Search the Community
Showing results for tags 'leds'.
Found 4 results
Hi Line 6 Users, I have the POD GO and I am slowly learning how to use it... I am using an expression pedal with it so I can use both the Wah and Volume feature... does anyone know if there is a way to have the EXP LED turn on and off depending on whether you have the effect on or off? For example, when using the WAH, the LED is on when activated but off when deactivated? This happens automatically on my Spider IV when using the FVB Shortboard MKII but I can't work it out for the POD GO Many thanks
Hello, This unit has always worked without any issue, but all of a sudden I connected it as usual and it didn't turn on. At the beginning I thought it was completely broken but because I was still hearing that click after turn it on, I tried connecting the USB to the computer and realized that it was working there as usual, and the effects too when connected to the amp. I've tried resetting and reinstalling the firmware but it's still the same. Have anyone experienced the same issue or something similar?
All 4 tone lights (or ABCD lights on the FX100) flashing is 'recovery mode'. It is the intended behavior after a failed update. If you come across this mode, you must attempt to update the AMPLIFi again. Power down your AMPLIFi. When updating via PC, please connect the USB cable and make sure to boot the unit while holding Tone+Tap (amp, TT) or A+C (FX100) to put your AMPLIFi into Update Mode. Run the Line 6 Updater program found at www.Line6.com/software. For a guide, please refer to http://line6.com/support/page/kb/_/amplifi-products/ampl/how-to-update-amplifi-with-a-pc-r701. If you still get failed updates from the Line 6 Updater, try another USB cable and port as well as another computer When updating via an iOS device, Bluetooth works in recovery mode, but the pairing from before the failed update is not maintained. You must press the Bluetooth button and pair again from the smart device's Bluetooth menu. You can then proceed with the update.
Thanks for viewing my Post. Heres my issue with as much detail as I can possibly Muster. I have started this specific thread because I am connected only to a MAC computer (compatible SierraOS) I DO NOT have a POD, or any other connected device and only seem to find threads with issues to connect to other devices or threads that get derailed / go nowhere. Trying very hard to be Patient as the Guitar plays like a Dream just doesn't Model ;) Here we Go: 1. I have a New JTV59 with the Included Battery, Charger and USB interface (VDI?) and accompanying "ethernet" cable, Pilots Handbook, Allan wrenches etc... 2. I have Charged the Battery Fully (Over twelve hours with slow red blink on charger) 3. I have 4 Green LEDs on the back that stay on for 3 seconds and disappear when the Battery is placed into the Guitar. 4. I have Sound working with Magnetic Pickups only (like any regular guitar would) through 1/4" jack 5. I have Monkey Recognizing the USB interface 6. I have Installed the Latest versions Monkey and Workbench HD (as monkey prompted me to) 6. I have the 1/4 inch Jack and VDI "Ethernet" Cable attached to the Guitar Despite attempting all the different suggestions on this Forum 1. I do not have any LEDs lighting under the Modeling or Alt-Tuning Knobs 2. The Four Green LEDs on the Back flash a few times when pressing the little Circular switch then turn off 3. Monkey Does not recognize the Guitar 4. WorkBench HD does not recognize the Guitar 5. USB interface Is Green (computer side) and Flashing Red (Guitar Side) 5. I do not hear any "Relay Click" when the 1/4" standard guitar cable is connected (With or Without VDI connected) 6. I have no Modeling sound whether through an amp connected to 1/4" I have tried adding pieces of Paper to the inside of the Modeling Knob (Which 1/100 times will "Click" when pressed down) I have tried Switching the "Tone Switch" to Position 3 and 5 with Modeling knob in position Custom 1 I have tried to wear the battery down a bit and reseat it numerous times. I have tried to check the internal Contacts of the Battery Case with a multimeter and see expected voltages being provided by the Battery. The three contacts from battery to case are firmly seated. I Have tried using a different "Ethernet" Cable (This is the last thing I've tried) I am in Mexico for two months and do not have the ability to simply return the Guitar for a replacement. Happy to provide any further information / Photos / Video!!! Truly Hoping someone on this Forum can help a Guy out! :D Much Appreciated :D