and MTBF must look shocking. Shout out to the guys at Guitar Guitar, they have been great :D but they really can't do anything with regard to internal parts delivery Anyone from Line6 listening?
  9. JaseFIJo

    Any tips on how to keep the handle on?

    Mark If the handle is anything like the DT50 I have then the screws thread into some form of nut with spikes into the under side of the case not the amp chassis. If they've all gone walkies then I'd worry where they dropped to, if they have stripped then they are goosed. Longer screws and some compatible nuts, small washer and lock-tight will have the same effect and will hold the handle on.
  10. JaseFIJo

    Compatible 2x12" cabinets

    Had the DT50 head for a while and have been running it through my single 12" Blackstar cabinet (open), sounds good probably doesn't do the tone justice when "live". Not sure I what to humfph around a 4x12" cab the head is heavy and big enough! so I've been looking at 2x12" the orange PPC212 open back or the closed back version Anyone had any experience with this or any other 2x12" closed or open backs?
  11. JaseFIJo

    Voicing Setting

    Useful info, so many things to mess around with and not enough time! ;) Thanks Jason
  12. JaseFIJo

    Voicing Setting

    I've hooked up my HD500 to the DT50 head (line6 link) and have a few patches switching various pre amps in and out. My question is what happens when you disconnect the HD500? The reason for this question is does the HD head remember the last pre amp selected on the channel via the HD500 or does it revert back to the base settings in the head? When I go guitar direct to the jack with no HD500 the DT50 is the base condition "out of the box" other changes on the front dials. I'm just a little confused on how this routing works. When you switch channels A to B and back the head will remember the configuring set from the previous time the channel was used how does the HD500 effect/interact with this. Thanks
  13. JaseFIJo

    M5 output straight to mixer?

    Bought one last week an hooked it direct to my desk and used my DI box both work. No amp modelling you'll need to get a POD "something" number Great if you don't want to transport a load of gear around
  14. JaseFIJo

    monkey 1.7

    just installed version 1.70 Norton complaining of suspicious activity noted as potential sonor heuristics 120 Trojan. So unistalled and installed version 1.67 runs without Norton flagging suspicious activity with the new version? Anyone else have the same
  15. OK must be some sort of file corruption or data transfer issue with 2.1. tried a couple of times to reload it over itself but issue was still apparent and tried to set tuning to what they should be with no luck. So: 1. Re-installed version 2.00 via Monkey 1.67 - Everything back to normal and all tunings normal , at least what they are supposed to sound like 2. Checked everything looked ok with workbench HD 2.1 3. Gave version 2.1 another go via Monkey 1.67 - Everything normal and tuning normal however look a the tuning "manage" box attached. Looks a bit like the problems I was experiencing in "lost tunings" stepped on the thumb wheel I'd updated to version 2.1 pretty much as soon as it came out and have not connected workbench HD for a few months, why with no changes would it suddenly start to act up if there was not some sort of small bug out there is it potentially and issue with the VDI link to a POD500 v2,32 and the patches there. Is version 2.2 on the way Problem solved happy it was not a physical issue, it's probably worth noting
×