Pwm5k Posted September 28, 2013 Share Posted September 28, 2013 Hi, I'm just got my DT25 HD today. And I'm going to use the cabinet simulated direct out to my Focusrite Saffire Pro 24 audio interface, but I'm not sure which input to plug to, should I plug to line input or the preamp input of the audio interface? Thanks! Quote Link to comment Share on other sites More sharing options...
BigChas52 Posted September 28, 2013 Share Posted September 28, 2013 I would think line input. Try them both to see which gives you the better results. Quote Link to comment Share on other sites More sharing options...
geppert Posted September 28, 2013 Share Posted September 28, 2013 Hi, I'm just got my DT25 HD today. And I'm going to use the cabinet simulated direct out to my Focusrite Saffire Pro 24 audio interface, but I'm not sure which input to plug to, should I plug to line input or the preamp input of the audio interface? Thanks! The Cabinet Simulated Direct Output on the rear of the DT-25 is a "microphone-level" sampling the output from the analogue circuitry just before it is fed to the speaker, to which a simulation of the speaker, cabinet and microphone defined in the POD HD preset have been applied. You may need to use the Pre-Amp input on your Pro 24 to bring the level from the DT25 up to where you need it? As BigChase52 said ... try both to see which works best. Quote Link to comment Share on other sites More sharing options...
Pwm5k Posted September 29, 2013 Author Share Posted September 29, 2013 Ok, thanks alot Bigchase52 & geppert for the reply. I'll try later on. :) Quote Link to comment Share on other sites More sharing options...
phish_200 Posted April 14, 2015 Share Posted April 14, 2015 did any of this work? I am trying to direct out to an audio interface (RME fireface UCX) and i just get no output at all - does anyone know what I might be doing wrong. I am directing the output into the microphone input on my interface with a microphone cable. Quote Link to comment Share on other sites More sharing options...
sonic Posted April 14, 2015 Share Posted April 14, 2015 did any of this work? I am trying to direct out to an audio interface (RME fireface UCX) and i just get no output at all - does anyone know what I might be doing wrong. I am directing the output into the microphone input on my interface with a microphone cable. Do you have your DT in Standby ? Are you using LVM or not ? In normal mode the amp needs to be out of standby... Sammy Quote Link to comment Share on other sites More sharing options...
phish_200 Posted April 15, 2015 Share Posted April 15, 2015 Do you have your DT in Standby ? Are you using LVM or not ? In normal mode the amp needs to be out of standby... Sammy thanks for your response. I dont have my DT in standby and I am not using LVM. so yeh the amp doesnt work at all if its in standby does it? Quote Link to comment Share on other sites More sharing options...
sonic Posted April 15, 2015 Share Posted April 15, 2015 thanks for your response. I dont have my DT in standby and I am not using LVM. so yeh the amp doesnt work at all if its in standby does it? In LVM it does, but in normal mode it does not, unfortunately... mmm, did you check the cable and mic input of the RME ? Quote Link to comment Share on other sites More sharing options...
spaceatl Posted April 15, 2015 Share Posted April 15, 2015 hmmmm......Double check you have not accidentally plugged into the System Link output....I did this once or twice...It's a little close to the XLR Analog Out on the DT25 head.... Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.