Please ensure Javascript is enabled for purposes of website accessibility Jump to content

Search the Community

Showing results for tags 'beltpack'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Community Support
    • Multi-Effects Units
    • Variax Instruments
    • Amplifiers
    • Computer Based Recording
    • Live Sound
    • Pedals/Controllers
    • Dream Rig - Line 6 Product Integration
  • General Discussion
    • Tone Discussion
    • Line 6 Lounge

Categories

  • General FAQ
    • Operating System-specific Information
  • Tutorial Videos
  • Effects/Controllers
    • HELIX/HX
    • DL4 MkII Stompbox Modeler
    • FBV Controllers (MKII / 3)
    • M5
  • Amplifiers
    • Powercab
    • Catalyst
    • Spider V
  • POD
    • POD Go
    • Pocket POD
    • POD Express
  • Guitars
    • JTV / Shuriken / Variax Standard / Workbench HD
  • Relay/XD-V Digital Wireless
  • Recording
    • Helix Native
    • Metallurgy
    • Echo Farm/Amp Farm
    • POD Farm 1/2.0/2.5
    • Computer Audio Set Up and Troubleshooting
  • Legacy Products
    • POD
    • Amps
    • 1st Gen Variax Guitars / Bass / Workbench
    • Effects and Controllers
    • AMPLIFi Series
    • Live Sound
    • Digital Wireless
    • Mobile Products
    • POD Studio / Tone Port / GuitarPort
    • Software
    • Dream Rig

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Location


Interests


Registered Products

Found 2 results

  1. Device Positioning for Updating XD-V7x Transmitters and Receivers Updating the TBP12 Transmitter (Relay G50, G90, XD-V55L, XD-V70L, XD-V75L) Updating the TBP06 Transmitter (Relay G30, XD-V30L, XD-V35L)
  2. I had an odd issue last weekend with one of my V70 belt-pack systems. I was running three of them plus my new V75 hand-held which I'd just used to update the firmware in all the V70 systems. All in RF1 mode. This particular system had the L6 lav mic attached (I normally use headsets but this particular performer insisted on a tieclip). The system was used on someone else earlier in the show and performed perfectly, but once fitted to this performer, the problem hit. I PFL'ed him just before he went out on stage and all I heard was a loud mains-type hum with some harmonics and a slightly digital quality to it. No wanted audio at all; just this unvarying buzzing. I think the level was lighting up just the bottom segment of the receiver meter. It was far too late at this point to swap anything out but as he projected well, he made it through his act without the mic. As it was a somewhat hectic show followed by a rapid get-out, I didn't have the time to go through any useful troubleshooting to narrow down what the problem might have been; unhelpful I know. I set up the equipment again back at base and couldn't make it misbehave in any way no matter what I did. My best guess was a dodgy connection between mic & belt-pack but no amount of cable flexing and connector wiggling and loosening would produce any issues. The venue was at the bottom of a cliff on the seafront where even mobile phone signals barely made an appearance; with no venue WiFi either, it was the quietest RF environment I've ever worked in. The other systems all worked perfectly throughout; this one was also fine up until that one act. My question therefore (and I know it's a bit of a stab in the dark) has anyone experienced anything like this or can anyone suggest a possible cause?
×
×
  • Create New...