guilhordas

strangely I just hear distortion when I put the mixer before the amp. I do not see the point in open pans because I use my pod mono, only use one XLR cable in out I started to notice this distortion when one ran boss rc2 loop in out 1/4 pod , through a Cable 1 /4 (pod oult 1/4 / in loop pedal / pedal out to mixer), when I record and listen to the loop notice that diostorcion this, but after I put the amp after the mixer not distorted more, I do not know if I'm right. Am i running right my setup?

in my case i use pan in the center

only today, after four years using the pod hd, I noticed that put the amp block before or after the mixer block makes a lot of difference in tone and volume. Where you guys guys think better? Even if the volume on mixer is 0 thera is tone difference

to my ears, the sound of magnetic, through the vdi is absolutely different from the sound through the 1/4, as water and and wine. in 1/4, the tone is much more natural. as I do not own the more jtv battery (is dead), a way I found was to connect the cable vdi only to feed the guitar and use a cable 1/4 simultaneously . On pod I disable the Variax in 2 inputs and set to guitar and aux . On Variax control (utilities/pod) I set into global (do not force) this way I have the sound of models only through 1 / 4, which in my opinion sounds much better, even in models

Im looking for sustain for solos, kind of david gilmour, what comp and and configuration do you suggest? thanks

thanks your help, i dont use any stereo effects

I own a blackstar, 2 drive pedals and a pod hd 500x, I intend not to use the pod as simulator, just like modulation and effects, you guys really think I need to run the pod to blackstar loop or should I run on in the blackstar, remembering that Im not using pod pre amps pod, only effects. 4cm seems to me very hard work to do live, I want to use pod like a pedal thanks

have you tried this patch direct in mixer, on gigs? because i think that the sound changes a lot on PA, in the record is easier sound well

try tweed b man brt/421 dynamic/4x12 highway/15% gain /volume full the best clean sound, full and warm

in this method where i put my drive pedals?

Where do I put my drive pedals in a 4CM way?

I use the studio in eq exp2 without equalizing flat, I set, the min in a way that does not change the actual volume and the maximum to taste, works great for me

this is great for chorus

How should i proceed on my patches to send the signal of Acoustics sounds direct to the mixer? I know that i have to use the fx loop , but how? And what about the patch and the connections cables, how should set up? Thanks

the tone sounds completely different, harsh , it doesn't depends of the gain, but in the beginning of the chain sounds very good

input of what? i use outupt max phase 0 gain , enought to balance the volume between with or without vintage pre, around 39 100 k and 5,5 k

yes, exactly, but I think it impossible to use at the end of the chain, the sound totally distorts

I have a problem here, you guys sure that the best thing to do is put the vintage pre at the end of the chain? here sounded horrible like this, it sounds quite harsh, but at the beginning of the chain sounded fine

It is sure that the sound of byp volume does not come along when the amp block is on ?in doubt, I always set, the byp zero

when you turn off the amp appears on the pod hd vol BYP, I always disabled it(turn off this volume) , gives me the impression that the sound mixes with the sound of the amp and it sounds bad. My question is what is the real function of this volume BYP?

is very weird, even if I'm using the 2 inputs in the guitar and aux , if I press the patches on pod models sound , models should not be mute when I Set The inputs this way?

I recorded these 2 samples for you to hear the difference, first sample of each track is always with 1/4 in the second with Vdi, notice how different sounds the guitar in z is on auto

Funny thing, I was doing login right now to comment precisely what you said, I think you're right, guitar in z makes a good difference in tone

another question, the tone of real pickups should sound exactly the same when I use the vdi cable or the 1/4? does not sound to me, on the contrary, they sound very different

I still could not figure out, but the real pickups only sound good when I run 1/4 cable, with the cable vdi not;. I use my inputs 1 variax and 2 guitar is there any secret on pod hd to set? and , every time that i press another preset the models get turn on, do i have to push off models button all time that i want to use the real pickups?