Please ensure Javascript is enabled for purposes of website accessibility Jump to content

Search the Community

Showing results for tags 'switching patches'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Community Support
    • Multi-Effects Units
    • Variax Instruments
    • Amplifiers
    • Computer Based Recording
    • Live Sound
    • Pedals/Controllers
    • Dream Rig - Line 6 Product Integration
  • General Discussion
    • Tone Discussion
    • Line 6 Lounge

Categories

  • General FAQ
    • Operating System-specific Information
  • Tutorial Videos
  • Effects/Controllers
    • HELIX/HX
    • DL4 MkII Stompbox Modeler
    • M5
    • FBV Controllers (MKII / 3)
  • Amplifiers
    • Catalyst
    • Powercab
    • Spider V
  • POD
    • POD Go
    • POD Express
    • Pocket POD
  • Guitars
    • JTV / Shuriken / Variax Standard / Workbench HD
  • Relay G10 Digital Wireless
  • Recording
    • Helix Native
    • Metallurgy
    • Echo Farm/Amp Farm
    • POD Farm 1/2.0/2.5
    • Computer Audio Set Up and Troubleshooting
  • Legacy Products
    • POD
    • Amps
    • 1st Gen Variax Guitars / Bass / Workbench
    • Effects and Controllers
    • AMPLIFi Series
    • Live Sound
    • Digital Wireless
    • Mobile Products
    • POD Studio / Tone Port / GuitarPort
    • Software
    • Dream Rig

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Location


Interests


Registered Products

Found 3 results

  1. Hi all New owner of a HELIX floor unit here. I have been enjoying the unit for a few weeks now and have a few questions as I am about to start dabbling in snapshots. so as of now I have my unit set up like I did with my old hd500x. rhythm channel on one pre set high gain on another clean and lead etc etc etc. This use to work and I had gotten use to the slight delay in changing presets, with this floor unit its a bit more complicated for my preset switching. I need the ability to switch on and off effects and switch in-between presets during a song and I know snapshots can do this in a different manner then just switching a channel, I know it can activate and de activate amps and peddles etc. what I am trying to understand is this. If I want a rhythm clean and lead channel lets say, I understand that I have to make 3 snapshots and make sure all the effects and amps will fit in 1 preset due to dsp, what I don't understand is how I can switch the snapshots. like can I use the bottom 3 buttons to the right of the bank up bank down buttons for snapshot 1 2 and 3 and the rest for stomps? if so do I have the ability use 2 buttons one for clean and one for lead, and when I select the clean snapshot the foot controller that it was assigned to if pressed again could switch to my rhythm? I go to preset 1 all my snapshots are there. its already set to snapshot one (rhythm) I have all my stomp boxes set to other foot controllers other then the 2 that would switch to snapshot 2 and snapshot 3. lets say I need to go to lead (snapshot3) I press the button the lead snapshot is loaded but that button if pressed again will take me back to snapshot 1? is this possible?
  2. I'm running my Helix in 4CM. I have it configured whereby I'm using a bank of presents for a 'song', and the patches saved within the bank are for different sounds within the song (such as a solo boost, etc...). Problem: I switch from one patch to another and there is a 1/4 second of silence during the switch - a complete dead spot with no sustain, etc... Is there a setting or switch that I can enable to stop this from happening? Incidentally, I started using a single patch for a song, and set up the snapshots for the different sounds within the song. That didn't have the same issue, but I found that configuration more time-consuming to set up and maintain - as well as less user-friendly. I would like not to go back to that configuration. Would appreciate feedback on this! Thanks!
  3. Hey Guys, So I've been running a PODHD500 into a DT50 (112) using the Line6 link. I have all my patches volumes carefully set evenly to make sure they boost appropriately for leads etc. I run the Master on the POD all the way up and the Master on the Amp at around 9 oclock for most rooms we play. The problem I've been having lately is that when I change patches (say for example to my lead patch), the volume goes WAYYY too high all of a sudden, even though I have it set at a comfortable level normally. Then, If I click the same patch footswitch a second time, the volume goes back to normal. I've made sure of the obvious, that my levels werent accidentally adjusted and Im not accidentally hitting any volume knobs. I have all the latest firmware, and take great care of my gear, so I'm a little dumbfounded. please help if you've experienced this. Thanks! Jordan
×
×
  • Create New...