Search the Community

Hi, as much as I love my HX Stomp I'm currently stuck with the following issue (or challenge): I got 3 snapshots, the usual clean, breakup, heavy crunch I got two external footswitches, which do not have led-rings. FS-4 turns a solo boost on and off (i.e. stomp mode-ing an EQ) and FS-5 turns a chorus on and off. This works basically great, but in the heat of the moment I'm not always sure what is on and what is off. Question: Can I configure the existing led rings on FS 1-3 to change color according to the state of the boost and/or the chorus? It seems like a waste to just have them shine white if their respective snapshot is on... Thanks a bunch! chris

Hi together, I wonder how to maintain expression pedal state Exp1/Exp2 and FS5 state of SP1-L6H between Presets. I set in Globals / Footswtiches ToggleExp to FS5 Therefore when Exp1 is active and I press toe Exp2 will be adressed back and forth. Each time I press toe a FS5 will also be sent. I use it with the HxStomp to use the toe to switch adevice on and the other off together at the same time with the neat functionality that the pedal changes EXP1->EXP2 I can control 2 continous parameters together nicely .... until I switch presets then my problem starts! let me explain! For instance: Preset A: Volume Positon mapped to Exp1 Wah Positon mapped to Exp2 Bypass Assign both FS 5 Initially Wah is bypassed Preset B (Same as A): Volume Positon mapped to Exp1 Wah Positon mapped to Exp2 Bypass Assign both FS 5 Bypass Assign FS 5 Initially Wah is bypassed 1) On Preset A I press Toe and Volume is bypassed, wah goes on - Wah position is controlled by Exp2 2) I change preset to B 3) PROBLEM: The system recalls that Exp2 is active but on Preset B is Wah Bypassed and the Volume Pedal is Waiting for Exp1 4) If I press Toe I turn off Volume in Favor of WahWah but I also switch from Exp 2 back to Exp 1.. deadlock!! Now I have to manually turn off the Wah and turn on the Volumen Pedel and than I can use the smart switching between Exp1 and Exp 2 again but only as long as I stay in the preset. If I got to next preset the described problem persist. I can not imagine that this is expected behavior. I need something like a reset of the Exp1/Exp2 switch state If I enter a preset or maybe you have an Idea how to do ? Help much appreciated!

Hi again guys, I have a question: Got my ‘baby’ board set up for vocal and guitar with the Stomp at its heart for the guitar FX (photo). As mentioned in a previous topic, I have FS4 & 5 acting as Page < and Page > (the two-button switcher under the Stomp). Everything is working fine. I have a dedicated Wah effect working separately from the Stomp. Question is about whether there’s a way to utilise FS4/5 when needed AND Exp1 (to access wahs, whammys, etc). Previously, Phil_M helpfully suggested a DMC MIDI pedal through which Exp1 could be accessed. I could go down that route if necessary. My question is - could a simple, bespoke, single button A/B switcher with TRS output allow switching between the stereo signal from FS4/5 and a mono (tip) signal from an expression pedal for Exp1 function? Cheers, Andy

Hello, I am new to this forum and bought a HX Stomp to accommodate my AX8 or simply have a tiny wonderbox that fits in my guitarcase, including guitar that is ;–) I hooked a Lehle Mini footswitch up to use it as FS4. Can’t find a solution to send a midi PC command from the footswitch to midi out of the stomp. Don’t tell me the stomp is limited to 3 PC messages that can only be sent by its own FS 1-3. I can switch a block on and off with the ext. FS, but can’t trigger that midi PC. I hoped for a better midi out implementation, but still love this little thingy...