Elephantstomp Posted July 27, 2020 Share Posted July 27, 2020 Hello, my HX Stomp shows a strange behavior sometimes. Suddenly ALL presets/snapshots (clean and crunch) have too much gain/saturation in a muddy way. But it doesn´t sound like a broken cable or hardware failure. Just like dialed in too much gain. It happend several times and every time when i tweaked something in HX Edit. One time i could "reset" it with switching the unit off and on. Another time with a backup restore. This time both didn´t help to get back to a "normal sound state". I listen to Headphones connected to the HX Stomp, so no extern Hardware involved. Has anyone experienced this too? I guess/hope this phenomenon is gone tomorrow. It´s unpredictable and i can´t identify a cause for this. My HX Stomp is not reliable with that strange behavior. Thank you Quote Link to comment Share on other sites More sharing options...
codamedia Posted July 27, 2020 Share Posted July 27, 2020 3 hours ago, Elephantstomp said: It happend several times and every time when i tweaked something in HX Edit. So the million dollar question is... "what did you tweak when it occurred"? (it may be a single event, it may be a series of events) You may not know (or remember) right now, but take note of it when it happens again. Then do a restore to normal, and try to repeat that same problem! 1 Quote Link to comment Share on other sites More sharing options...
Elephantstomp Posted July 28, 2020 Author Share Posted July 28, 2020 I thought it´s a bug. But now I wonder why it stayed after the reset/restore. I'll tell you when I'm smarter. 1 Quote Link to comment Share on other sites More sharing options...
FortyPsi Posted July 28, 2020 Share Posted July 28, 2020 Hi, Have you changed your output from Instrument to Line? 1 1 Quote Link to comment Share on other sites More sharing options...
Elephantstomp Posted July 28, 2020 Author Share Posted July 28, 2020 No, I changed nothing at the input or output. Input is Instrument and Output (Main, TRS) is Line level as always. Quote Link to comment Share on other sites More sharing options...
codamedia Posted July 28, 2020 Share Posted July 28, 2020 Backup any custom presets you made.... Try a complete RESET of the Stomp and see what happens.... 1 Quote Link to comment Share on other sites More sharing options...
Elephantstomp Posted July 29, 2020 Author Share Posted July 29, 2020 I already made a full restore and backup restore before I wrote. So...yesterday I switched on my Stomp and it had a proper sound again. I suppose that my previous repairs had nothing to do with a backup restore. I guess it´s a kind of DSP overload or bug caused by tweakings and copying presets and snapshots around and renaming. When after this the Stomp is switched off a certain time, the problem is gone (I hope that will be the case in future). I can live in peace again when it´s like that. Quote Link to comment Share on other sites More sharing options...
codamedia Posted July 29, 2020 Share Posted July 29, 2020 8 minutes ago, Elephantstomp said: When after this the Stomp is switched off a certain time, the problem is gone I don't want to be negative.... but that just doesn't seem right to me. If it has to sit for a period of time, that's a "cool down period", not just a software reload. If this unit is under warranty, I would be using it! 1 1 Quote Link to comment Share on other sites More sharing options...
Elephantstomp Posted July 29, 2020 Author Share Posted July 29, 2020 You are right! It worries me as well. But unfortunately I am in my 13th Stomp month. I registered my Stomp for a 2nd year of warranty, but I am no US customer :-( Quote Link to comment Share on other sites More sharing options...
codamedia Posted July 29, 2020 Share Posted July 29, 2020 58 minutes ago, Elephantstomp said: You are right! It worries me as well. But unfortunately I am in my 13th Stomp month. I registered my Stomp for a 2nd year of warranty, but I am no US customer :-( I would suggest you get in touch with Line 6 through their ticket system.... They have different distributor agreements throughout the world.... they may be able to help or their hands may be tied. You won't know until you contact them with your problem. 1 Quote Link to comment Share on other sites More sharing options...
HonestOpinion Posted July 29, 2020 Share Posted July 29, 2020 On 7/27/2020 at 2:00 PM, Elephantstomp said: Hello, my HX Stomp shows a strange behavior sometimes. Suddenly ALL presets/snapshots (clean and crunch) have too much gain/saturation in a muddy way. But it doesn´t sound like a broken cable or hardware failure. Just like dialed in too much gain. It happend several times and every time when i tweaked something in HX Edit. One time i could "reset" it with switching the unit off and on. Another time with a backup restore. This time both didn´t help to get back to a "normal sound state". I listen to Headphones connected to the HX Stomp, so no extern Hardware involved. Has anyone experienced this too? I guess/hope this phenomenon is gone tomorrow. It´s unpredictable and i can´t identify a cause for this. My HX Stomp is not reliable with that strange behavior. Thank you Opening a ticket sounds like the way to go but despite the fact that it seems unlikely have you have tried swapping out guitar, guitar cables, and trying a different pair of headphones to ensure that this is a problem with the HX Stomp? 1 Quote Link to comment Share on other sites More sharing options...
Elephantstomp Posted July 30, 2020 Author Share Posted July 30, 2020 It´s clearly the stomp. I tried different headphones, cables, guitars. A ticket is opened. I will tell you. Thanks for your help. Quote Link to comment Share on other sites More sharing options...
Elephantstomp Posted July 31, 2020 Author Share Posted July 31, 2020 Update: The Line6 Support suggested to reinstall the latest firmware, reset and rebuild the factory presets without restoring my backup and test. I did, but same results/failure. Now I send my stomp a service center (as suggested when the testing is unsuccessful). In europe respectively germany we have 2 years warranty. I forgot about that. 2 1 Quote Link to comment Share on other sites More sharing options...
Elephantstomp Posted August 3, 2020 Author Share Posted August 3, 2020 I really don´t get it. The "too much gain-phenomenon" no longer occurred the last days. Did the software reinstall help delayed?! I tried to summon the the disorder to get an information afer which time it happens...but nothing. I keep and use my stomp and don´t send it to the service center until it happens again. My dealer gives a bonus year of warranty, so in total I have three years. That's pretty nice and no need to hurry. 1 Quote Link to comment Share on other sites More sharing options...
BackSlash33 Posted October 19, 2023 Share Posted October 19, 2023 Hello, I think i had the same problem : on all amps, saturated sounds (drive between 5/10) seem to add noise/break on signal. I also flash firmware to latest, reset to factory etc without change... (and try many cables, or other cab, guitar..) I was forced to send the helix floor back to seller support for repair/investigations (they add 1 year warranty too thanks !) but they told all was ok for them. (they may did something because problem was solved for weeks) For now, the problem is back and still persists, maybe : - too load on DSP ? - an electronic component failure ? - latest firmware additions may charge the DSP more than before ..? So bad, to reproduce, simply play a powercord, palm-muted, and it may appears. Thank you for any feedback on subject. Best regards Quote Link to comment Share on other sites More sharing options...
Elephantstomp Posted October 28, 2023 Author Share Posted October 28, 2023 The problem was caused by my Shure GLXD16 (wireless). A broken cable caused the "too much gain phenomenon". My HX-Stomp works flawless since I used a new cable. Could´t find it out so easy because the issue occured sporadically. I hope you get this problem solved! 1 1 Quote Link to comment Share on other sites More sharing options...
brue58ski Posted October 31, 2023 Share Posted October 31, 2023 On 10/19/2023 at 7:24 AM, BackSlash33 said: Hello, I think i had the same problem : on all amps, saturated sounds (drive between 5/10) seem to add noise/break on signal. I also flash firmware to latest, reset to factory etc without change... (and try many cables, or other cab, guitar..) I was forced to send the helix floor back to seller support for repair/investigations (they add 1 year warranty too thanks !) but they told all was ok for them. (they may did something because problem was solved for weeks) For now, the problem is back and still persists, maybe : - too load on DSP ? - an electronic component failure ? - latest firmware additions may charge the DSP more than before ..? So bad, to reproduce, simply play a powercord, palm-muted, and it may appears. Thank you for any feedback on subject. Best regards Just a suggestion, I have no idea if it will work but try changing the input impedance as well as maybe turning on the pad. The pad is in Global Settings under Ins & Outs. Quote Link to comment Share on other sites More sharing options...
Thienpont Posted October 31, 2023 Share Posted October 31, 2023 The same happened to my Stomp. Everything worked fine for a month, but then one day, when I switched the Stomp on, all preset suddenly sound all as if bass was at 10 and treble at 0 and max gain. All presets are now super muddy. A reset did not fix the problem. So, now I'm stuck with a Stomp that sounds awful. I hope someone finds a fix. Quote Link to comment Share on other sites More sharing options...
datacommando Posted October 31, 2023 Share Posted October 31, 2023 On 10/31/2023 at 8:54 PM, Thienpont said: The same happened to my Stomp. Everything worked fine for a month, but then one day, when I switched the Stomp on, all preset suddenly sound all as if bass was at 10 and treble at 0 and max gain. All presets are now super muddy. A reset did not fix the problem. So, now I'm stuck with a Stomp that sounds awful. I hope someone finds a fix. Hi, Firstly, when seeking assistance with unpredictable issues such as this, a “me too” post isn’t very helpful. It’s a good idea to supply as much information as possible; it may help to narrow down potential causes. For example, what are you connected to/monitoring the audio through? What version of the Firmware is installed on your device? Have you tried re-flashing the firmware? Hope this helps/makes sense. Quote Link to comment Share on other sites More sharing options...
Thienpont Posted November 1, 2023 Share Posted November 1, 2023 On 11/1/2023 at 12:34 AM, datacommando said: Hi, Firstly, when seeking assistance with unpredictable issues such as this, a “me too” post isn’t very helpful. It’s a good idea to supply as much information as possible; it may help to narrow down potential causes. For example, what are you connected to/monitoring the audio through? What version of the Firmware is installed on your device? Have you tried re-flashing the firmware? Hope this helps/makes sense. Makes sense. Problem is that I cannot tell much. I run the latest firmware 3.60 and I already did a factory reset. What happened is I enjoyed playing, as the stomp preset sounded great, at the end of my playing I switched off the stomp and went to sleep, the day after when I switched on the stomp all preset sounded super muddy. What I also experience (not sure if it is related to my bigger problem): - sometime when I switch on the stomp, no sound at all from the stomp. So I have the switch off and switch on to get sound again. - sometime when I am using HX edit, connection is lost and again I need to switch off and switch on again to get the stompt connected. These 2 issues look like more like bad software. Usually bad software is fixed with reboots. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.