Please ensure Javascript is enabled for purposes of website accessibility Jump to content

Search the Community

Showing results for tags 'cycle'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Community Support
    • Multi-Effects Units
    • Variax Instruments
    • Amplifiers
    • Computer Based Recording
    • Live Sound
    • Pedals/Controllers
    • Dream Rig - Line 6 Product Integration
  • General Discussion
    • Tone Discussion
    • Line 6 Lounge

Categories

  • General FAQ
    • Operating System-specific Information
  • Tutorial Videos
  • Effects/Controllers
    • HELIX/HX
    • DL4 MkII Stompbox Modeler
    • M5
    • FBV Controllers (MKII / 3)
  • Amplifiers
    • Catalyst
    • Powercab
    • Spider V
  • POD
    • POD Go
    • POD Express
    • Pocket POD
  • Guitars
    • JTV / Shuriken / Variax Standard / Workbench HD
  • Relay G10 Digital Wireless
  • Recording
    • Helix Native
    • Metallurgy
    • Echo Farm/Amp Farm
    • POD Farm 1/2.0/2.5
    • Computer Audio Set Up and Troubleshooting
  • Legacy Products
    • POD
    • Amps
    • 1st Gen Variax Guitars / Bass / Workbench
    • Effects and Controllers
    • AMPLIFi Series
    • Live Sound
    • Digital Wireless
    • Mobile Products
    • POD Studio / Tone Port / GuitarPort
    • Software
    • Dream Rig

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Location


Interests


Registered Products

Found 2 results

  1. I'm writing a song that uses a square or saw tooth tremelo effect synced to the beat with a 100% intensity for the primary rhythm element. I've found that though you can sync the tempo to the track, you can't control the start of the tremelo cycle with the DAW to sync it up with other elements. This means that each time you start the track, the phase of the cycle may not be what you expect. That makes it very difficult to sync up properly... For example, I've set up a sine wave generator, then an instance of Helix Native with a single Modulation > Mono > Tremelo: I've then set up my DAW to enable the effect at a particular spot in the "song" so that the effect would theoretically start the cycle the same each time. Then, I rendered the same section of song 3 times and added them to the project. As you can see, the first bar is the solid block sine wave, and then the tremelo effect is kicked on. You'll notice that the phase of each cycle is quite different, even though they all are turned on at the exact same time. (Three may have been me accidentally leaving one unmuted before the next render) Next, I attempted to bypass the Helix plugin entirely, rather than just the tremelo effect block. The same behavior is exhibited. The start time of the cycle is entirely unpredictable, and appears to simply be running non-stop after you load the plugin into memory or something. As suspected, this is true for other Modulation effects as well. Here's the same test using a whole not with the Script Mod Phase effect: Helix Native needs to honor the Host Sync's start event (assuming that actually exists) to reset it's LFO for Modulation effects. Otherwise, results are unpredictable and potentially unusable during rendering. :( I haven't tested the Helix Floor pedal to see if the bypass/enable of a trem effect resets the LFO, but I wouldn't be surprised if it had the same basic problem...
  2. Hey L6 Forums, New HX Effects user here. Really liking it so far! I do have a question about Snapshots, though: On my main preset, I have 4 Snapshots set up - Clean Electric, Acoustic Sim, Overdrive, and Fuzz. I have the Clean Electric Snapshot set up as the base tone of the preset, and therefore it's not assigned to a footswitch. I'm trying to use the other 3 snapshots to swap in and out different sounds with one touch. Is there a way to set the Acoustic Sim, Overdrive and Fuzz snapshots to bypass automatically when I press the footswitch for one of the other Snpshots? I'm looking to avoid hitting the snapshot footswitch a second time, only to have it bypass the snapshot I wanted to change back to. I still want the release function on the switches for Acoustic, Overdrive and Fuzz to take me back to my Clean Electric snapshot, though. Is this possible?
×
×
  • Create New...