Please ensure Javascript is enabled for purposes of website accessibility Jump to content

Nope...that didn't do it (Stadium XL USB and app)


PiFromBRC
 Share

Recommended Posts

I updated to 1.4 yesterday, thrilled that when I went to connect it said "USB-Update". Update went well, but the app is only recognizing USB-Update and not the actual USB connection. I'm right back to having to put in the IP. W11 user.

 

image.png

  • Upvote 1
Link to comment
Share on other sites

I had similar at first. I connected to USB update and it connected itself and switched itself over. However was struggling with wifi so not sure what was going on where.

 

What I did notice was that the timezone had reset so I updated that.

 

I also restarted both the Stadium and my Macbook

 

After all those USB detection has been fine.

 

No idea which of these did it or if it was just chance but its been fine since. My only problem is that I used to have a rock solid wifi connection to the Stadium but now its useless since this update as it disconnects after about 10 seconds or so

Link to comment
Share on other sites

I'm having the same issue. I've updated the firmware and the application but I get an error saying USB is for updates only. I've tried uninstalling the app and the drivers and blowing away all folders but after reinstall the same issue pops up. I have no idea what to try next.

I'm having the same issue. I've updated the firmware and the application but I get an error saying USB is for updates only. I've tried uninstalling the app and the drivers and blowing away all folders but after reinstall the same issue pops up. I have no idea what to try next.

I'm having the same issue. I've updated the firmware and the application but I get an error saying USB is for updates only. I've tried uninstalling the app and the drivers and blowing away all folders but after reinstall the same issue pops up. I have no idea what to try next.

Edited by theancientone
Added screenshot of app version
Link to comment
Share on other sites

On 10/16/2026 at 3:48 PM, Wah-bisca said:

@PiFromBRC, can you try the following:
 

@PiFromBRC

UsbNcm Host Device 2 showed up. No tree called 'Other devices'. Went through the process on the UsbNcm as you described for the CDC NCM. That didn't work.
image.png

Link to comment
Share on other sites

Having exactly the same kind of problem. Unit constantly disconnects because it stays on Wi-Fi even though the USBC is plugged in. Try to select it and it just shows the SBC for update and when selected it still goes back to the Wi-Fi for editing. Tried on two different computers. Same result all firmware and edit apps updated to 1.4

Link to comment
Share on other sites

On 10/16/2026 at 1:55 AM, msj12345 said:

I had similar at first. I connected to USB update and it connected itself and switched itself over. However was struggling with wifi so not sure what was going on where.

 

What I did notice was that the timezone had reset so I updated that.

 

I also restarted both the Stadium and my Macbook

 

After all those USB detection has been fine.

 

No idea which of these did it or if it was just chance but its been fine since. My only problem is that I used to have a rock solid wifi connection to the Stadium but now its useless since this update as it disconnects after about 10 seconds or so

I’m not sure I understand what you’re saying. If you have a stable usb connection why would you connect via WiFi?

Link to comment
Share on other sites

On 10/16/2026 at 8:47 PM, PiFromBRC said:

UsbNcm Host Device 2 showed up. No tree called 'Other devices'. Went through the process on the UsbNcm as you described for the CDC NCM. That didn't work.
UsbNcm Host Device 2 showed up. No tree called 'Other devices'. Went through the process on the UsbNcm as you described for the CDC NCM. That didn't work.

I don't see either one of those kind of host devices in my control panel at all. I downloaded and installed 1.4 as well as the driver download from line 6

Link to comment
Share on other sites

The time zone on the stadium reset from my UK time zone to the default USA one after the update
 

I use WiFi because I use it at home but since the update cannot so have to resort to usb and physically connect via a cable now. 

Link to comment
Share on other sites

I have the exact same issue.  I’ve tried connecting my Stadium to the app via USB on two different Windows PCs and neither work.
 

I’ve tried rebooting, reinstalling the app, turning WiFi and USB settings off and back on again, granting the Stadium app permission to go through the firewall, and a number of other things but nothing seems to work.  
 

I was going to try editing the UsbNcm settings per the suggestion above, but I don’t have any idea what that parameter is, and I received a warning from my computer that changing the setting was not recommended.  The last thing I want to do is crash my computer.  

I’ll just have to put up with regular app dropouts until somebody discovers a solution. 

Link to comment
Share on other sites

On 10/20/2026 at 4:12 PM, PiFromBRC said:

@MojoAxe

Not that I have a solution, but what version of windows are you on?

I'm running Windows 10 on a dell 3620 with an i7-7700 processor.  I've tried different cables and I've tried plugging into both USB 2.0 and 3.0 ports, and I installed the Stadium app onto one of my other machines (which is also Windows 10) and it still didn't work.  My wife has a machine with Windows 11 so I'll give that a try.

 

The cable I am trying to connect with is this: https://www.amazon.com/dp/B094XYJRZ2?ref=ppx_yo2ov_dt_b_fed_asin_title  This cable supports USB 2.0 data transfer rate up to 480Mbs.  Could the problem be that this cable is inadequate?

 

 

Link to comment
Share on other sites

On 10/20/2026 at 2:09 PM, MojoAxe said:

I'm running Windows 10 on a dell 3620 with an i7-7700 processor.  I've tried different cables and I've tried plugging into both USB 2.0 and 3.0 ports, and I installed the Stadium app onto one of my other machines (which is also Windows 10) and it still didn't work.  My wife has a machine with Windows 11 so I'll give that a try.

 

The cable I am trying to connect with is this: https://www.amazon.com/dp/B094XYJRZ2?ref=ppx_yo2ov_dt_b_fed_asin_title  This cable supports USB 2.0 data transfer rate up to 480Mbs.  Could the problem be that this cable is inadequate?

 

 

No, not what I meant. Press the windows key (key with 4 squares) + R and type winver in the field that pops up. It will give you a version like 25H2 and then a build number. 

Link to comment
Share on other sites

On 10/20/2026 at 8:11 PM, PiFromBRC said:

No, not what I meant. Press the windows key (key with 4 squares) + R and type winver in the field that pops up. It will give you a version like 25H2 and then a build number. 

 

Windows Pro, Version 22H2 (OS Build 19045.6466)

Link to comment
Share on other sites

Same problem here - can't connect via usb for editing.  Tried everything listed here, even uninstalled the app and the driver and re-installed.  Still can't use the app to edit via usb, only wifi. Updating to 1.4.1 didn't help.  Using Windows 10.

Link to comment
Share on other sites

  • 4 weeks later...
On 10/19/2026 at 8:57 PM, PiFromBRC said:

 @Wah-bisca @silverhead

Got any other ideas? I've got to imagine this isn't just me.  

Have you had any luck getting USB to work?  I've been working with Line 6 Support and so far nothing seems to work.  I did install the app onto my wife's Windows 11 machine and I was successful in connecting the Stadium to the app on her machine, so at least I've ruled out the Stadium unit or cables being the problem.  Using my wife's PC isn't an option.  The WiFi connection keeps disconnecting which is a major annoyance, so I need to get the USB connection to work on my own computer. 

 

I cannot connect Stadium to the app via USB on either of my Windows 10 computers.  I've uninstalled and reinstalled the app several times, and I even reset the Stadium to factory settings.  Under no circumstances will USB show up as an option to connect to in the app.  When the Stadium is cabled to the PC, it appears in Device Manager with a message that states "This device is working properly".  I've checked the firewall and it is allowing the Helix Stadium Editor to communicate through the firewall.  I've tried the USB 2.0 and 3.0 ports on both the frontside of the PC as well as the motherboard ports on the backside.  Out of curiosity, I also dug out my OG Helix, plugged it in to USB, and it connected to Helix Edit just fine.  There's something that's blocking the Stadium App from from the Stadium unit.  

 

Has anybody else been successful in connecting via USB on a Windows 10 machine?  I intend to upgrade to Windows 11, but I haven't found the time to do so.  I don't know if that would make a difference or not.

Link to comment
Share on other sites

On 11/17/2026 at 12:15 PM, MojoAxe said:

 

What did you do to get it to work?  I have tried everything that I, the Support team, and AI can think of, and yet I'm still unable to link the Stadium app to the Stadium unit via USB.  

 

You may have already tried this, however, have you used the USB-C to USB-C cable for computer to Helix connection?  And use the USB-C connection on the computer closest to the computer power supply if possible.  No USB hubs for this.  Just something to try if at all possible.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

×
×
  • Create New...